PelcoメーカーTLR2024の使用説明書/サービス説明書
ページ先へ移動 of 48
TLR2024 Time-Lapse VCR Installation/ Operation Manual C650M (12/98) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800.
2 Pelco Manual C650M (12/98) CONTENTS Section Page 1.0 GENERAL .................................................................................................. 5 1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE ..................... 6 1.2 REGULA T ORY NOTICES .
Pelco Manual C650M (12/98) 3 8.3 ALARM RECORDING ..................................................................... 32 8.3.1 Alarm Recording Connection ............................................... 33 8.3.2 External Time Clock Adjustment ........
4 Pelco Manual C650M (12/98) REVISION HISTOR Y Manual # Date Comments C650M 12/98 Original version. LIST OF T ABLES T able Page A Call Out/T ape End ............................................................................. 22 B Recording T imes in Hours .
Pelco Manual C650M (12/98) 5 RISK OF ELECTRIC SHOCK DO NOT OPEN W ARNING WARNING: T O REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SER VICEABLE PAR TS INSIDE REFER SER VICING TO QUALIFIED SER VICE PERSONNEL.
6 Pelco Manual C650M (12/98) 1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE Observe the following WARNINGS before installing and using this product. Follow all warnings and instructions marked on the VCR. Instructions Read all the safety and operating instructions before operating the VCR.
Pelco Manual C650M (12/98) 7 Cleaning Unplug the VCR from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Clean with a soft cloth slightly moistened with mild detergent and water. Wipe dry . NEVER USE PETROLEUM-BASED SOLUTIONS.
8 Pelco Manual C650M (12/98) Care of V ideo Cassette T ape 1. A void violent vibration and shock. 2. Do not place near a strong magnetic field (near a motor , transformer , or magnet). 3. Never place or store in direct sunlight. 4. A void dusty places.
Pelco Manual C650M (12/98) 9 2.0 OVER VIEW 2.1 INTRODUCTION TO TIME-LAPSE RECORDERS T ime-lapse recording permits longer than ordinary recording times. The primary reason for using time-lapse recording in a CCTV security system is that a single VCR tape can be used for an extended period of time beyond the standard record- ing time.
10 Pelco Manual C650M (12/98) External Time Clock Adjustment– Y ou can reset the on-screen clock to the near- est hour by applying a signal to the RST (reset) IN terminal at the rear of the VCR. Record Check– Y ou can confirm correct recording by pressing the PLA Y button during recording.
Pelco Manual C650M (12/98) 11 3.0 QUICK ST AR T 3.1 BASIC ST AR T 1. Decide where to locate the VCR. Do all system hookups first (camera, multi- plexer , etc.) if you are installing the VCR in a location where you cannot ac- cess its rear panel. 2. Connect the VCR to other equipment (Sections 4.
12 Pelco Manual C650M (12/98) 4.0 INST ALLA TION 4.1 PRE-INST ALLA TION CAUTIONS 1. Provide secure power to system components. Prevent overloading or shorting by dedicating power circuits to the surveillance equipment. Restrict access to the surveillance system circuit breakers, switches, and equipment power cords.
Pelco Manual C650M (12/98) 13 Figure 1. T ypical System Setup AUDIO OUT MIC IN VIDEO OUTPUT FROM CAMERA VIDEO IN AUDIO IN MONITOR VIDEO OUT CCTV CAMERA VIDEO IN MIC 600 Ω VIDEO OUT IN IN OUT MIC AUD.
14 Pelco Manual C650M (12/98) 4.3 CONNECTING THE VCR TO A MUL TIPLEXER Figure 2 shows how to connect the VCR to an MX4000 Series Genex™ Multiplexer. • For Automatic Speed T racking (“B” lines in Figure 2) This lets the VCR control the multiplexer ’s recording speed.
Pelco Manual C650M (12/98) 15 5.0 CONTROLS 5.1 FRONT P ANEL 1. POWER button Press for on; press again for off. The POWER indicator illuminates when the VCR is turned on. 2. EJECT button Press to remove the cassette. 3. Cassette loading slot Insert the cassette in this slot to load it.
16 Pelco Manual C650M (12/98) 5.2 FLUORESCENT DISPLA Y 1. M (counter memory) indicator Illuminates during rewind for counter memory mode. 2. PL (power loss) indicator Illuminates when there is a power failure during recording. 3. ALARM indicator Flashes during alarm recording and stays on when the alarm recording is finished.
Pelco Manual C650M (12/98) 17 5.3 REAR P ANEL W ARNING: The included power cord is used for 120 V AC, 60 Hz. Never connect the power cord to any output or power supply having a different voltage or frequency . 1. AC power socket The power cord plugs into this socket.
