PelcoメーカーFT8301Aの使用説明書/サービス説明書
ページ先へ移動 of 36
INST ALLA TION F T8301A Miniature Fiber T ransmitter Single-Channel Digitally Encoded Video C1680M (1/06).
.
C1680M (1/06) 3 Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C1680M (1/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
C1680M (1/06) 5 The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
6 C1680M (1/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation.
C1680M (1/06) 7 Product Overview DESCRIPTION The F T8301A miniature fiber transmitter provides the ability to transmit one composite video channel over one optical fiber . The F T8301A transmitter is compatible with the single-channel F R8301A and dual-channel FR8302A receivers.
8 C1680M (1/06) Figure 1. Single-Channel V ideo T ransmission Using F T8301A T ransmitter ONE VIDEO OUTPUT COMPATIBLE RECEIVER ONE FIBER DF5/DF8 FIXED MOUNT DOME FT8 3 01A TRANSMITTER ONE VIDEO OUTPUT.
C1680M (1/06) 9 FRONT PANEL The front panel of the F T8301A transmi tter provides connectors and LED indicators (refer to Figure 2). Figure 2. Front Panel of F T8301A T ransmitter—Multimode and Single-Mode Models NOTE: The F T8301A transmitter provides two video input connectors: one UTP connector and one BNC connector .
10 C1680M (1/06) Installation PACKAGE CONTENTS The following it ems are supplied: 1 F T8301A transmitter with attached left and right wall -mounting brackets 1 Regulated switching power suppl y with four plug adapt ers (North American, Australian, U.K.
C1680M (1/06) 11 CONNECTIONS Before mounting the F T8301A transmitter , note t he following transmitter connections (refer to Figure 3): • Power connection NOTES: – A 12 VDC or 24 VA C power supply can be us ed to power the trans mitter . A 12 VDC power supply is provided.
12 C1680M (1/06) Figure 3. F T8301A T ransmitter Connections POWER C ONNE C TION C OAXIAL C ABLE UTP WIRE S OR FIBER OPTI C C ABLE POWER C ONNE C TION C OAXIAL C ABLE UTP WIRE S OR MULTIMODE MODEL S S.
C1680M (1/06) 13 MOUNTING This section provides info rmation about the following: • Mounting the transmitter to a wall • Mounting the transmitter into an EH2515 Series enclosure • Mounting the t.
14 C1680M (1/06) MOUNTING THE T RANSMITTER INTO AN EH2515 SER IES ENCLOSURE The following procedure provides instructions to mount the F T8301A transmitter into an existing EH2515 Series enclosure installation. T o mount the transmitter into an EH2515 Series enclosure, do the following: 1.
C1680M (1/06) 15 Figure 5. Attaching EH2500 Bracket to F T8301A T ransmitter (2) SC REW S , 4-40 X 0.187-IN C H, PHILLIP S , FLAT HEAD EH2500 BRA C KET S IDE VIEW OF EH2500 BRA C KET WITH ATTA C HED F.
16 C1680M (1/06) Figure 6. Mounting F T8301A T ransmitter into EH2515 Enclosure S IDE VIEW OF EH2515 EN C LO S URE WITH FT8301A TRAN S MITTER IN S TALLED EH2500 BRA C KET WITH ATTA C HED FT8301A TRAN S MITTER EH2515 EN C LO S URE FT8301A TRAN S MITTER SC REW, 10-32 X 0.
C1680M (1/06) 17 7. Connect power , fiber optic, and video cables to the transmitter by doing the following: a. Insert the power cable through ei ther of the two gland connectors on the enclosure, route the cable underneath the transmitte r toward the power connector on the transmitter , and then connect the cable to the power connector .
18 C1680M (1/06) MOUNTING THE T RANSMITTER INTO AN EH3512/EH3515 SERIES ENCLOSURE The following procedure provides instructions to mount the F T8301A transmitter into an existing EH3512/EH3515 Series enclosure installation. T o mount the transmitter into an EH3512/EH 3515 Series enclosure, do the following: 1.
C1680M (1/06) 19 8. Do the following (refer to Figure 9): a. Using the replacement gland supplied in the EH3500 Series accessory kit, attach the gland to either of the cable entry holes on the enclosure. Note that the replacement gland is shorter than the two gl ands provided for the enclosure.
