PelcoメーカーIV SEの使用説明書/サービス説明書
ページ先へ移動 of 96
INSTALLATION/OPERATION C3412M (9/06) Spectra ® IV and Spectra ® IV SE Series Dome Drives.
.
C3412M (9/06) 3 Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installation . . . . . . . . . . . .
4 C3412M (9/06) Dome Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Camera . . . . . . . . . . . . . . . . . . . . . .
C3412M (9/06) 5 Aux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Edit Schedule . . . . . . . . . . . . . . . . . . .
6 C3412M (9/06) W elcome Thank you for purchasing Pelco’ s premier integrated dome system, Spectra ® IV/Spectra ® IV SE. Y our new system features a high resolution camera/optics package with programmable dome drive software. This manual is designed primarily to be a reference tool for the operation and programming of your system.
C3412M (9/06) 7 Installation NOTE: This manual contains installation instructions only for the Spectra IV/Spectra IV SE dome drive. For complete installation instructions for a Spectra IV/Spectra IV SE dome system, refer to the installation manual shipped with the back box.
8 C3412M (9/06) CM9502 Setting If a CM9502 matrix system is used with the dome drive, set SW2-2 to the ON position. Vicon System The Vicon protocol is not currently available.
C3412M (9/06) 9 DOME DRIVE INSTALLATION Install the dome drive. Line up the blue and red tabs with the blue and red arrows on the hinged door inside the back box. Push the tabs in. Insert one side and then the other side. Continue pushing on the ends of the tabs until both sides click into place.
10 C3412M (9/06) T able A. Switch Settings for SW1 P-T ype Control SPECTRA ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF.
C3412M (9/06) 11 T able B. Switch Settings for SW1 D-T ype Control SPECTRA ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF .
12 C3412M (9/06) 36 OFF OFF ON OFF OFF ON OFF OFF 37 ON OFF ON OFF OFF ON OFF OFF 38 OFF ON ON OFF OFF ON OFF OFF 39 ON ON ON OFF OFF ON OFF OFF 40 OFF OFF OFF ON OFF ON OFF OFF 41 ON OFF OFF ON OFF O.
C3412M (9/06) 13 71 ON ON ON OFF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF.
14 C3412M (9/06) 106 OFF ON OFF ON OFF ON ON OFF 107 ON ON OFF ON OFF ON ON OFF 108 OFF OFF ON ON OFF ON ON OFF 109 ON OFF ON ON OFF ON ON OFF 110 OFF ON ON ON OFF ON ON OFF 111 ON ON ON ON OFF ON ON .
C3412M (9/06) 15 141 ON OFF ON ON OFF OFF OFF ON 142 OFF ON ON ON OFF OFF OFF ON 143 ON ON ON ON OFF OFF OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 146 OFF ON OFF OFF ON.
16 C3412M (9/06) 176 OFF OFF OFF OFF ON ON OFF ON 177 ON OFF OFF OFF ON ON OFF ON 178 OFF ON OFF OFF ON ON OFF ON 179 ON ON OFF OFF ON ON OFF ON 180 OFF OFF ON OFF ON ON OFF ON 181 ON OFF ON OFF ON ON.
C3412M (9/06) 17 211 ON ON OFF OFF ON OFF ON ON 212 OFF OFF ON OFF ON OFF ON ON 213 ON OFF ON OFF ON OFF ON ON 214 OFF ON ON OFF ON OFF ON ON 215 ON ON ON OFF ON OFF ON ON 216 OFF OFF OFF ON ON OFF ON.
18 C3412M (9/06) 246 OFF ON ON OFF ON ON ON ON 247 ON ON ON OFF ON ON ON ON 248 OFF OFF OFF ON ON ON ON ON 249 ON OFF OFF ON ON ON ON ON 250 OFF ON OFF ON ON ON ON ON 251 ON ON OFF ON ON ON ON ON 252 OFF OFF ON ON ON ON ON ON 253 ON OFF ON ON ON ON ON ON 254 OFF ON ON ON ON ON ON ON T able B.
C3412M (9/06) 19 Getting Started Once installed, apply power to the Spectra IV/Spectra IV SE dome system. The system will start a configuration sequence. When configuration is done, the following information is displayed: Pelco Spectra IV/Spectra IV SE V ersion X.
20 C3412M (9/06) How to Operate Y our Dome System Operation How to Control Pan and T ilt Move joystick or press the direction keys left/right and up/down. Zoom Far T o zoom far , do the following: 1. Press the Zoom T ele button or turn the joystick clockwise until zoom stops at the 32X zoom limit.
