PelcoメーカーC2461M-Aの使用説明書/サービス説明書
ページ先へ移動 of 16
150 Series Camclosure ® Integrated Camera System with LowLight ™ DSS T echnology C2461M-A (7/03) ® INST ALLA TION/OPERA TION In-Ceiling Mount.
2 C2461M-A (7/03) CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ..................................................................................... 3 WELCOME ................................................................................
C2461M-A (7/03) 3 Heater elements could be hot! When camera power is on, use caution when adjusting the camera. CAUTION IMPORT ANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.
4 C2461M-A (7/03) WELCOME Thank you for purchasing Pelco’ s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology . Y our new ICS150 Series in-ceiling dome system includes a high- resolution, low light, color camera with auto iris and varifocal lens.
C2461M-A (7/03) 5 INST ALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit. Remove the lower dome and place it to the side.
6 C2461M-A (7/03) Attach to a 4S Deep Electrical Box Refer to Figure 2 for the following steps. The installation instructions assume that the 4S box was previously installed. 1. Attach adapter plate to the 4S box with the two 8-32 x .750-inch screws supplied.
C2461M-A (7/03) 7 Install in a Ceiling T ile Refer to Figure 3 for the following steps. 1. Cut a hole 3.5 inches (9 cm) in diameter in the ceiling tile for the back box. Use the adapter plate as a template. 2. Punch four screw holes in the ceiling tile.
8 C2461M-A (7/03) Figure 4. Heater Jumper and Camera Connector Locations INST ALL THE CAMERA MODULE CHECK HEA TER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not require this heater . If the unit will never be subjected to a frost temperature, you can disable the heater , saving power requirements.
C2461M-A (7/03) 9 Wall Mounting - The camera bracket tab points out of the enclosure and the top of the camera points up towards the tab. Ceiling Mounting - The camera bracket tab points out of the enclosure and the top of the camera is pointed in the opposite direction.
10 C2461M-A (7/03) Figure 5. Default Switch Settings and Location of Camera Adjustments ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring clockwise/counterclockwise. Refer to Figure 5. 2. T ighten the zoom locking screw . 3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise.
C2461M-A (7/03) 11 ON OFF DIGIT AL SLOW SHUTTER (DSS) Digital slow shutter slows the picture frame rate and increases the camera sensitivity under low light conditions.
12 C2461M-A (7/03) VERTICAL PHASE ADJUSTMENT (24 V AC OPERA TION ONL Y) When using more than one camera power supply , a brief vertical roll may occur on the monitor when a camera view is switched. T o eliminate ver tical roll reverse the 24 VAC connections on one camera.
C2461M-A (7/03) 13 Figure 6. Dome and Trim Ring Installation REINST ALL THE DOME AND TRIM RING Place the trim ring and dome over the back box. If the dome has a liner , position the viewing window over the lens of the camera. T ighten the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit.
14 C2461M-A (7/03) SPECIFICA TIONS BACKBOX Electrical Input V oltage: 12 VDC or 24 V AC, ± 10%, auto-sensing Power Consumption: 13 watts or less Video Connector: BNC General Operating T emperature: -.
C2461M-A (7/03) 15 REVISION HISTORY Manual # Date Comments C2461M 4/03 Preliminary manual for beta testing. C2461M-A 7/03 Final version. ® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. © Copyright 2003, Pelco.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
デバイスPelco C2461M-Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco C2461M-Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C2461M-Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C2461M-Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C2461M-Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C2461M-Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C2461M-Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C2461M-Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C2461M-Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。