20 C1680M (1/06) Figure 10. Removing EH3512/EH3515 Enclosure Accessori es 10. Mount the transmitter into the enclosure by doing the following (refer to Figure 11): a. Position the transmitter at the rear of the enclosure with the connectors facing the camera.
C1680M (1/06) 21 Figure 11. Mounting F T8301A T ransmitter into EH3512/EH3515 Enclosure FT8301A TRAN S MITTER S IDE VIEW OF EH3512/EH3515 EN C LO S URE WITH FT8301A TRAN S MITTER IN S TALLED 6-32 C AP.
22 C1680M (1/06) 11. Connect power , fiber optic, and video cabli ng to the transmitter by doing the following: a. Insert the power cable through the gland or conduit on the bottom of the enclosure, and then connect the cable to the powe r connector on the transmitter .
C1680M (1/06) 23 Figure 13. Reinstalling EH3512/EH3515 Heater Bracket, Blo wer , and Heater Figure 14. Reinstalling EH3512/EH3515 PC Board (2) LO C K WA S HER S , #6 (2) SC REW S , 6-32 X 1.
24 C1680M (1/06) MOUNTING THE T RANSMITTER INTO A DF5/DF8 DOME The F T8301A transmitter can be mounted into DF5 and DF8 in-ceiling and pendan t fixed mount domes.
C1680M (1/06) 25 Mounting the T ransmitter into a DF5/DF8 In-Ceiling Dome The following procedure provides in structions to mount the F T8301A tr ansmitter into an existing DF5/ DF8 in-ceiling dom e installation. T o mount the transmitter into a DF5/ DF8 in-ceiling dome, do the following: 1.
26 C1680M (1/06) 8. Mount the transmitter into the back box as follows (ref er to Figure 17): NOTE: In Figure 17, the pan bracket is removed from t he back box for illustration purposes only . Y ou do not need to remove the pan bracket from the back box.
C1680M (1/06) 27 9. Connect the transmitter as follows: a. Connect power to the transmitter . b. Route the fiber optic cable around the inside of the back box toward the transmitter and connect the cable to the fiber opti c connector on the transmitter .
28 C1680M (1/06) Mounting the T ransmitter into a DF5/DF8 Pendant Dome The following procedure provides in structions to mount the F T8301A tr ansmitter into an existing DF5/ DF8 pendant dome installation. T o mount the transmitter into a DF 5/DF8 pendant dome, do the following: 1.
C1680M (1/06) 29 8. Mount the transmitter into the back box as follows (ref er to Figure 19): NOTE: In Figure 19, the pan bracket is removed from the back box for illustration purposes only . Y ou do not need to remove the pan bracket from the back box.
30 C1680M (1/06) 9. Connect the transmitter as follows: a. Connect power to the transmitter . b. Route the fiber optic cable around the inside of the back box toward the transmitter and connect the cable to the fiber opti c connector on the transmitter .
C1680M (1/06) 31 T roubleshooting LED indicators on the F T8301A transmitter (refer to Figure 2) allow you to m onito r signal status and laser status.
32 C1680M (1/06) Specifications VIDEO Number of Channels 1 Modulation T ype Pulse code m odulation, 8-bi t resolution Video Input BNC, 1.0 Vp-p, 75 ohms or UTP , 100 ohms; NTSC, P AL, and SECAM Bandwidth 6.
C1680M (1/06) 33 OPTICAL POWER BUDGET , TRANSMISSI ON DIST ANCE, AND LASER CLASS 1 LIMIT F T8301A Miniature T ransmitter Compatible Receivers Wavelength Optical Power Budget Maximum T ransmission Distance Laser Class 1 Limit* Multimode (62.5/125 µm) F T8301AMST FR8301AMSTR 850 nm 20 dB † 2 km (1.
34 C1680M (1/06) This equipment contains electrica l or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local de aler for procedures for recycling this equipment.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in ma terial or wor kmanship for a period of one year after the date of shipment. Exception s to this warrant y are as noted below: • Five years on F T/FR8000 Series fiber o ptic products.
United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
デバイスPelco FT8301Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco FT8301Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco FT8301Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco FT8301Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco FT8301Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco FT8301Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco FT8301Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco FT8301Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco FT8301Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。