PelcoメーカーC493M-Gの使用説明書/サービス説明書
ページ先へ移動 of 16
HS1500 High-Security Enclosure INSTALLATION C493M-G (11/97).
.
C493M-G (11/97) 3 Contents Important Safeguards and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . .
4 C493M-G (11/97) Important Safeguards and W arnings Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
C493M-G (11/97) 5 Description The HS1500 is a high security camera enclosure of medium size designed for indoor “corner mount” installation for such applications as elevators, parking garages, classrooms, detention cells, etc., requiring maximum protection from vandalism in an unobtrusive package.
6 C493M-G (11/97) Installation NOTE: The four (4) fasteners required to secure the HS1500 to a wall (minimum 3/8” diameter recommended) are not supplied. Before installing the HS1500 to a wall, make certain that the mounting surface is able to support the full weight of the enclosure plus the camera and lens.
C493M-G (11/97) 7 (.
8 C493M-G (11/97) (This page intentionally left blank).
C493M-G (11/97) 9 HB1500/HB1524 HEATER/BLOWER KIT The HB1500/HB1524 heater/blower kits require either 120 V AC or 24 V AC, respectively . The heater provides 80 watts of heat and is thermostatically controlled to turn on at 40°F (4.44°C) and turn off at 60°F (15.
10 C493M-G (11/97) HEATER/BLOWER KIT INSTALLATION T o install the HB1500/HB1524 heater/blower kit, perform the following steps: 1. Remove the cover (Figure 5, item 4). 2. Attach the heater pads to each side of the mounting frame, below the tilt table assembly .
C493M-G (11/97) 11 T AMPER SWITCH INSTALLATION The HS1500 enclosure comes standard from the factory with a tamper switch installed. Should it become necessary to install a replacement switch, refer to Figure 4 for the correct position of the bracket/switch and perform the following steps: 1.
12 C493M-G (11/97) Exploded Assembly Diagram Figure 5. HS1500 Enclosure Exploded Assembly Diagram T able A. HS1500 Enclosure Exploded Assembly Parts Lists Item No. Qty Description Part Number 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 1 1 Bracket, switch, break-in Window , 10" x 9" x .
C493M-G (11/97) 13 Specifications MECHANICAL Window 1/2" (12.7 mm) thick impact and abrasion resistant clear Lexan Camera Mounting Adjustable tilt table Maximum Camera/Lens Size Accepts camera/lens combinations (including BNC connector) up to: 8.
14 C493M-G (11/97).
PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
デバイスPelco C493M-Gの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco C493M-Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C493M-Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C493M-Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C493M-Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C493M-Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C493M-Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C493M-Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C493M-Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。