PelcoメーカーDX9200HDDIの使用説明書/サービス説明書
ページ先へ移動 of 20
DX9200HDDI Series IDE V ideo Storage Unit C637M-B (10/03) ® INST ALLA TION/OPERA TION.
CONTENTS Section Page REGULA TOR Y NOTICES ............................................................................................................. ......................................................................................... 3 RADIO AND TELEVISION INTERFERENCE .
C637M-B (10/03) 3 REGULA TORY NOTICES This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
4 C637M-B (10/03) IMPORT ANT SAFEGUARDS AND W ARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
C637M-B (10/03) 5 DESCRIPTION The DX9200HDDI video storage unit is one of the components of the DX9000 system. The storage unit contains up to 14 IDE hard disk drives for storing video information from the DX9000 recorder . Up to four IDE storage units can be connected to a recorder .
6 C637M-B (10/03) FRONT VIEW Figure 1 shows the features on the front of the IDE storage unit. Figure 1. Front View 1. Panel: Use the features of this panel to view the configuration of the RAID or to enter the environment menu. Y ou must lower this panel to remove or add hard drives.
C637M-B (10/03) 7 11. Up arrow/Quit button: Used in conjunction with the Controller and ENC buttons. Press to scroll through the information on the LCD display , to move through each menu, or to go back to the previous menu. 12. Down arrow/Info button: Used in conjunction with the Controller and ENC buttons.
8 C637M-B (10/03) INST ALLA TION Make sure the following parts are supplied with the storage unit. 1V ideo Storage Unit with IDE hard drives 2 Power cords (1 USA standard and 1 European standard) 2 External SCSI cables 2 Active terminators (for connecting to SCSI channels) 2 Brackets 6 Screws, M4 x .
C637M-B (10/03) 9 MOUNTING The storage unit can be placed on a flat surface, such as a shelf, or it can be installed in a 19-inch (48.26 cm) wide equipment rack. NOTE: Allow one rack unit (1.75 inches or 4.5 cm) of space above the storage unit for air circulation.
10 C637M-B (10/03) STORAGE RECORDER A HOST B HOST A CHANNEL A SCSI CABLE STORAGE RECORDER A RECORDER B HOST B HOST A CHANNEL A CHANNEL A SCSI CABLE SCSI CABLE Figure 5. One Storage Unit/Two Recorder Configuration HARDWARE CONNECTIONS There are five hardware configurations.
C637M-B (10/03) 11 CHANNEL A CHANNEL B STORAGE B STORAGE A RECORDER HOST A HOST A SCSI CABLE SCSI CABLE CONNECTING TWO STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder .
12 C637M-B (10/03) Figure 7. Three Storage Unit/One Recorder Configuration CONNECTING THREE STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder .
C637M-B (10/03) 13 CONNECTING FOUR STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder . 3. Connect a SCSI cable (DX9200HDDI-LCBL) from the Host A Out port on Storage A to the Host A In port on Storage C.
14 C637M-B (10/03) OPERA TION The storage unit has been preconfigured to operate using RAID Level 5 or RAID Level 5+1 technology . Pelco recommends RAID Level 5+1.
C637M-B (10/03) 15 TROUBLESHOOTING What do I do when the voltage warning LED illuminates red and an alarm sounds? This happens when the output DC voltage is under 4.5V or over 5.5V , and under 10.2V or over 13.8V . The ENC global fault LED also illuminates.
16 C637M-B (10/03) SERVICE HOW TO REPLACE A F AN The fans are hot-swappable. The spare part number for the fan is DX9200HDDI-F AN. THUMBSCREW HANDLE THUMBSCRE W HANDLE Figure 9. Replacing a Fan Figure 10. Replacing a Power Supply 1. Loosen the thumbscrew .
C637M-B (10/03) 17 HOW TO CHANGE FROM RAID 5 TO RAID 5+1 To change a RAID 5 configuration to a RAID 5+1 configuration, you must add a hot spar e hard drive. A hot spare hard drive becomes the replacement hard drive when a hard drive fails in the RAID 5+1 configuration.
POWER CONNECTOR 40-PIN ATA CABLE CONNECTOR LEVER RELEASE LEVER ATA CABLE CONNECTOR PORT JUMPER POWER PORT PHILLIPS SCREWS TRAY WITH HARD DRIVE Figure 11.
W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
デバイスPelco DX9200HDDIの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco DX9200HDDIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco DX9200HDDIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco DX9200HDDIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco DX9200HDDIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco DX9200HDDIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco DX9200HDDIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco DX9200HDDIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco DX9200HDDIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。