PelcoメーカーSD5TACの使用説明書/サービス説明書
ページ先へ移動 of 20
SD5T AC Series Spectra Lite™ Dome Systems Operation and Programming Manual C2422M (5/00) ® P elco • 3500 P elco Wa y • Clovis , CA 93612-5699 USA • www .
2 Pelco Manual C2422M (5/00) CONTENTS Section Page IMPORT ANT SAFEGU ARDS AND W ARNINGS ................................................................ 3 OPERA TION .....................................................................................
Pelco Manual C2422M (5/00) 3 IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and ser vicing should only be done by qualified service personnel and conform to all local codes.
4 Pelco Manual C2422M (5/00) OPERA TION POWER-UP DISPLA Y When the Spectra Lite™ dome is pow ered up, the selected protocol, re vision number , and other inf or mation is display ed on the monitor .
Pelco Manual C2422M (5/00) 5 OPERA TING NOTES P AN AND TIL T FUNCTIONS Controller T ype Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Va r iable speed 0.
6 Pelco Manual C2422M (5/00) PROGRAMMING Programming Guide - Spectra Lite 1. Access main menu (preset 95). 2. Make main menu selections . Joystic k: Move up or do wn to position cursor or to toggle between selections. Iris Open: Enter Iris Close: Cancel PRESETS The follo wing presets are reserved for special functions .
Pelco Manual C2422M (5/00) 7 ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on y our monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 f or P elco’ s controllers varies according to the type of controller you are using.
8 Pelco Manual C2422M (5/00) AUTO FLIP There are two auto flip modes: On - Auto flip mode is enab led. Off - A uto flip mode is disabled. To change the auto flip mode: 1. Program preset 95 (28). The main menu appears. 2. P osition the cursor (>) beside Other .
Pelco Manual C2422M (5/00) 9 AUTO IRIS The following are the settings for auto iris: Mode Level To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
10 Pelco Manual C2422M (5/00) Main Menu <Camera> <Line Sync> <Power Up> <Other> EXIT Camera Menu Backlight comp Off Reset camera <Gain/AGC> <Auto-iris> <Next>.
Pelco Manual C2422M (5/00) 11 GAIN The gain adjusts the signal lev el of the video output. Increasing the gain in low light conditions will increase the lev el of noise in the picture. To change the gain: 1. Program preset 95 (28). The main menu appears.
12 Pelco Manual C2422M (5/00) Main Menu <Camera> <Line Sync> <Power Up> <Other> EXIT Line Sync Menu Line sync On Line sync phase 0 Exit Scan Limit Stops Refer to the documentation for your control system for programming presets, and then do the following: 1.
Pelco Manual C2422M (5/00) 13 P ARK TIME MINUTES This feature causes the dome to park at preset 1 after a progr ammed number of minutes of control inactivity . The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature.
14 Pelco Manual C2422M (5/00) RESET CAMERA Main Menu <Camera> <Line Sync> <Power Up> <Other> EXIT Camera Menu Backlight comp Off Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Resetting the camera returns the settings to their defaults.
Pelco Manual C2422M (5/00) 15 SCAN SPEED Next Menu Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to prev .
16 Pelco Manual C2422M (5/00) SHUTTER SPEED Next Menu Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to prev .
Pelco Manual C2422M (5/00) 17 Next Menu Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to prev . menu) Exit Main Menu <Camera> <Line Sync> <.
18 Pelco Manual C2422M (5/00) MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch the surfaces of the dome. Exterior Surface - Clean the dome’ s exterior surface with a nonabrasiv e cleaning cloth and cleaning agent that is safe f or acrylic.
Pelco Manual C2422M (5/00) 19 SPECIFICA TIONS MECHANICAL Pan Movement: 360 ° continuous pan rotation Ve r tical Tilt: Unobstructed +2 ° to -92 ° Manual P an/Tilt Speeds* Pan: 0.
20 Pelco Manual C2422M (5/00) P elco, the P elco logo, Camclosure, Esprit, Gene x, Legacy , and Spectra are registered trademarks of Pelco . © Cop yright 2000, P elc o. Endura and ExSite are trademarks of P elco. All rights reser ved. U.S . Patent No .
デバイスPelco SD5TACの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco SD5TACをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco SD5TACの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco SD5TACの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco SD5TACで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco SD5TACを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco SD5TACの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco SD5TACに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco SD5TACデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。