Pelcoメーカーc2462m-eの使用説明書/サービス説明書
ページ先へ移動 of 24
INST ALLA TION C2462M-E (3/09) 090 Series Camclosure ® Indoor Integrated Camera System Surface Mount/In-Ceiling.
2 C2462M-E (3/09) Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . .
C2462M-E (3/09) 3 List of Illustrations 1 Removing the Dome Bubble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Ceiling/W all In stallation . . . . . . . . . . . . . . . . . . . .
4 C2462M-E (3/09) Important Safety Instructions 1. Installation and servicing should be d one only by qualified service personnel and conform to all local codes.
C2462M-E (3/0 9) 5 Description The ICS090 Series Camclosure ® integrated camera system integrates a camera and lens package in a small, discreet dome.
6 C2462M-E (3/09) Remove the Dome Bubble T urn the dome bubble counterclockwise and lift (refer to Figure 1 ). Place the bubble on a non abrasive surface. Figure 1. Removing the Dome Bubb le If the unit is supplied with a dome liner , remove the li n er before installing the unit.
C2462M-E (3/0 9) 7 Installation The installation methods for the ICS090 Series include the following options: • Mount to the surface of a ceiling or wall • Install in a suspended ceiling • Insta.
8 C2462M-E (3/09) 4. Use 6-32 toggle bolts (not supplied) to attach the surface mount ring and back box to the mounting surface (refer to Figure 2 ). Figure 3. Concrete Ceiling/W all Installation Figure 2. Ceiling/Wall Installati on NOTE: For a concrete ceiling or wall installation, use 8-32 mounting hardware (not supplied), ref er to Figure 3.
C2462M-E (3/0 9) 9 IN-CEILING INSTALLATION: SUSPENDED CEILING 1. Remove the ceiling tile from the ceiling (refer to Figure 4 ). 2. Cut a 4-inch diameter h ole in the ceiling tile. 3. Remove the surface mount ring from the back box (refer to Figure 5 on page 10 ): a.
Figure 5. How to Remove Surfac e Mount Ring from Back Box 10 C2462M-E (3/09) AC operation only: If you are wiring more than one Camclosure to the same transformer , connect one side of the transformer to the red wire on all uni ts; connect the other side of the transformer to the black wire on all units.
C2462M-E (3/0 9) 11 IN-CEILING INSTALLATION: FIXED CEILING OR WALL 1. Cut a 4-inch diameter h ole in the ceiling/wall (refer to Figure 6 on p age 11 ). 2. Remove the surface mount ring from the back box (refer to Figure 5 on page 10 ). a. Place your fingers on the circular marks loca ted on the s ides of the surface mount ring.
12 C2462M-E (3/09) SURFACE INSTALLATION: 4S STANDARD ELECTRICAL BOX 1. Attach the adapter ring to the 4S box with tw o 8-32 x 1.00-inch screws (supplied; refer to Figure 7 ). 2. Connect the video cable and wires. BNC: Connect the BNC connector from the Camclosure to a mating BNC connector .
C2462M-E (3/0 9) 13 IN-CEILING INSTALLATION: 4S DEEP ELECTRICAL BOX 1. Remove the surface mount ring from the back box (refer to Figure 8 ): a. Place your fingers on the circular marks loca ted on the s ides of the surface mount ring. b. Pinch the sides.
14 C2462M-E (3/09) Camera Positioning Figure 9. Positioning the Camera Manually rotate and tilt the came ra module to position th e camera. Do not over-rot ate the module. WAR NI NG : E xcessively turning the module in one direct ion could result in damage to the wiring.
C2462M-E (3/0 9) 15 Camera Adjustments SWITCH SETTINGS FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to the switch drawing. The switch is located n ext to the lens.
16 C2462M-E (3/09) FOCUS ADJUSTMENT NOTE: Y o u will need a miniature Phillips or flat-tip screw driver to loosen and tighten the locking screw. T o adjust the fo cus: 1. Loosen the focus locking screw . 2. Position the inverted dome appro ximately 0.
C2462M-E (3/0 9) 17 V ERTICAL PHASE ADJUSTMENT (24 V ac Operation Only) When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. T o elim inate vertica l roll, reverse the 24 V AC connections on one camera.
18 C2462M-E (3/09) Install Liner and Bubble DOME LINER INSTALLATION If the unit is supplied with a dome liner , reinstall th e liner be fore installing the dome bubble (refer to Figure 13 ): 1. Align the studs located on the camera module with the clips on the liner .
C2462M-E (3/0 9) 19 DOME BUBBLE INSTALLATION T o install the d ome bubble (refer to Figure 14 ): 1. Select the bubble (clear or smoked). 2. Align the standoffs of the bubble with the slots of the back box. Figure 14. Installing the Dome Bubble 3. T urn the bubble clockwise until it locks in place.
20 C2462M-E (3/09) Service Connector An optional 4-foot service/monitor cable, part numb er ICS090-SC, is available for on- site setup and adjustments. T o use the cable, simply plug one end of the cable directly into the service connector of the ICS090, and then connect the other end to any st andard BNC (VIDEO IN) connector on a monitor .
C2462M-E (3/09) 21 Specifications ELECTRICAL Input V oltage* 12 VDC or 24 V AC (±10%), autosensing Power Consumption 3 W or less Video Connector BNC *24 V AC power is recommended when installing any Camclosure integrated camera system under fluorescent lighting conditions.
22 C2462M-E (3/09) REVISION HISTORY Manual # Date Comments C2462M 11/02 Original version. C2462M-A 1/03 Added Regulatory Noti ces for FCC Class B. C2462M-B 10/05 Revised switch-set ting descript ions for vari focal lens. Adde d WEEE statement. C2462M-C 1/06 Updated factory sw itch setting s for varifo cal lens per ECO 13164.
The materials us ed in the manufactu re of this documen t and its component s are compliant to th e requirement s of Directive 20 02/95/EC. This equipment co ntains electr ical or electron ic componen.
Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .
デバイスPelco c2462m-eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco c2462m-eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco c2462m-eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco c2462m-eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco c2462m-eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco c2462m-eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco c2462m-eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco c2462m-eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco c2462m-eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。