18 Pelco Manual C650M (12/98) 6.0 PROGRAMMING 6.1 GENERAL PROGRAMMING INSTRUCTIONS The following is a universal procedure that shows how programming is done on the VCR. Use the JOG dial to select items, the SHUTTLE ring to the right to enter, and SHUTTLE ring to the left to exit.
Pelco Manual C650M (12/98) 19 6.2 QUICK GUIDE TO TLR2024 MENU STRUCTURE The operating parameters of the VCR are set through various on-screen menus. Program your choices on the menus according to the instructions on the following pages.
20 Pelco Manual C650M (12/98) 6.3 MAIN MENU • DISPLA Y Sets the time/date and direction to search for a desired location on a tape. • TIMER PROGRAM Sets the timed recordings. • RECORDING SET UP Sets the alarm recording mode, alarm recording duration, and emergency recording.
Pelco Manual C650M (12/98) 21 6.5 TIMER PROGRAM MENU (program number) This number identifies the program. If the recording times of two programs overlap, the higher program number has priority. DW Day of the week. DAY is used to record at the same time every day.
22 Pelco Manual C650M (12/98) 6.7 REAR TERMINAL MENU CALL OUT Sets the call signal output at the end of the tape. Turns on or off the signal that comes from the CALL terminal when the end of the tape is reached during recording.
Pelco Manual C650M (12/98) 23 MODE OUT Sets the state in which the signal output at the MODE OUT terminal is switched to active. When you turn the JOG dial, the display switches in the following order.
24 Pelco Manual C650M (12/98) • REPEA T – Rewinds the tape to the beginning and re- sumes recording. • ALARM•PROT – (Alarm Protection) If alarm recordings are on the tape, then the tape stops. “End” appears on the fluorescent display and “T ape End” on the monitor.
Pelco Manual C650M (12/98) 25 6.9.2 Set the Day and Time 1. Press the DISPLA Y button to display the Main menu on the monitor . 2. T urn the JOG dial to select FIRST TIME SET UP . 3. T urn the SHUTTLE ring to the right. The First T ime Set Up menu will appear.
26 Pelco Manual C650M (12/98) 7. T o set the month, turn the SHUTTLE ring to the right. The month display will flash. T urn the JOG dial to the right to set the MONTH. 8. T o set the date, turn the SHUTTLE ring to the right. The date display will flash.
Pelco Manual C650M (12/98) 27 7.0 LOADING/UNLOADING/PROTECTING THE T APE CASSETTE Y ou can load video cassette tapes into your VCR as long as it is plugged into a power source. Loading a cassette automatically turns the VCR on even if its power switch is turned off.
28 Pelco Manual C650M (12/98) 8.0 RECORDING 8.1 MANUAL RECORDING 1. Load a cassette with the erasure prevention tab intact. 2. Press the REC/PLA Y MODE buttons (+/-) to select the desired recording mode. 3. Use the VIDEO switch to pick either color or black and white (B/W) recording.
Pelco Manual C650M (12/98) 29 8.1.2 Record Check Function When the VCR is recording, press the PLA Y button for more than 1.5 seconds and then release. The tape rewinds a little and then plays back the recording just made. When the tape reaches the spot where you pressed the PLA Y button, the VCR returns to record mode.
30 Pelco Manual C650M (12/98) 8.1.4.2 Recommended Number of T ape Uses V ideo tape wears during use. Use a new cassette according to the following table. T able D. Recommended Number Of T ape Uses Recording Number Of Repeat T ape Uses Time Mode T-120 Cassette T -160 Cassette 2H 100 50 6H 100 50 L12H 60 30 L24H 35 17 8.
Pelco Manual C650M (12/98) 31 8.2 TIMER RECORDING 8.2.1 Programming Pr ocedur e 1. Press the DISPLA Y button to display the Main menu on the monitor . 2. T urn the JOG dial to select TIMER PROGRAM and turn the SHUTTLE ring to the right. The TIMER PROGRAM display will appear .
32 Pelco Manual C650M (12/98) 8.2.3 Avoid Mistakes When Using the Timer Refer to T able E if you get an error when pressing the TIMER REC button. T able E. Timer Recording Troubleshooting SYMPT OM F AUL T ACTION TIMER REC indicator flashes • A tape is not inserted.
Pelco Manual C650M (12/98) 33 8.3.1 Alarm Recording Connection Y ou can confirm an alarm from a distance by connecting the ALM (alarm) OUT terminal to an existing alarm system panel or other external device such as a buzzer.
34 Pelco Manual C650M (12/98) 8.3.3 Programming for Alarm Recording Alarm recording speeds up recording when the VCR is recording in one of the time- lapse modes. Alarm recording provides more pictures during the alarm. Emergency recording activates alarm recording even if the VCR is off, stopped, or in timer recording/standby .