C3412M (9/06) 21 QUICK PROGRAMMING GUIDE Access main menu (preset 95). See the Accessing Main Menu (Preset 95) section. Use the joystick to position the cursor beside menu selection. NOTE: If your controller does not have a joystick, use the up or down key .
22 C3412M (9/06) CM9500 1. Enter the number of the Spectra IV/Spectra IV SE dome system and press the CAM key . The main menu appears. 2. Highlight SETUP in the main menu and press the SELECT key . 3. Highlight CAM in the Setup menu and press the SELECT key .
C3412M (9/06) 23 NET300/NET350/NET4001A 1. Check the Set box. 2. Click the preset 95 button. The main menu appears. WS5050 1. Right-click in the video pane of the Spectra IV/Spectra IV SE dome system. 2. Click Preset and then click Select Preset. 3. Enter 95 and then click OK.
24 C3412M (9/06) 16X LowLight Color Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SPECTRA IV DOME DRIVE MODEL XX-XXXX SERIAL # XXXXXXXXXXXXXX BACK BOX MEMORY AV AILABLE SOFTWARE VERSION XX.
C3412M (9/06) 25 PRESET NUMBER 1 PRESETS PA TTERNS LINE SYNC ON LINE SYNC PHASE 0 LINE SYNC ENABLE TITLE TEXT <EDIT TITLE TEXT> TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXY .
26 C3412M (9/06) 22X EXview LowLight Black-White Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT .
C3412M (9/06) 27 LINE SYNC ON LINE SYNC PHASE 0 LINE SYNC RESUME OFF 5 0 SEQUENCE (SECS) RESET DELA Y (SECS) <ALARM SETTINGS> ALARM CONT ACT ALARMS ALARM SETTINGS ENABLE TITLE TEXT <EDIT TITLE TEXT> TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXY .
28 C3412M (9/06) 22X EXview LowLight Color Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM.
C3412M (9/06) 29 LINE SYNC ON LINE SYNC PHASE 0 LINE SYNC RESUME OFF 5 0 SEQUENCE (SECS) RESET DELA Y (SECS) <ALARM SETTINGS> ALARM CONT ACT ALARMS ENABLE TITLE TEXT <EDIT TITLE TEXT> TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXY .
30 C3412M (9/06) 23X LowLight Day/Night Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SP.
C3412M (9/06) 31 ALARM CONT ACT ALARMS ENABLE TITLE TEXT <EDIT TITLE TEXT> TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXY .,-/ abcdefghij klmnopqrst uvwxyz# &: * EDIT THE PASSWORD <CAM.
32 C3412M (9/06) 35X LowLight Day/Night Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SP.
C3412M (9/06) 33 DETECTION AREA 1 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 2 LOCA TION SENSITIITY 0 MEDIUM 0 MEDIUM 0 MEDIUM DETECTION AREA 3 LOCA TION SENSITIVITY DETECTION AREA 4 LOCA TION SENS.
34 C3412M (9/06) Language The language for the on-screen menus is selectable. Available languages include English, Spanish, French, German, Italian, Portuguese, Russian, Polish, T urkish, and Czechoslovakian. The factory default language is English. T o change the display language: 1.
C3412M (9/06) 35 System Information The System Information screen displays dome drive model, software version, available memory , and other diagnostic information. System settings cannot be changed using this screen. This screen is for reference only .
36 C3412M (9/06) Display Setup Display setup allows you to program how labels are displayed on the monitor . The following labels are available: PRESET LABEL Identifies preset. ZONE LABEL Identifies zone. ZOOM Identifies the amount of magnification.
C3412M (9/06) 37 LABEL POSITIONS Labels can be placed anywhere on the monitor . This feature allows you to customize the appearance of your monitor screen. The following labels are not set at fixed positions: PRESET LABEL ZONE LABEL ALARM 1 ZOOM RA TIO - XXX.
38 C3412M (9/06) Dome Settings CAMERA T YPE OF LIGHTING (Does not apply to 16X or 23X models.) Pelco has calibrated settings that optimize the white balance and the picture for indoor and outdoor lighting conditions.
C3412M (9/06) 39 ZOOM LIMIT Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The settings vary depending on camera model. 16X (Models DD4TC16 and DD4TC16-X) The default setting is 32X. Cameras with 128X zoom (16X optical zoom and 8X digital zoom) can be set for 16X, 32X, 64X, or 128X.
