PelcoメーカーIS90の使用説明書/サービス説明書
ページ先へ移動 of 36
INST ALLA TION C3425M-E (1/09) IS90 Series Camclosure ® Indoor Integrated Camera System.
.
C3425M-E (1/09) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C3425M-E (1/09) List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 Removing the Bubble . . . . . . . . . . . . . . . . . . . . . .
C3425M-E (1/09) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 C3425M-E (1/09) Description The IS90 Series Camclosure ® integrated camera system combines a camera and lens package in a small, discreet dome. The system is easy to install and can be mounted to the surface of a ceiling/wall or recessed in a ceiling/wall.
C3425M-E (1/09) 7 Indoor dome, surface/flush mount, smoked and clear bubble, black finish PARTS LIST Camera T ype Lens/Iris NTSC P AL Color , Wide Dynamic Range, Day/Night 3.0 to 9.5 mm, Day/Night V arifocal, Auto Iris IS90B-DWV9 9.0 to 22.0 mm, Day/N ight Varifocal, Auto Iris IS90B-DWV22 Color , High Resolution, Day/Night 3.
8 C3425M-E (1/09) Figure 1. Package Comp onents IS90 SERIES C AM C LOSURE WITH SMOKED BUBBLE LINER ADAPTER PLA TE C LEAR BUBBLE SHOWN A C TUAL SIZE SHIPPING BOX 8-32 X 1.00-IN C H PHILLIPS P AN HEAD S C REWS (2) 8-32 X 0.75-IN C H PHILLIPS P AN HEAD SELF-T APPING S C REWS (2) 8-32 X 2.
C3425M-E (1/09) 9 Remove the Bubble T urn the bubble counterclockwise and lift (refer to Figure 2). Place the bubble on a non abrasive surface. If the liner is already installed, remo ve it b efore installing the un it. T o remove th e liner , gently lift it from the unit.
10 C3425M-E (1/09) Installation Y ou can install the IS90 Series Camclosure integrated camera system as follows: • Mount to the surface of a ceiling/wall (refer to Surface Installation: Ceiling/Wall on page 10). • Install in a suspended ceiling (refer to In-Ceiling Installation: Suspended Ceiling o n page 12).
C3425M-E (1/09) 11 Figure 3. Ceiling/ Wall Installati on Figure 4. Concrete Ceil ing/ Wall Installation BA C K BOX AND SURFA C E MOUNT RING WAL L O R C EILING 6-32 TOGGLE BOL TS (NOT SUPPLIED) BA C K .
12 C3425M-E (1/09) IN-CEILING INSTALLATION: SUSPENDED CEILING 1. Remove the surfa ce mount ring from the b ack box (refer to Figure 5): a. Place fingers on the circular marks locate d on the sides of th e surface mount ring. b. Pinch the sides. c. Lift and remove the surface mount ring from the back box.
C3425M-E (1/09) 13 2. Pull the video and power wires to the selected ceiling tile. 3. Mount the unit to the ceiling tile (refer to Figure 6 and Figure 7): a. Remove the ceiling tile from the ceiling. b. Cut a hole 4 inches (10 cm) in diameter in the ceiling tile.
14 C3425M-E (1/09) 4. Remove an adjacent ceiling tile to access the unit. 5. Connect the video cable and wires: • BNC: Connect the BNC connector from th e unit to a ma ting BNC connector . • UTP: Connect the blue wire to Video +; connect the gray wire to V ideo -.
C3425M-E (1/09) 15 6. Attach the back box to the mounting surface: • If you have access behind the ceiling/wall (refer to Figure 6 on page 13): (1) Place the adapter plate on t he inside of the ceiling/wall. (2) Attach the back box to the ceiling/wall with two 10-32 x 1.
16 C3425M-E (1/09) 5. Attach the surface mount ring and back box to the adapter plate with two 8-32 x 2.50-inch Phillips pan head self-tapping screws (supplied). Figure 9. 4 S S tandard Electrical Bo x Installation IN-CEILING INSTALLATION: 4S DEEP ELECTRICAL BOX 1.