Pelco Manual C650M (12/98) 35 8.3.4 Emer gency Recor ding Emergency alarm recording can start when an alarm is triggered even if the VCR is stopped or is programmed for timer recording. 1. T urn the JOG dial to select EMERGENCY REC and turn the SHUTTLE ring to the right.
36 Pelco Manual C650M (12/98) 9.0 PLA YBACK 9.1 PLA YBACK PROCEDURE Figure 21. Playback Controls REW FF JOG/ADJUST CLEAR/ ENTER/ SHUTTLE REC STOP PLAY POWER EJECT PICTURE TRACKING POSITION/ VERTICAL ADJUST REC/PLAY MODE COUNTER RESET COUNTER MEMORY/ SKIP/INDEX PAUAE SHUTTLE HOLD DISPLAY TIMER REC VIDEO SOFT SHARP COLOR B/W 1.
Pelco Manual C650M (12/98) 37 T able F . Audio Playback Availability Playback mode 2H 6H L12H 12H L24H 24H Audio playback A vailable Available A vailable Not A vailable Available Available Picture quality Good Good V ibrating Less Vibrating Vibrating Less Vibrating 9.
38 Pelco Manual C650M (12/98) 9.2.1 Shuttle Ring Y ou can adjust the playback speed using the SHUTTLE ring. 1. Press the PLA Y button to begin playback. 2. Press the P AUSE/SHUTTLE HOLD button to get a still picture. 3. Turn the SHUTTLE ring to the appropriate angle for the playback speed you want.
Pelco Manual C650M (12/98) 39 9.2.3 Still Picture Y ou can get a still picture by pressing the P AUSE/SHUTTLE HOLD button during playback. Press it again to resume playback. 9.2.4 Frame-by-Frame Playback Y ou can use the JOG dial to advance the tape frame by frame.
40 Pelco Manual C650M (12/98) 9.3.2 Skip Search The VCR will fast forward or rewind until it finds an index signal. It then plays back for about four seconds in 2H or 6H mode. It repeats this process until reaching the end or beginning of the tape. 1.
Pelco Manual C650M (12/98) 41 9.4.2 Picture Quality Adjustment This control lets you adjust the playback picture so the outline is sharper or softer. 9.4.3 V er tical Adjustment The picture may vibrate when watching still, slow motion, fast playback, or normal playback in L12 or L24H mode.
42 Pelco Manual C650M (12/98) 10.0 ADDITIONAL FUNCTIONS AND FEA TURES 10.1 COUNTER 10.1.1 Counter Memory Press the COUNTER MEMORY/SKIP/INDEX button repeatedly until the “M” indi- cator appears on the fluorescent display . T urn the SHUTTLE ring to the right and the tape will rewind to the 00000 position of the counter and stop.
Pelco Manual C650M (12/98) 43 10.4 ELAPSED TIME DISPLA Y The elapsed time of recording and playback is stored in memory . Use the elapsed time as a guide for periodic replacement of parts. 1. Press the DISPLAY button to display the Main menu. 2. T urn the JOG dial to select MAINTENANCE and turn the SHUTTLE ring to the right.
44 Pelco Manual C650M (12/98) 12.0 TROUBLESHOOTING 12.1 SELF-DIAGNOSTIC FUNCTION AND W ARNING DISPLA Y The VCR uses self-diagnostics to detect internal malfunctions during recording. If one occurs, the VCR indicates it on the monitor and in the VCR’ s fluorescent dis- play .
Pelco Manual C650M (12/98) 45 12.2 BEFORE CALLING FOR SER VICE SYMPTOM REMEDY VCR does not operate. • Is the LOCK indicator illuminated? • Is the power cord disconnected from the AC output? • Is the TIMER REC indicator illuminated. The VCR power is on but unit does • Is the LOCK indicator illuminated? not operate.
46 Pelco Manual C650M (12/98) 13.0 SPECIFICA TIONS ELECTRICAL Power Source: 100-230 VAC, 50/60Hz. (The included power cord is used for 120 VAC, 60 Hz) Power Consumption: Approximately 20 watts Rating: ALM/CALL/ MODE Active: “Low” level, maximum current 50 mA (+5 VDC)/10 mA (+24 VDC) Non-active: Open, maximum voltage +24 VDC.
Pelco Manual C650M (12/98) 47 Display Format DISPLAY MODE 1: (Month)-(Day)-(Year) (Hour) : (Minute) : (Second) (Alarm re- cording no.) DISPLAY MODE 2: (Month)-(Day)-(Year) (Day of week) (Alarm recording no.
48 Pelco Manual C650M (12/98) Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco.
デバイスPelco TLR2024の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco TLR2024をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco TLR2024の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco TLR2024の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco TLR2024で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco TLR2024を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco TLR2024の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco TLR2024に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco TLR2024デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。