Pfaffメーカー1122-Gの使用説明書/サービス説明書
ページ先へ移動 of 46
INSTRUCTION MANUAL 296-1 2-1 8 581/0 02 Betriebsanleit ung engl . 06.09 This instr uction manual applies to mac hines from the follo wing serial numbers onw ards: # 6 0 0 1 0 0 0 Industrial ® 1 1 22 .
The reprinting, copying or translation of PF AFF Instruction Manuals, whether in whole or in part, is only permit ted with our pre vious authorization and with writ ten ref erence to the source. PF AFF Industriesysteme und Masc hinen AG Hans-Geiger -Str .
Contents Contents ................................................................................. Chapter - Page 1 Safety ........................................................................................................................... 1 - 1 1 .
Contents Contents ................................................................................. Chapter - Page 8. 01.06 Mounting the bottom V-belt guard ................................................................................ 8 - 4 8. 01.07 Mounting the top V-belt guard .
Safety 1 - 1 1 Safety 1 .01 Directives This machine is constructed in accordance with the European regulations contained in the conformity and manufacturer’s declarations.
S afety 1 - 2 1 .03 Safety symbols Danger! Points to be observed. Danger of injury for operating and specialist personnel! Caution Do not operate without finger guard and safety devices. Before threading, changing bobbin and needle, cleaning etc. switch off main switch .
Safety 1 - 3 1 .05 Operating and specialist personnel 1 .05.01 Operating personnel Operating personnel are persons responsible for the equipping, operating and cleaning of the machine as well as for taking care of problems arising in the sewing area.
S afety 1 - 4 Do not operate the machine without its take-up lever guard 1 ! Danger of injury due to the motion of the take-up lever! Do not operate the machine without the finger guard 2 ! Danger of .
P roper use 2 - 1 2 Proper use The PFAFF 1122 is a two-needle, lockstich sewing machine with needle feed and vertical hook. The PFAFF 1122-G is a two-needle, lockstich sewing machine with needle feed and large vertical hook. The PFAFF 1122-720/.. is a two-needle, lockstich sewing machine with needle feed, vertical hook, and disengagable needles.
Specifications 3 - 1 3 Specifications 3 .01 General specifications ▲ Stitch type: .................................................................................................. 310 (lockstitch) Needle system: ....................................
Specifications 3 - 2 3 .02 Versions and subclasses Versions Version A: ..................................................................................... for sewing fine materials Version B: .........................................................
Disposal of mac hine 4 - 1 4 Disposal of machine ● The proper disposal of the machine is the responsibility of the customer. ● The materials used in the machines are steel, aluminium, brass and various plastics. The electrical equipment consists of plastics and copper.
5 - 1 T ranspor t, pac kaging and storage 5 Transport, packaging and storage 5 .01 Transport to the customer’s premises The machines are delivered completely packed. 5 .02 Transport within the customer’s premises The manufacturer bears no liability for transport within the customer’s premises or to the in- dividual locations of use.
Explanation of the symbols 6 - 1 6 Explanation of the symbols In the following section of this Instruction Manual, certain tasks or important pieces of information are accentuated by symbols.
Controls 7 - 1 Fig. 7 - 01 7 Controls 7 .01 On/off switch ● Switch the machine on or off by turning main switch 1 . The switch in the illustration can be found on machines with Quick motors. When other motors are used, the switch may not look the same.
Controls 7 - 2 109-070 109-00 5 Fig. 7 - 03 7 .03 Lever for lifting the presser foot ● The presser foot is raised by turning lever 1 . 1 7 .04 Knee lever ● By pressing the knee lever 1 in the direction of the arrow, the presser foot is raised. Fig.
Controls 7 - 3 Fig. 7 - 05 7 .05 Key on the machine head (only on machines with backtacking device -911/93) ● If key 1 is pressed during the sewing operation, the machine switches to reverse sewing. 7 .06 Reverse feed key ● If key 1 is pressed during the sewing operation, the machine switches to reverse sewing.
Controls 7 - 4 7 .07 Stitch length adjustment wheel ● Set the required stitch length by turning adjustment wheel 1 . Fig. 7 - 07 1 7 .08 Switching needles (only on machines with disengagable needles -720/02) ● When lever 1 is adjusted, the desired needle bar is disengaged.
