Pfaffメーカー100 sの使用説明書/サービス説明書
ページ先へ移動 of 40
100 s OWNER´S MANUAL.
This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594 IMPOR T ANT SAFETY INSTR UCTIONS When using an electrical appliance, basic safety precautions should alw ays be follo wed, including the f ollowing: Read all instructions before using this household sewing machine .
Congratulations As the owner of a new sewing machine, you are about to begin an exciting adventure in creativity . From the moment you fi rst use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made.
.
List of contents Principal parts of the machine ............................................................................ 2/3 Accessories ........................................................................................................ 4 Extension table .
2 Principal parts of the machine 1. T ension dial 2. Bobbin thread guide 3. Thread take-up 4. Reverse lever 5. Thread cutting 6. Presser foot 7. Needle plate 8. Accessory tray 9. Bobbin winder 10. Stitch width dial 1 1. Stitch length dial 12. Stitch selection dial 13.
3 Principal parts of the machine 14. Spool pin 15. Bobbin winder stop 16. Hole for second spool pin 17. Handwheel 18. Main switch 19. Main plug socket 20.
4 Accessories a. Standard foot b. Zipper foot c. Buttonhole foot d. Quilting foot e. Second spool pin f. Seam ripper/ brush g. Seam guide h. Needles i. Spool caps j. Bobbins k. Off-set screwdriver l. Feed dog cover m. Free-motion/darning foot n. Hard cover o.
5 Extension table Before sewing, please follow the arrow (1) of the drawing, and pull down the extension table. Extension table can help your fabric fl ow easier during sewing. When the sewing machine is not being used, store the machine with the extension table folded up.
6 Accessory tray Keep the snap-in accessory tray horizontal, and push it in the direction of the arrow . (1) Remove the accessory tray to sew cylindrical pieces such as sleeve cuffs. The inside of the snap-in accessory tray can be utilized to store your accessories.
7 1 2 Connecting machine to power source Connect the machine to a power source as illustrated. (1) The appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. Attention: Unplug power cord when machine is not in use.
8 Changing the light bulb Disconnect the machine from the power supply by removing the plug from the main socket! Replace bulb with same type rated 10 watts (1 10-120V) or 15 watts (220-240V). - Loosen screw (A) as illustrated. (1) - Remove the cover (B).
9 Presser foot lifter The presser foot lifter raises and lowers your presser foot. (A) When sewing several layers or thick fabrics, the presser foot can be raised higher for easy positioning of the work. (B) Adjusting presser foot pressure Standard presser foot pressure is set at "2".
10 Attaching the presser foot holder/presser foot/seam guide Raise the presser bar (a). (1) Attach the presser foot holder (b) as illustrated. Attaching the presser foot Lower the presser foot holder (b) until the cut-out (c) is directly above the pin (d).
11 Winding the bobbin - Place thread and spool cap onto spool pin (1). For smaller spools of thread place spool cap with small side next to spool (2). - Snap thread into thread guide (3). - Wind thread clockwise around bobbin winder tension discs (4).
12 Inserting the bobbin When inserting or removing the bobbin, the needle must be in the highest position. 1. Insert the bobbin in the bobbin case with the thread running counterclockwise direction (arrow). 2. Pull the thread through the slit (A). 3. Draw the thread clockwise until it slips into the notch (B).
13 Inserting and changing needle Change the needle regularly , especially if it is showing signs of wear and causing problems. Insert the needle following the illustrated instructions. A. Loosen the needle clamp screw and tighten again after inserting the new needle.
14 Threading the upper thread This is a simple operation but it is important to carry out correctly . - Start by raising the needle to its highest point (1), and also raise the presser foot to open the tension discs. (2) Note: For safety , it is strongly suggested you turn off the power before threading.
15 Thread tension Upper thread tension Basic thread tension setting: "4" T o increase the tension, turn the dial to the next number up. T o reduce the tension, turn the dial to the next number down. A. Normal thread tension for straight stitch sewing.
16 Raising the bobbin thread Hold the upper thread with the left hand. T urn the handwheel (1) towards you (counterclockwise) lowering, then raising needle. Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole (2).
17 Reverse sewing Reverse sewing is used for locking the end of seams and where reinforcement is needed. At the end of seam, press down the reverse sewing lever and touch the foot control lightly . Sew a few reverse stitches. Release lever and the machine will sew forwards again (A/1).
