PelcoメーカーMC3700 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 16
® Installa tion/Oper a tion MC3700 Series Monoc hr ome Camera C1987M (6/02) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.
[ 2 ] Pelco Manual C1987M (6/02).
Pelco Manual C1987M (6/02) [ 3 ] CONTENTS IMPORT ANT SAFEGUARDS AND W ARNINGS .............................................................................................. ....... 4 Regulatory Notices .................................................
[ 4 ] Pelco Manual C1987M (6/02) IMPORT ANT SAFEGU ARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should be done only by qualified service and installation personnel.
Pelco Manual C1987M (6/02) [ 5 ] DESCRIPTION The MC3700 Series monochrome video camera is compact, with a 1/3-inch CCD imager . The camera has a direct drive/auto iris lens connector and adjustable back focus, and accepts C and CS lenses. Models MC3700S-2 Standard resolution, 380 TV lines, SuperHAD™ CCD, 0.
[ 6 ] Pelco Manual C1987M (6/02) CAMERA LA Y OUT BACK FOCUS ADJUSTMENT RING BNC VIDEO CONNECTOR LENS CONNECTOR LED MOUNT ADAPTER PHASE ADJUSTMENT LENS LEVEL ADJUSTMENT POWER CONNECTOR BACK FOCUS ADJUS.
Pelco Manual C1987M (6/02) [ 7 ] PIN DC (AID) AUTO IRIS LENS VIDEO (AIV) AUTO IRIS LENS 1 Control coil negative (-) Not used 2 Control coil positive (+) Lens positive supply 3D rive coil positive (+) Video drive signal 4D rive coil negative (-) Ground Figure 2.
[ 8 ] Pelco Manual C1987M (6/02) POWER AND VIDEO CONNECTIONS MC3700 Series camera is designed to operate from a 12 VDC or 24 V AC power supply . The power supply con- nections are shown in Figure 4. The LED on the back panel of the camera indicates that power is connected.
Pelco Manual C1987M (6/02) [ 9 ] AC Operation Only – If you are wiring more than one camera to the same transformer , connect one side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the remaining terminal on all cameras.
[ 10 ] Pelco Manual C1987M (6/02) LENS SETUP AND FOCUS PROCEDURES V ideo Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak).
Pelco Manual C1987M (6/02) [ 11 ] BA CK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side).
[ 12 ] Pelco Manual C1987M (6/02) SWIT CH SETTINGS Figure 6. Switch Settings (Defaults) LL/INT Synchronization Selection – Switch Setting 10 Locks the frame rate to the power supply frequency . Eliminates vertical roll caused by multiple cameras connected to the same switching device.
Pelco Manual C1987M (6/02) [ 13 ] A GC OFF/A GC ON – Switch Setting 5 Automatically adjusts the image to compensate for low light levels when using fixed or manual iris lenses. AGC (Default setting) - Enables the AGC mode. OFF - Disables the AGC mode.
[ 14 ] Pelco Manual C1987M (6/02) CAMERA SYNCHRONIZA TION When using one AC power supply in a multi camera system, a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll adjust the phase control to synchronize (line-lock), the cameras to one another .
Pelco Manual C1987M (6/02) [ 15 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch Synchronization System: AC line lock or internal oscillator Horizontal Resolution: 380 TV lines Iris Control: Electronic/passive Minimum Illumination: 0.08 lux @ 50 IRE, f1.
[ 16 ] Pelco Manual C1987M (6/02) ® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco. ™ Esprit and Camclosure are trademarks of Pelco. ™ HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation. © Copyright 2002, Pelco.
デバイスPelco MC3700 Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco MC3700 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco MC3700 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco MC3700 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco MC3700 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco MC3700 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco MC3700 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco MC3700 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco MC3700 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。