PelcoメーカーC580Mの使用説明書/サービス説明書
ページ先へ移動 of 20
PT506-24DT Pan/Tilt Lens Control PT506-24A Auto/Random Scan Control Installation/ Operation Manual C580M Rev D (9/97) ® Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.
18 Pelco Manual C580M Rev D (9/97) ii CONTENTS Section Page 1.0 GENERAL .................................................................................................. 1 1.1 IMPORT ANT SAFEGUARDS AND WARNINGS ............................... 1 2.0 DESCRIPTION .
Pelco Manual C580M Rev D (9/97) 19 LIST OF ILLUSTRA TIONS Figur e Page 1 PT506-24DT Basic System Configuration ......................................... 3 2 PT506-24DT Configured with PT506-24A ......................................... 4 3 PT506-24DT Configured with a Relay Box .
20 Pelco Manual C580M Rev D (9/97) (This page intentionally left blank.) iv.
Pelco Manual C580M Rev D (9/97) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed.
2 Pelco Manual C580M Rev D (9/97) 2.0 DESCRIPTION The PT506-24DT is a pan/tilt and lens control designed to remotely operate 24 V AC pan/tilts and all Pelco motorized zoom lenses. This unit can control up to six (6) different locations, all of which can be selected by pressing the corresponding illu- minated push-button switch.
Pelco Manual C580M Rev D (9/97) 3 3.0 INST ALLA TION Figure 1 shows a typical rear panel installation of the PT506-24DT controller . The distance from the controller is limited by the wire size and pan/tilt used. (See Sec- tion 3.1 Recommended Cable Distances.
4 Pelco Manual C580M Rev D (9/97) Figure 2. PT506-24DT Configured with PT506-24A Figure 3. PT506-24DT Configured with a Relay Box.
Pelco Manual C580M Rev D (9/97) 5 3.2 CONNECTOR ASSEMBL Y Assemble the connector parts according to the instructions below . Detail B, below , reflects the pin arrangement specific to all PT506-24DT Pan/T ilt and Lens Control and the PT506-24A Auto/Random Scan Control.
6 Pelco Manual C580M Rev D (9/97) 4.0 OPERA TION The PT506-24DT will not allow control of any of the six pan/tilt stations until one is selected by pressing the desired station on the latching selection switches. Once a selection has been made, the switch will illuminate and all control functions will be available only to that particular station.
Pelco Manual C580M Rev D (9/97) 7 4.2 OPERA TIONAL TEST — PT506-24A The PT506-24A will add two modes of automatic pan operation to the PT506-24DT . Once the PT506-24A is interconnected as shown in Figure 2, apply power to the units.
8 Pelco Manual C580M Rev D (9/97) 5.0 MAINTENANCE Under normal operating conditions and usage, maintenance of this equipment is not necessary . However , if maintenance is required, repairs should be performed by a qualified service technician or equipment should be returned to the factory for repair .
Pelco Manual C580M Rev D (9/97) 9 6.0 SCHEMA TICS If necessary , refer to the following schematics for troubleshooting or repair Figure 5. PT506-24DT Schematics (Sheet 1 of 5).
10 Pelco Manual C580M Rev D (9/97) Figure 5. PT506-24DT Schematics (Sheet 2 of 5).
Pelco Manual C580M Rev D (9/97) 11 Figure 5. PT506-24DT Schematics (Sheet 3 of 5).
12 Pelco Manual C580M Rev D (9/97) Figure 5. PT506-24DT Schematics (Sheet 4 of 5).
Pelco Manual C580M Rev D (9/97) 13 Figure 5. PT506-24DT Schematics (Sheet 5 of 5).
14 Pelco Manual C580M Rev D (9/97) 7.0 SPECIFICA TIONS ELECTRICAL PT506-24DT Input Voltage: 120 VAC, 50/60 Hz (230 VAC optional) Output Voltage: 24 VAC, 60 Hz pan/tilt supply 0 to ± 9 VDC lens supply Power Requirement: 1.
Pelco Manual C580M Rev D (9/97) 15 GENERAL Enclosure Construction Panel: Aluminum Cover: Steel, textured black enamel Chassis: Steel, galvanized Temperature Range: 32 ° to 120 ° F (0 ° to 50 ° C) Size: See Figure 6 Weight PT506-24DT 13 lbs 6 oz (6 kg) PT506-24A 18 lbs (8.
16 Pelco Manual C580M Rev D (9/97) 8.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1997, Pelco. All rights reserved.
デバイスPelco C580Mの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco C580Mをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C580Mの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C580Mの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C580Mで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C580Mを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C580Mの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C580Mに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C580Mデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。