PelcoメーカーFR82041の使用説明書/サービス説明書
ページ先へ移動 of 28
® INST ALLA TION F T82041/FR82041 Unmanaged Ethernet Switch Four 10BASE-T/100BASE-TX Ports and One 100BASE-FX Fiber Port C2623M (2/07).
.
C2623M (2/0 7) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Not ices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C2623M (2/07) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
C2623M (2/0 7) 5 The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
6 C2623M (2/07) Regulatory Notices This device complies with Part 15 of the FCC Rule s. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation.
C2623M (2/0 7) 7 Product Overview DESCRIPTION The F T82041/FR82041 unmanag ed Ethernet switch provid es four 10BASE-T/100BASE-TX ports and one 100BASE-FX fiber port for the trans port of bidirectional Ethernet data.
8 C2623M (2/07) • Designed to meet NEMA TS 2 and Caltrans traff ic signal control equipment standards for ambient operating temperature, mechanical shock and vibrati on, humidity with condensation, .
C2623M (2/0 7) 9 OPTIONAL ACCESSORIES The following optional a ccessories are available: WM5001-3U Wall mount base ki t for single-width module WM5001-3UEXP Wall mount expansion kit for single-width m.
10 C2623M (2/07) REAR PANEL Figure 3 illustrates the rear pa nel of the F T82041 and FR82041 modules. Figure 3. Rear Panel of F T82041 and FR82041 Mo dules (SC Fiber Connector Shown) For additional information about r ear -panel connections, refer to Installation on page 11.
C2623M (2/0 7) 11 Installation PACKAGE CONTENTS The following it ems are supplied: 1 F T82041 or FR82041 module 1 Regulated switching power suppl y with four plug adapt ers (North American, Australian, U.K., and European configurations); 100-240 V A C, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4-40 x 0.
12 C2623M (2/07) Using the TX Mode switch for a parti cular port, y ou can do the following: • Enable autonegotiation or select (force) a specific data rate and duplex mode: – Enabling autonegotia.
C2623M (2/0 7) 13 NOTE: TX Mode configuration must be set when the module is powered off. If you wish to change a TX Mode switch setting after the module has been powered on, power of f the module, change the TX Mode switch setting, and then power on the module again.
14 C2623M (2/07) Mounting the F T82041/FR82041 Module Using the Wall Clip NOTE: Before mounting the F T82041/FR82041 module to a wall, ensure that there is adequate space at both ends for viewing the fr ont-panel LEDs and for making the various rear-pa nel cable connec- tions.
C2623M (2/0 7) 15 CONNECTIONS Connections to the F T82041/FR82041 module are made on the rear panel of the unit (refer to Figure 6). Figure 6. F T82041/FR82041 Module Connecti ons As illustrated in Fi.
16 C2623M (2/07) • Fiber connection NOTE: Fiber port A of the F T82041 module connects to fiber port B of the FR82041 module or of any other Pelco Ethernet sw itch that supports wavelength division multiplexing (WDM).
C2623M (2/0 7) 17 T roubleshooting LED indicators on the front and rear panels of the F T82041/FR82041 module allow you to monitor operational status: • LED indicators on the front panel allow you to monitor operating power , 100BASE-FX port status, and optic signal/l aser status.
18 C2623M (2/07) Optic Fault LED ( ) Green The optical signal is being received and laser is operating properly . — No action is required. Red The optical signal is not being received. Remote module is not powered on. Check power connections. Replace power supply if necessary .
C2623M (2/0 7) 19 T able C. T roubleshooting with Rear -Panel Indicators Indicator Color Meaning Possibl e Cause Corrective Action RJ-45 10BASE-T/100BASE-TX Port Stat us LED - Left (Link / Activity) Amber A 10BASE-T link is established. — If 10BASE-T operation is desired, no action is required.
20 C2623M (2/07) RJ-45 10BASE-T/100BASE-TX Port Status LED - Left (Link/Activity) (Continued) Not lit A 10BASE-T or 100BASE-TX link cannot be estab- lished. A problem may exist with the cable: • Cable is not connected to the module or to the 10BASE-T/100BASE-TX compatible device.
C2623M (2/0 7) 21 RJ-45 10BASE-T/100BASE-TX Port St atus LED - Right (Duplex/Collision) Amber Port is set to 10BASE-T full- duplex mode. — If 10BASE-T full-duplex opera- tion is desired, no action is required.
22 C2623M (2/07) RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Green Port is set to 100BASE-TX full- duplex mode. — If 100BASE-TX full-duplex operation is desired, no action is required.
C2623M (2/0 7) 23 RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Not lit Port is set to 10BASE-T half- duplex mode and no collisions are detected.* — If 10BASE-T half-duplex operation is desired, no action is required.
24 C2623M (2/07) Specifications PERFORMANCE Switch T ype Unmanaged Layer 2 Switch Method Store and forward Switch Fabric Non-head-of-line blocking Data Rate 10/100 Mbps Compliance IEEE 802.
C2623M (2/0 7) 25 OPTICAL POWER BUDGET AND MAXI MUM TRANSMISSION DIST ANCE Model Number Wavelength (T ransmit/Receive)* Optical Power Budget Maximum T ransmission Distance T ransmitter End Receiver End Fiber Port A Fiber Port B Multimode (62.5/125 μm) F T82041MSTR-1 FR82041MSTR-1 1310/850 nm 850/1310 nm 26 dB † 2 km (1.
26 C2623M (2/07) Appendix. RJ-45 Connector Pinouts Figure 7 illustrates RJ-45 MDI/MDI-X connector pinouts. Figure 7. RJ-45 MDI/MDI-X Connector Pinouts T able D summarizes RJ-45 MDI/MDI-X connector pinouts.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment.
® Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
デバイスPelco FR82041の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco FR82041をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco FR82041の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco FR82041の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco FR82041で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco FR82041を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco FR82041の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco FR82041に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco FR82041デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。