40 C3412M (9/06) ZOOM SPEED Zoom speed allows the user to define how fast the dome will go from full wide zoom to the 16X, 22X, 23X, or 35X optical zoom. Available zoom speed settings for 16X models include the following: HIGH 1.9 seconds MEDIUM (default) 3.
C3412M (9/06) 41 IR CUT FILTER (Applies only to 23X and 35X models.) The 23X and 35X cameras have two modes of operation: color , and black-white. Y ou can increase sensitivity in low light conditions by switching to black-white mode (removing the IR cut filter).
42 C3412M (9/06) ADVANCED CAMERA SETTINGS SHUTTER SPEED Shutter speed is the duration of the electronic shutter . Program shutter speed to operate automatically (Auto) or manually (Numeric V alue). AUTO (default) The electronic shutter speed is set automatically by the amount of light sensed by the camera.
C3412M (9/06) 43 AUTO IRIS Auto iris is the lens function that automatically opens and closes the iris in response to changing light conditions. Program the auto iris to operate automatically or at a user -defined level. OFF Auto iris is disabled, and control is always manual.
44 C3412M (9/06) AUTO SHARPNESS Auto sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture. There are two settings: ON (default) The camera automatically maintains a normal sharpness mode.
C3412M (9/06) 45 BACKLIGHT COMPENSATION (BLC) If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The dome uses the center of the picture to adjust the iris.
46 C3412M (9/06) VIDEO LEVEL Set the video output to one of the following: NORMAL 1.0 volt peak-to-peak HIGH (default setting) 1.2 volt peak-to-peak to compensate for losses in video cable.
C3412M (9/06) 47 ELECTRONIC IMAGE STABILIZATION (Applies only to 35X models.) Electronic image stabilization is a feature of the camera that can compensate for some forms of external influences. In all cases, care should be taken to make sure that any dome system is mounted to a rigid location.
48 C3412M (9/06) MOTION SETTINGS AUTO FLIP When the camera tilts downward and goes just beyond the vertical position, the dome rotates 180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you continue to hold the joystick in the down position.
C3412M (9/06) 49 PARK T IME This feature allows the dome to begin a specified operation (scan, preset, or pattern) after a programmed time of inactivity . Park time can be programmed from 1 minute to 720 minutes (12 hours), or set to zero, which disables this feature.
50 C3412M (9/06) SCAN SPEED Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed is adjustable from 1 to 40 degrees per second through the programming menu. The default setting is 25 degrees per second. PRESET FREEZE FRAME This feature freezes the scene on the monitor when going to a preset.
C3412M (9/06) 51 LIMIT STOPS Limit stops are programmable stops that limit the pan range of the dome. There must be two limits, a left and a right, to define an area. There are two types of limit stops: MANUAL A manual (joystick) pan operation stops when a limit stop is reached.
52 C3412M (9/06) AZIMUTH ZERO Azimuth is the pan angle from 0° to 359°. Azimuth zero is the pan position you specify to be the 0° point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point.
C3412M (9/06) 53 POWER UP POWER UP ACTION This setting defines a specific activity (scan, preset, pattern) to be performed in the event the power to the dome is cycled. The following settings are available: NONE No action. AUTO (default) The dome resumes its prior activity or direction before the power outage.
54 C3412M (9/06) LINE SYNC Line sync refers to a programmable function that allows you to synchronize all cameras within a matrix system. NOTE: Spectra IV and Spectra IV SE dome systems automatically sense V-Sync input. No line sync setup is required for Pelco control systems that provide a V-Sync signal.
C3412M (9/06) 55 PRESETS NOTE: The number of programmable presets available is limited by the model of the back box you are using. If you are using an older model back box, you may not have access to all of the available presets. Refer to the table below for a list of back boxes and the presets available for each.
56 C3412M (9/06) NOTE: For American Dynamics controllers with only 32 presets, switch SW2-1 on the dome drive to the ON position. When SW2-1 is ON, preset 99 becomes 32 92 becomes 25 98 becomes 31 91 .
C3412M (9/06) 57 4. Edit preset camera settings: a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS. b. Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor . Refer to the Camera and Advanced Camera Settings sections of this manual to change preset camera settings.
58 C3412M (9/06) ENABLE MOTION DETECTION (Applies only to 23X and 35X models.) The following are the settings for motion detection: OFF (default) Motion detection is turned off (disabled). ON Motion detection is turned on (enabled). NOTE: Motion detection does not work if the shutter speed is set at less than 1/60 of a second.
C3412M (9/06) 59 NOTE: Motion detection is not guaranteed to catch 100% of activity . EDIT DETECTION AREAS DETECTION AREA 1 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 2 LOCA TION 0 SENSITIVITY MEDI.
