PelcoメーカーC2406M-Fの使用説明書/サービス説明書
ページ先へ移動 of 16
200 Series Camclosure ® Integrated Camera System C2406M-F (4/04) ® INST ALLA TION/OPERA TION.
2 C2406M-F (4/04) IMPORT ANT SAFEGUARDS AND WARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
C2406M-F (4/04) 3 DESCRIPTION The wedge style 200 Series Camclosure ® integrated camera system is designed to mount directly to a wall or ceiling. It also can mount to a corner with the ICS200-CM corner mount. The system incorporates a camera and lens package into a small, medium security enclosure.
4 C2406M-F (4/04) INST ALLA TION The following parts are supplied: 1 Camclosure integrated camera system 1W atertight mounting plate 1 1/8-inch pin-in-hex Allen wrench bit 3 10-32 x 0.5-inch Phillips screws 3 #10 internal tooth lock washers 1 Hole plug PREP ARE MOUNTING SURFACE 1.
C2406M-F (4/04) 5 INST ALL BASE WITHOUT CONDUIT 1. Outdoor Installation Only – Bring the power and video wiring for the camera through the wiring hole in the watertight mounting plate. Then fasten the mounting plate to the mounting surface with #8 stainless steel screws (not provided) of the appropriate length.
6 C2406M-F (4/04) bottom of the base (refer to Figure 5). Pull the wiring inside the base. WARNING: Be careful not to damage the wiring or the connection where the video cable is fastened to the circuit board. 3. Using the screwdriver bit that is provided, remove the conduit cover and plate by unscrewing the tamperproof screw .
C2406M-F (4/04) 7 REINST ALL CAMERA MODULE 1. Reinstall the camera module. Refer to Figure 8. Make sure the top of the camera is oriented properly . On the lens housing, look for the label that says TOP . WARNING: To prevent damage to the camera or lens, the camera must be installed in the proper hole of the mounting bracket.
8 C2406M-F (4/04) ADJUSTMENTS (COLOR CAMERA ONL Y) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary . 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit.
C2406M-F (4/04) 9 FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS To adjust the focus, do the following: 1. Loosen the locking screw on the bottom of the lens. T o loosen the screw , it may be necessary to remove the heater board. Refer to Figure 14 and the accompanying steps.
10 C2406M-F (4/04) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to Figure 16. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions where there are no bright spots that darken other picture details.
C2406M-F (4/04) 11 SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is configured at the factory for optimal performance in lighting conditions where auto iris is required. It is also configured with the shutter speed set at 1/60 (NTSC) or 1/50 (P AL) and AGC set at 6 dB of gain.
12 C2406M-F (4/04) (Design and product specifications subject to change without notice.) SPECIFICA TIONS General Pan/T ilt Adjustment: Manual; ± 10 ° pan; 5 ° above horizontal to 20 ° below horizo.
C2406M-F (4/04) 13 REGULA TORY NOTICES FCC Class A (monochrome, EIA cameras only) This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules.
14 C2406M-F (4/04) W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
C2406M-F (4/04) 15 REVISION HISTORY Manual # Date Comments C2406M 11/99 Original version. 1/00 Revised installation instructions. Added FCC notices. C2406M-A 2/00 Added varifocal lens. Changed format. C2406M-B 11/00 New camera module design, revised installation instructions.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
デバイスPelco C2406M-Fの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco C2406M-Fをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C2406M-Fの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C2406M-Fの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C2406M-Fで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C2406M-Fを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C2406M-Fの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C2406M-Fに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C2406M-Fデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。