PelcoメーカーPT7700の使用説明書/サービス説明書
ページ先へ移動 of 25
C997M 3500 Pelco W ay , Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100 • F AX (800) 289-9150 W ARNING! ® W arning! When lifting, transporting, or un- packing the PT7700 Series pan/tilt systems, DO NOT use the camera enclosure as a handle.
Pelco Manual C397M (4/98) 1 ® Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 International Custome.
2 Pelco Manual C397M (4/98) LIST OF ILLUSTRA TIONS Figur e Page 1 PT7700 Series Input Wiring Diagram ................................................ 8 2 PT7700 Series Connector ................................................................. 9 3 T ilt Limit Stop Adjustment .
Pelco Manual C397M (4/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed.
4 Pelco Manual C397M (4/98) 2.0 DESCRIPTION The PT7700 systems combine an environmental camera enclosure, pan/tilt as- sembly , and receiver/driver into a single unit that you can install indoors or out- doors. Y ou can install 2/3-inch (1.69 cm) and 1-inch (2.
Pelco Manual C397M (4/98) 5 3.0 INST ALLA TION 3.1 MOUNTING Attach the base of the pan/tilt system to a flat surface. If you use a wall or pedestal mount, follow the instructions that are provided with the mount. Make sure the mounting surface can support four (4) times the weight of the pan/tilt system.
6 Pelco Manual C397M (4/98) j. On the bottom of the enclosure, remove the vent grill and filters at the front of the enclosure. Replace the grill with one of the vent cover plates that was attached to the camera sled as loose equipment. k. On the bottom of the enclosure, attach the other vent cover plate over the grill at the rear of the enclosure.
Pelco Manual C397M (4/98) 7 3.3 WIRING 1. Route the six-foot power/video/control cable through the wall or pedestal mount if applicable. 2. Connect the end of the cable with the 16-pin connector to the mating connec- tor in the base of the pan/tilt unit.
8 Pelco Manual C397M (4/98) Figure 1. PT7700 Series Input Wiring Diagram.
Pelco Manual C397M (4/98) 9 PT7729RX PT7723RX-1 PT7729RX-1 PT7729RX-3 PT7729RX-1/SL Base Connector Pin Assignments PT7729WX PT7723WX-1 PT7729WX-1 PT7729WX-3 Base Connector Pin Assignments PT7729RX-1/PP PT7729RX-3/PP With Alarm Outputs Base Connector Pin Assignments Figure 2.
10 Pelco Manual C397M (4/98) 3.4 TESTING SYSTEM AND ADJUSTING LIMIT STOPS T o test the system and adjust the limit stops: 1. Loosen the two pan limit stops at the base of the pan/tilt. 2. T urn on power . 3. T est the system by moving the pan/tilt to the left, right, up and down.
Pelco Manual C397M (4/98) 11 4.0 OPERA TION Refer to the manual for your control equipment for operating the pan/tilt system. If your enclosure has a thermostatically controlled blower , the thermostat is set to turn the fan on between 77 ° and 93 ° F (25 ° and 34 ° C) and to turn the fan off be- tween 62 ° and 78 ° F (17 ° and 26 ° C).
12 Pelco Manual C397M (4/98) 5.0 TROUBLESHOOTING Fuses are located inside the left cover of the pan/tilt unit. Fuses F1 (mother board) and F2 (camera) are 2/10-ampere, slow-blow fuses. F3 (pan/tilt) is a 1-ampere, slow-blow fuse. T o order fuses F1 and F2, specify the part number FUS2/10SB.
Pelco Manual C397M (4/98) 13 6.0 MAINTENANCE Perform the following maintenance at six-month (or more often in harsh environ- ments) intervals to prolong the operational life and appearance of the equipment. Window and Filters 1. Clean the window with a mild nonabrasive detergent in water and a soft cloth to maintain picture clarity .
14 Pelco Manual C397M (4/98) Tilt Adjustments and Lubrication 10. Remove the plastic cover on the right side of the pan/tilt unit. 1 1. Refer to Figure 5. V erify that the worm (B) is fully seated in the worm gear (A). If it is not, turn the two nuts (C) to lift the worm.
Pelco Manual C397M (4/98) 15 7.0 EXPLODED ASSEMBL Y DIAGRAMS Figure 6. Exploded Assembly Diagram for Blower and Circuit Board SCREWS COME WITH BLANKING PLA TE 2 1 4 5 6 7 F G H 12 8 B A B E 9 A B C 10.
16 Pelco Manual C397M (4/98) T able A. Parts List (Figure 6) Item Qty Description Part Number 1 1 V ent Grill 57004005COMP 2 2 Foam Filter EH550010045 4 1 Circuit Board Insulator EH450010256 5 1 Circu.
Pelco Manual C397M (4/98) 17 Figure 7. Exploded Assembly Diagram for Heaters and Circuit Board T able B. Parts List (Figure 7) Item Qty Description Part Number 1 1 Bracket/Heater Sink 57004020COMP 2 2.
18 Pelco Manual C397M (4/98) Figure 8. Wiring Diagram for Enclosure Circuit Board.
Pelco Manual C397M (4/98) 19 Figure 9. Component Locations for Enclosure Circuit Board Figure 10. Layout of T races on Enclosure Circuit Board.
20 Pelco Manual C397M (4/98) 8.0 SPECIFICA TIONS SYSTEM Input Voltage: 120 or 230 VAC, 50/60 Hz Power Requirements: PT7729RX, PT7729WX 0.35 A (42 vA) PT7729RX-1, PT7723RX-1, PT7729RX-1/PP, PT7729RX-1/SL, PT7729WX-1, PT7723WX-1 1.7 A (204 vA) PT7729RX-3, PT7729RX-3/PP, PT7729WX-3 1.
Pelco Manual C397M (4/98) 21 PAN/TILT Construction Body: Aluminum plate Side Covers: Vacuum-formed ABS plastic, UV protected Pan: 0-355 ° movement in horizontal plane, except PT7729RX-1/SL, which has.
22 Pelco Manual C397M (4/98) Wiretron Receiver/Driver Fuses: One 1 A, 3 AG type Two 2/10 A, 3 AG type Control Method: 15 pulse train (pulse width modulated) Pulse Amplitude: 35 mA current loop Cable R.
Pelco Manual C397M (4/98) 23 Figure 1 1. Dimension Drawing MODEL “A” “B” PT7729RX 32.50 (82.55) 29.00 (73.66) PT7729RX-1 PT7729RX-1/SL PT7729RX-1/PP PT7729RX-3 PT7729RX-3/PP PT7729WX PT7729WX-1 PT7729WX-3 PT7723RX-1 26.
24 Pelco Manual C397M (4/98) 9.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1998, Pelco. All rights reserved.
デバイスPelco PT7700の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco PT7700をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco PT7700の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco PT7700の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco PT7700で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco PT7700を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco PT7700の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco PT7700に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco PT7700デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。