60 C3412M (9/06) ACTIVATE AUX COMMAND (Applies only to 23X and 35X models.) Motion detection can be programmed to trigger an auxiliary command when motion is detected. The following are the settings for ACTIV A TE AUX: OFF (default) Motion detection will not trigger an AUX command.
C3412M (9/06) 61 PATTERNS A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm, park, event, or power -up). Both 16X and 23X models have one user -defined pattern available.
62 C3412M (9/06) ZONES A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The Spectra 4 and Spectra IV SE dome systems are capable of eight zones, each with a 20-character label. T o program a zone: 1. Use the joystick to position the cursor beside ZONE NUMBER.
C3412M (9/06) 63 WINDOW BLANKING Window blanking allows a user to program four -sided areas that cannot be viewed by the operator of the dome system. A blanked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide.
64 C3412M (9/06) 6. The blanked area can be programmed to turn on or off at a specified zoom point. T o set the zoom point: a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press Iris Open. b. Zoom in to the point where you want window blanking to turn on.
C3412M (9/06) 65 BLANK ALL ABOVE/BLANK ALL BELOW The Blank All Above and Blank All Below options add additional flexibility to setting up privacy areas. These settings are ideal for applications where a complete pan location needs to be blanked. Blank All Above Blanks everything above a user -defined tilt angle.
66 C3412M (9/06) ALARMS The Spectra IV SE dome systems have seven alarm inputs that can be programmed as high, medium, or low priority . When an alarm is received, an input signal to the dome triggers the user - defined action (go to preset, run pattern, etc.
C3412M (9/06) 67 3. Select the alarm priority: a. Use the joystick to position the cursor beside ALARM PRIORITY . b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the available selections. Available settings include HIGH, MEDIUM, and LOW (default).
68 C3412M (9/06) 5. Set the auxiliary to activate: a. Use the joystick to position the cursor beside ACTIV A TE AUX. b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the following available selections. NO (default) Not activated.
C3412M (9/06) 69 AUX NOTE: The auxiliary feature is functional and available for 16X and 23X models only if the dome drive is installed in a Spectra III SE or Spectra IV SE back box. An auxiliary output is a programmable signal from the dome back box that can trigger another device to operate.
70 C3412M (9/06) T ITLE T EXT T itle text is the label used to identify the camera viewed on the monitor . Up to 20 characters can be used for a title. T o edit the title text label, do the following: 1. Use the joystick to position the cursor beside EDIT TITLE TEXT .
C3412M (9/06) 71 ALERT NOTE: The Alert option applies only to Pressurized Spectra IV dome systems. Spectra 4 systems that are not pressurized will not display this menu item. Sensors strategically placed inside the pressurized dome system continually monitor pressure, temperature, and dew point.
72 C3412M (9/06) ACK ACTION Acknowledge action programs the alert label behavior after the alert condition has been acknowledged. The following settings are available for acknowlegde: AL W A YS ON The alert label is displayed until alert conditions are cleared.
C3412M (9/06) 73 CLEAR Use this setting to clear user -defined settings or return the dome to factory default settings. The following are the available settings: ALL ZONES Clears all zones. T o clear a single zone, refer to the Zones section. ALL PRESETS Clears all presets.
74 C3412M (9/06) PASSWORD Spectra IV and Spectra IV SE feature password protection to prevent unauthorized changes to the dome settings. An operator can open the System Information and Display Setup screens, but cannot access any of the dome settings menus.
C3412M (9/06) 75 CLOCK The clock is used to program the current date and time. The date and time set in the Clock menu is used to program events. The date and time can also be displayed on the monitor when the menus are not being accessed. T o program the clock, do the following: 1.
76 C3412M (9/06) 7. If FIXED DA TE was selected, the following appears on the monitor: a. Use the joystick to position the cursor beside TIME SHIFT . Press Iris Open. Scroll through the options until the desired selection appears. Press Iris Open to select the time shift.
C3412M (9/06) 77 8. If RELA TIVE DA TE was selected, the following appears on the monitor: Follow the instructions in step 7 for FIXED DA TE, adding WEEK.
78 C3412M (9/06) EVENT An event is a preprogrammed camera, park, scan, preset, pattern, window blanking, alarm, or auxiliary function that can be performed automatically at a specific date and time. For example, suppose a camera is set to run in a continuous pattern that scans a parking lot during business hours Monday through Friday .
