PelcoメーカーCCC5100Hの使用説明書/サービス説明書
ページ先へ移動 of 16
QUICK START GUIDE C2910M-B- Q S (2/06) CCC5100H Series Camera.
2 C2910M-B-QS (2/06) This quick start guide describes how to install and confi gure the CCC5100H Series camera in most applications. It contains a representation of the setup menus to help you locate and change specific settings.
C2910M-B-QS (2/06) 3 H AR DW AR E Refer to Figure 1 as you install the CCC5100H Series camera. Figure 1. CCC5100H Connectors VIDEO CONNECTOR SERVICE CONNECTOR SETUP BUTTONS MULTIFUNCTION (RJ45-10) CON.
4 C2910M-B-QS (2/06) LENS The CCC5100H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. The camera accepts both CS- and C-mount lenses without an adapter . T o mount the lens onto the camera: 1.
C2910M-B-QS (2/06) 5 CONNECTIONS The CCC5100H Series camera offers standard power and coax video connectors. T o use the RJ45-10 multifunction connector that combines power, video, and control leads, refer to Multifunction Connector in the Installation/Operation manual.
6 C2910M-B-QS (2/06) SETUP MENUS Use the setup menus to customize the camera settings. Refer to the setup menus as shown on this and the opposite page: CAMERA DISPLAY CAMERA NAME CCC5100H RX ADDRESS 1.
C2910M-B-QS (2/06) 7 WHITE BALANCE MODE ATW NORMAL <ATW NORMAL /DESAT> <MANUAL RED/BLUE> <MANUAL COLOR TEMP> BACK EXIT ATW NORMAL /DESAT LOW LIMIT HIGH LIMIT BACK EXIT |------+------| |------+------| 2k 5.5k 5.5k 11k PROFILES ACTIVE WDR SAVE AS CUSTOM1 DEFAULT WDR BACK EXIT SYSTEM INFORMATION FIRMWARE VER.
8 C2910M-B-QS (2/06) A CCESSING THE SETUP MENUS Use the top, center , and bottom buttons on the rear panel to access and navigate the setup menus. T able A lists the button presses for each menu action. A short press is less than one second; a long press is more than one second.
C2910M-B-QS (2/06) 9 C A ME RA P R OFILE Select a basic camera profile and then customize it. After you save your custom camera settings into a user-definable profile, change the default to CUSTOM1 or CUSTOM2. C A UTION: Be sure to save all camera settings into a user-definable profile so they will not be lost in case the camera loses power .
10 C2910M-B-QS (2/06) 4. Select the user-definable profile to use during power -up: a. Select DEFAUL T and press the center button. b. Press the top or bottom button to select your profi le: CUSTOM1 or CUSTOM2. c. Press the center button to set the new default profi le.
C2910M-B-QS (2/06) 11 DC-D R IVE A UTO I R IS LENS SETUP Before using a DC-drive auto iris lens, you must adjust the DC offset setting. Use the following steps to match the camera’ s DC voltage setting to the drive circuit on the auto iris lens: 1. Remove the lens from the camera.
12 C2910M-B-QS (2/06) 9. Hold the auto iris lens so you can watch the iris (refer to Figure 3). Then increase the DC OFFSET setting slowly until the iris closes. Figure 3. Open Iris and Closed Iris 10. As soon as the iris closes, slowly decrease the DC OFFSET value by 14, or until the iris opens again.
C2910M-B-QS (2/06) 13 LENS FOCUS Focus the camera lens. 1. A uto iris only: Cover the auto iris lens with a suitable neutral density (ND) filter to open the iris fully . For best results, use an ND3 filter . 2. Manual iris only: Open the iris completely .
14 C2910M-B-QS (2/06) 6. Fixed focal length lens only: a. Set the lens focal length to far ( ∞ ). b. Adjust the back focus. Move the back focus locking screw on the camera up or down until the image is focused. As the focus improves, the value on the FINE FOCUS menu increases: the higher the number, the better the focus.
C2910M-B-QS (2/06) 15 R evision History Manual No. Date Comments C2910M-QS 9/04 Original version. C2910M-A-QS 4/05 Updated for RGB filters, new firmware. C2910M-B-QS 2/06 Removed the high voltage and RGB models. Updated the OSD version. Changed the active profile default.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
デバイスPelco CCC5100Hの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco CCC5100Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco CCC5100Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco CCC5100Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco CCC5100Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco CCC5100Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco CCC5100Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco CCC5100Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco CCC5100Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。