C3425M-E (1/09) 17 NOTE: Failure to connect all AC po wered units the sa me way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras. 6. Attach the back box to the adapter plate with two 8-32 x 0.
18 C3425M-E (1/09) Camera Adjustments T o perform the following camera adjustments, connect a monitor . Then turn on power to the camera and monitor . T o use the service connector , refer to Service Connector on page 30.
C3425M-E (1/09) 19 T o adjust the fo cus: 1. Loosen the focus locking screw . 2. Position the inverted dome appro ximately 0.125 inch (3.175 mm) from the front of the lens. Make sure that the lens and the dome are centered (refer to Figure 12). 3. T urn the focus locking screw clockwise or counterclockwise to adjust the focus.
20 C3425M-E (1/09) DN/CH/C SERIES ADJUSTMENTS Refer to Figure 13 to adjust the IS90-DN, IS90-CH, or IS90-C model. Figure 13. Adjusting the I S 90-DN/CH/C S eries Camclo sure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation.
C3425M-E (1/09) 21 SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flic kering can be caused by a number of conditions, including the qua lity of the source power and the age and type of fluorescent bulbs and ballasts.
22 C3425M-E (1/09) 3. Each time an adjustment is made, switch back a nd forth between the camera you are adju sting and the reference camera. Repeat this process as m any times as necessary until the roll betwe en the cameras is no longer noticeable. 4.
C3425M-E (1/09) 23 DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation.
24 C3425M-E (1/09) DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 15 to adjust the IS90-DW o r IS90-CW model. Figure 15. Adjusting the I S 90-DW/CW S eries Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation.
C3425M-E (1/09) 25 SW1-4: Auto White Balance/Ma nual White Balance Auto white balance (AWB) is enabled by default (ON). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video shows all white.
26 C3425M-E (1/09) SW1-8: Day/Night Operation (DW models only) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation.
C3425M-E (1/09) 27 AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS90-DW and IS90-CW Series Ca mclosures automatically adjust the camera to the auto iris. Auto iris level adjustments are not necessary. V ERTICAL PHASE ADJUSTMENT Use this procedure for 24 V AC ope ration only .
28 C3425M-E (1/09) Camera Positioning Rotate and tilt the camera module to position the camera. NOTE: Do not over -rotate the module. Excessively turni ng the module in one direction could result in damage to the wiring.
C3425M-E (1/09) 29 Install Liner and Bubble 1. T o install the liner with a clear bubble (refer to Figure 18): a. Align the studs located on the camera module with the clips on the liner . b. Lightly pinch the sides of the liner , opposite fro m the clips, and p lace the clips over the stud s.
30 C3425M-E (1/09) Service Connector The IS90 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to se t up the field of view and to focus the camera.
C3425M-E (1/09) 31 T o assemble the cable: 1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follo w the directions supplied with the mini ature coaxial connector . 2. Attach the 2.5 mm monaural plug to the other end of the coaxial cable (refer to Figure 21): a.
32 C3425M-E (1/09) Specifications GENERAL Pan/T ilt Adjustment Manual Pan 360° T ilt 140° (20° to 160° range) Rotation 360° Construction Back Box and Surface Mount Ring ABS plastic Bubble Polycarbonate Finish White or black Light Attenuation Smoked f/1.
C3425M-E (1/09) 33 CAMERA/LENS If you need technical specifications for the camera itself, refer to the IS90 specification online at www .pelco.com . (Design and product specifications subject to change without notice.) NOTE: V ALUES IN P ARENTHESES ARE CE NTIME TERS; ALL OTHERS ARE INCHES.
34 C3425M-E (1/09) REVISION HISTORY Manual # Date Comments C3425M 2/07 Or iginal version. C3425M-A 5/07 Updat ed switch sett ing and day/night operation descri ptions. C3425M-B 7/07 Changed part name of service connector from ICS-SC to IS-SC per CN20476.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment.
Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 U S A U S A & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .
デバイスPelco IS90の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco IS90をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco IS90の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco IS90の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco IS90で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco IS90を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco IS90の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco IS90に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco IS90デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。