C3412M (9/06) 79 EDIT EVENT LABEL Use the following steps to edit the event label. 1. Use the joystick to position the cursor beside EDIT EVENT LABEL. 2. Press Iris Open. The following appears on the monitor: 3. Use the joystick to position the cursor beside a character .
80 C3412M (9/06) EDIT EVENT Use the following steps to edit an event. 1. Use the joystick to position the cursor beside EDIT EVENT . 2. Press Iris Open. The following appears on the monitor: a. Use the joystick to position the cursor beside EVENT ACTIVE.
C3412M (9/06) 81 CLEAR EVENT T o clear an event: 1. Use the joystick to position the cursor beside CLEAR EVENT . 2. Press Iris Open. 3. Follow the directions displayed on the monitor . LIST EVENT T o list events: 1. Use the joystick to position the cursor beside LIST EVENT .
82 C3412M (9/06) EDIT HOLIDAY Use the following steps to edit a holiday: 1. Use the joystick to position the cursor beside EDIT EVENT LABEL. 2. Press Iris Open. 3. Use the joystick to position the cursor beside OCCURRENCE. Press Iris Open. The following are the settings for Occurrence: FIXED DA TE Holiday occurs on the same date each year .
C3412M (9/06) 83 CLEAR HOLIDAY T o clear a holiday: 1. Use the joystick to position the cursor beside CLEAR HOLIDA Y . 2. Press Iris Open. 3. Follow the directions displayed on the monitor . LIST HOLIDAYS T o list events: 1. Use the joystick to position the cursor beside LIST HOLIDA YS.
84 C3412M (9/06) SCHEDULED EVENTS Use this page to record scheduled events. ________________________________________________________________________________________ ___________________________________.
C3412M (9/06) 85 Reset, Cycle Power , Reboot RESET CAMERA Use this function to reset all camera settings to factory default parameters. CYCLE CAMERA POWER If the camera is not operating or if you lose camera control, cycle camera power . Cycling camera power resets the camera but does not change any saved camera settings.
86 C3412M (9/06) Software/Language File Upload The RJ-45 data port of the dome drive allows access for on-site setup, testing, and uploading of revised operating software and language files. A Pelco field service tool is required to perform these operations.
C3412M (9/06) 87 Suggested Preventative Maintenance The Spectra IV and Spectra IV SE dome systems do not require any special maintenance. Occasionally , dust may build up on the inside or the outside of the dome. If this occurs, turn power to the unit off and remove the lower dome from the back box.
88 C3412M (9/06) Specifications 16X MODELS DD4TC16 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch interline transfer CCD Effective Pixels 768 (H) X 494 (V) Horizontal Resolution >470 TV lines Lens F1.4 (f=4~64 mm optical, 16X optical zoom, 8X digital zoom) Zoom Speed (optical range) 1.
C3412M (9/06) 89 22X MODELS (MONOCHROME) DD4M22 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 494 (V) Horizontal Resolution >500 TV lines Lens F1.6 (f=4~88 mm optical, 22X optical zoom, 12X digital zoom) Zoom Speed (optical range) 2.
90 C3412M (9/06) 22X MODELS (COLOR) DD4C22 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 494 (V) Horizontal Resolution >470 TV lines Lens F1.6 (f=4~88 mm optical, 22X optical zoom, 12X digital zoom) Zoom Speed (optical range) 2.
C3412M (9/06) 91 23X MODELS DD4CBW23 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 494 (V) Horizontal Resolution >470 TV lines Lens F1.6 (f=3.6~82.8 mm optical, 23X optical zoom, 12X digital zoom) Zoom Speed (optical range) 2.
92 C3412M (9/06) DD4CBW23-X Signal Format P AL Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 582 (V) Horizontal Resolution >470 TV lines Lens F1.6 (f=3.6~82.8 mm optical, 23X optical zoom, 12X digital zoom) Zoom Speed 2.
C3412M (9/06) 93 35X MODELS DD4CBW35 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 768 (H) X 494 (V) Horizontal Resolution >540 TV lines Lens F1.4 (f=3.4~119 mm optical, 35X optical zoom, 12X digital zoom) Zoom Speed (optical range) 3.
94 C3412M (9/06) DD4CBW35-X Signal Format P AL Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 582 (V) Horizontal Resolution >540 TV lines Lens F1.4 (f=3.4~119 mm optical, 35X optical zoom, 12X digital zoom) Zoom Speed 3.
PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherlands | United Arab Emirates | United Kingdom | United States W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
デバイスPelco IV SEの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco IV SEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco IV SEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco IV SEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco IV SEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco IV SEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco IV SEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco IV SEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco IV SEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。