18 Matching needle/ fabric/ thread NEEDLE, F ABRIC, THREAD SELECTION GUIDE NEEDLE SIZE F ABRICS THREAD 9-1 1 (70-80) Lightweight fabrics: thin cottons, voile, serge, silk , muslin, Qiana, interlocks, cotton knits, tricot, jerseys, crepes, woven polyester , shirt & blouse fabrics.
19 How to choose your stitch T o select a stitch, simply turn the stitch selection dial. The stitch selection dial may be turned in either direction. The following page shows the recommended range of stitch lengths and widths. Adjust the stitch length with the stitch length dial.
20 Straight stitching T urn the stitch selection dial so that the stitch display shows the straight stitch position. Generally speaking, the thicker the fabric, thread and needle, the longer the stitch should be.
21 Zigzag stitching T urn the stitch selector dial to "A". Function of stitch width dial The maximum zigzag stitch width for zigzag stitching is "6"; however , the width can be reduced on any pattern. The width increases as you move zigzag dial from "0" - "6".
22 Overcasting stitches Seams, overcasting, visible hems. T urn stitch width dial to "6". Stretch overlock: (1) T urn stitch length dial to "S1". The stitch width can be adjusted to suit the fabric. For fi ne knits, jerseys, neck edges, ribbing.
23 Buttonholes Prepare 1. T ake off the standard foot and attach the buttonhole foot. 2. Measure diameter and thickness of button and add 0.3 cm (1/8”) for bar tacks; mark buttonhole size on fabric. 3. Place fabric under the foot, so that marking of the buttonhole foot aligns with marking of fabric.
24 Zippers and piping Set the pattern selector dial to " ". T urn stitch width dial to "0". Set stitch length control between "1" - "4". Change to zipper foot (1). The zipper foot can be attached right (2) or left (3) depending on which side of the foot you are going to sew .
25 3-step zigzag stitch Sewing on lace and elastic, darning, mending, reinforcing edges. Set the machine as illustrated. Set stitch width control between "4" - "6". Set stitch length control between "1" - "2". Place the patch in position.
26 Straight stretch stitch and Stretch triple zigzag stitch Straight stretch stitch Set the stitch pattern dial to "A". Used to add triple reinforcement to stretch and hardwearing seams. Set the stitch length dial to "S1". Set the stitch width dial to "0".
27 Free-motion darning Install the feed dog cover . (1) Set the stitch length dial to "0". Set the stitch width dial to "0". Remove the presser foot clamp. (2) Attach the free-motion/darning foot to the presser foot holder . The lever (A) should be behind the needle clamp screw (B).
28 Darning - Set the machine as illustrated. - T urn stitch width dial to "0". - T urn stitch length dial to the desired length. - Position the fabric to be darned under the presser foot together with the under laying fabric to be used. - Lower the presser foot and alternately sew forward or reverse using the lever .
29 Free-motion monogramming and embroidering - Set the machine as illustrated. - T urn stitch width dial to "0". - Remove the presser foot and the presser foot holder . - Attach the feed dog cover . (1) - Lower presser foot lever before starting to sew .
30 Quilting Set stitch selector as illustrated. T urn stitch width dial to "0". T urn stitch length dial to the desired length. Insert the quilting guide in presser foot holder and set the space as you desired. Use the quilting foot. Move the fabric over and sew successive rows with the guide riding along on the previous row of stitching.
31 T win needle (Optional) - T urn stitch width dial to "0". - T urn stitch length dial to the desired stitch length. - T urn stitch selector to straight stitch, center needle position. - For twin needle sewing, insert the extra spool pin (included with the accessories) into the hole on top of the machine.
32 Maintenance Attention: Disconnect the machine from the wall outlet before carrying out any maintenance or changing the sewing light bulb. Cleaning If lint and bits of thread accumulate in the hook, this will interfere with the smooth operation of the machine.
33 T roubleshooting guide Problem Cause Correction Upper thread breaks 1.The machine is not threaded correctly . 2.The thread tension is too tight. 3.The thread is too thick for the needle. 4.The needle is not inserted correctly . 5.The thread is wound around the spool holder pin.
.
Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/electronic products.
VSM Group AB • SE-561 84 Huskvarna • SWEDEN www .pfaff.com 412 97 76-26B • English • Inhouse production • © 2005 VSM Group AB • All statements valid at time of printing • Printed in Chi.
デバイスPfaff 100 sの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pfaff 100 sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPfaff 100 sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pfaff 100 sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pfaff 100 sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pfaff 100 sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPfaff 100 sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pfaff 100 sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPfaff 100 sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。