PelcoメーカーWLV2500の使用説明書/サービス説明書
ページ先へ移動 of 20
® P elco • 3500 Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981 FAX (800) 289-9150 or (1-559) 292-3827 WL V2500 Series Wir eless Control Link and V ideo T ransmission Syst.
ii Pelco Manual C914M (7/96) ®Pelco and the Pelco logo are registered trademarks of Pelco. ©Copyright 1996, Pelco. All rights reserved. T ABLE OF CONTENTS Section Page 1.0 W ARNINGS ...................................................................
LIST OF ILLUSTRA TIONS Figur e Page 1T ypical WL V500 Control Link and WL V2000 Video Link Configuration ............................................ 2 2T ransmitter-Receiver Placement at Same Site .....................................................
(This page intentionally left blank.) iv Pelco Manual C914M (7/96).
Pelco Manual C914M (7/96) 1 This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
2 Pelco Manual C914M (7/96) 2.0 SCOPE This manual covers the installation of the WL V2500 Series of outdoor wireless systems. 3.0 DESCRIPTION To make a WL V2500 system, a WL V500 control sys- tem is combined with a WL V200 video transmission system (refer to Figure 1).
Pelco Manual C914M (7/96) 3 Figure 2. T ransmitter-Receiver Placement at Same Site 4.0 ANTENNA LOCA TION To provide the best reception, proper placement of the transmit and receive antennas is important. Reception will be best when: • The antennas are a minimum of 8-10 feet above the floor (indoors) or ground (outdoors).
4 Pelco Manual C914M (7/96) 5.0 INST ALLA TION NOTE: Proper placement of the transmit and receive antennas is important for best reception. Read Section 4.0, “Antenna Lo- cation,” before installing the equipment. Install the WL V500 receiver and WL V2000 transmit- ter at the remote site where your camera will be.
Pelco Manual C914M (7/96) 5 5.2 WIRING NOTE: In the following steps w hen you as- semble coaxial cable, install a BNC connector on only one end. Run the bare end of the cable through the cable entry gland on the enclosure so that the end with the BNC connector is inside the enclosure.
6 Pelco Manual C914M (7/96) 5.4 ANTENNA ALIGNMENT NOTE: This section applies only to the WL V2000 wireless receiver . 1. Connect a high impedance voltmeter to the RSSI (Received Signal Strength Indication) test points on the bottom of the enclosure: a.
Pelco Manual C914M (7/96) 7 4. Check the power supply voltages for the wireless transmitter and receiver . If the voltage at the trans- mitter or receiver is less than 1 1 VDC, replace the unit’ s power supply . 5.5.2 Poor Picture 1. Refer to Section 4.
8 Pelco Manual C914M (7/96) 6.0 EXPLODED ASSEMBL Y DIAGRAM (OUTDOOR MODELS ONL Y) Figure 6. Outdoor Enclosure Exploded Assembly Diagram.
Pelco Manual C914M (7/96) 9 6.1 MECHANICAL P ARTS LIST Item Quantity Description Part Number 11 9-Pin Connector CON03-06-1091 22 Gland EH400010003 32 Gland Nut EH400010004 41 Gland CX950010000 51 Gland Nut CX950010001 62 Fuse Holder FUS342012L 71 Power Supply Assembly PCB9000281ASSY 81 3-Position T erminal Block TRB3-140Y 91 Tr ansformer T RF21162.
10 Pelco Manual C914M (7/96) 7.0 INTERCEPT ® DOME MODIFICA TION To use the WL V500 wireless control system with In- tercept ® dome drives DD08CXX, DD08EXX, DD14CXX, or DD14EXX (domes with 360 degree.
Pelco Manual C914M (7/96) 11 Figure 8. V ideo Board Component Locations Figure 9. Block Diagram.
12 Pelco Manual C914M (7/96) Figure 10. Coaxitron ® Receiver Backplane PCB - Wire Lead Additions and Wiring Diagram.
Pelco Manual C914M (7/96) 13 8.0 WIRING DIAGRAM NOTE: Output voltage is 15 VDC, not 10.5 Figure 1 1. Outdoor Enclosure Wiring Diagram 9.0 MAINTENANCE In cold, wet areas periodically visit the transmitter and receiver sites to prevent the buildup of snow and ice on the enclosures.
14 Pelco Manual C914M (7/96) Impedance: 75 ohms Connectors: BNC RF (WL V500) T ransmitter Radiated Power: FCC Part 15 (15.249) T ransmit Antenna: Attached, circular -polarized, patch antenna Receive A.
Pelco Manual C914M (7/96) 15 11.0 W ARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1996, Pelco. All rights reserved.
Pelco 3500 Pelco Way, Clovis, CA 93612-5699 (559) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (559) 292-3827 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.
デバイスPelco WLV2500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco WLV2500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco WLV2500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco WLV2500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco WLV2500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco WLV2500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco WLV2500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco WLV2500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco WLV2500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。