PelcoメーカーERD2000の使用説明書/サービス説明書
ページ先へ移動 of 16
IRD/ERD2000 Series Receiver C1506M-A (8/02) ® INST ALLA TION/OPERA TION.
2 C1506M-A (8/02).
C1506M-A (8/02) 3 CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ..................................................................................... 4 DESCRIPTION ............................................................................
4 C1506M-A (8/02) 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings.
C1506M-A (8/02) 5 The IRD/ERD2000 Series Receiver operates Pelco’ s fixed speed pan/tilts and domes. The receiver works with standard and extended Coaxitron ® controllers, including the CM6700/ 7500/8500/9500, KBD9000, MPT9000/9008/9500, and MX4000.
6 C1506M-A (8/02) ERD2200 WIRING E N C L O S U R E POWER O U T L L N N GROUND STUD POWER TERMINALS M A I N POW E R IN Figure 2. ERD2200 Receiver Figure 3. ERD2200 Power Connections 1. Fuses are installed for 115 V AC operation. For 230 V AC operation, install the appropriate fuses (supplied).
C1506M-A (8/02) 7 A C A C 24V 50/60HZ INPUT POWER ~ 24V ~ 50/60HZ P/T POWER SELECT 115 /230V ~ 50/60HZ A C A C ERD OPTION TLC OUT VIDEO IN PWR CX LENS AUX1 AUX2 C N N OC 24V ,1A ~ I F Z C CAM PWR C C PA N/ T I LT 5V CLASS 2 WIRING ERD OPTIONS 11 5/230V 50/60Hz .
8 C1506M-A (8/02) IRD2024 WIRING 1. Connect power to the 24 V AC INPUT connector on the rear of the receiver . The receiver’ s power requirement is a maximum of 5 V A, not including the camera and pan/tilt. Refer to the pan/tilt manual for its power requirements.
C1506M-A (8/02) 9 When power is applied to the receiver , the green PWR LED on the receiver lights. Whenever the receiver gets a valid Coaxitron control signal, the green CX LED blinks.
10 C1506M-A (8/02) FUSE REPLACEMENT CAUTION: These service instructions are for use by qualified service personnel only . T o reduce the risk of electrical shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
C1506M-A (8/02) 11 TROUBLESHOOTING Check the wiring connections. If the CX LED does not blink when commands are sent to the receiver , make sure the controller is working properly . Also check the video coaxial cable between the controller and the VIDEO OUT connection on the receiver .
12 C1506M-A (8/02) WIRING T ABLES Wire Gauge Table A. 24 VAC Wiring Distances Table The following are the recommended maximum wire distances (transformer to load) for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.
C1506M-A (8/02) 13 SPECIFICA TIONS ERD2200 Electrical Input V oltage: 115/230 V AC, 50/60 Hz Output V oltage Camera: 24 V AC (or 115/230 VAC if using enclosure power) Lens: 8 VDC Pan/T ilt: 24/115/230.
14 C1506M-A (8/02) REGULA TORY NOTICES NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
C1506M-A (8/02) 15 REVISION HISTORY Manual # Date Comments C1506M 3/00 Original version. C1506M-A 8/02 Revised manual per ECO #02-8195 to meet UL standards. Added FCC notice. W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
デバイスPelco ERD2000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco ERD2000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco ERD2000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco ERD2000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco ERD2000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco ERD2000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco ERD2000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco ERD2000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco ERD2000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。