Controls 7 - 5 109-062 7 .09 Switch for the thread wiper (only on machines with thread wiper -909/93) ● The thread wiping function is switched on or off by pressing switch 1 .
Controls 7 - 6 7 .10 Control panel (only on machines with Quick-motor) The control panel consists of display 1 and the function keys described below. The display 1 consists of a single-line alpha-numerical, 7 segment LCD display with 8 symbols.
Controls 7 - 7 Start backtacks ● If this key is pressed, the backtacks at the beginning of the seam (start backtacks) are switched on or off. The number of forward stitches (A) or reverse stitches (B) for the start backtacks can be changed by pressing the +/- key underneath.
8 - 1 Installation and commissioning 109 - 010 Fig. 8 - 01 1 1 2 8 Installation and commissioning The machine must only be installed and commissioned by qualified personnel! All relevant safety regula.
8 - 2 Installation and commissioning 8 .01.02 Assembling the oil pan Fig. 8 - 02 ● Insert rubber support 1 . ● Insert bearing bushes 2 and fasten with nails. ● Place oil pan 3 in the table-top opening. ● Insert rubber pad 4 and fasten with nails.
8 - 3 Installation and commissioning 109-020 8 .01.04 Assembling the motor (only on machines with Quick-motor) Fig. 8 - 04 ● Assemble motor mounting 1 , motor 2 , belt guard support 3 and belt pulley 4 as shown in Fig. 8-04. 8 .01.05 Tightening the V-belt ● Fit the V-belt.
8 - 4 Installation and commissioning 109-071 8 .01.06 Mounting the bottom V-belt guard 1 Fig. 8 - 06 2 ● Loosen screws 2 and adjust belt guard support 1 so that the motor pulley and V-belt run freely. ● Tighten screws 2 . ● Fasten belt guard 3 with screw 4 .
8 - 5 Installation and commissioning 8 .01.08 Fitting the reel stand ● Fit the reel stand as shown in Fig. 8 - 08 . ● Afterwards insert the stand in the hole in the table top and secure it with nuts pro- vided. Fig. 8 - 08 8 .01.07 Mounting the top V-belt guard Fig.
8 - 6 Installation and commissioning 8 .01.09 Connecting the plug-in connections and earth cables Fig. 8 - 09 ● Connect the plug connections leading off the machine to adapter X5. ● Connect all plugs as labelled to the control box 1 . ● Screw the earth cable from the sewing head and the main switch to earth point A .
8 - 7 Installation and commissioning 8 .02 Commissioning Before commissioning the machine, clean it thoroughly, fill the oil pan with oil and adjust the oil level, see Chapter 10 Care and Maintenance! ● Examine the machine, in particular the electric cables, for any damage.
8 - 8 Installation and commissioning 8 .02.02 Basic position of the machine drive unit (only on machines with Quick motor) ● Switch on the machine. ● Press the TE/speed key twice to select the input mode. 2 x ● Select parameter "798" by pressing the corresponding +/- key , and select service level C , see Chapter 12.
8 - 9 Installation and commissioning 8 .03 Table top cutout..
8 - 10 Installation and commissioning 8 .04 Mounting the table top Stand Position 906-3550-005/895 Speedcontrolunit View: from the lower side Controlbox P 40 ED Drillholes for fastening the motor (Scr.
9 - 1 S et ting up 9 Setting up All instructions and regulations in this instruction manual must be observed. Special attention must be given to all safety regulations! All setting-up work must only be done by personnel with the necessary training.
9 - 2 Set ting up 109-072 9 .02 Winding the bobbin thread ● Place the empty bobbin 1 on bobbin winder spindle 2 . ● Thread the thread as shown in Fig. 9-03 and wind it around the bobbin a few times in a clockwise direction. ● Adjust the thread tension by turning knurled screw 3 .
9 - 3 S et ting up 109-023 9 .03 Changing the bobbin on the PFAFF 1122-720/02 Fig. 9 - 04 2 1 Switch off the machine! Danger of injury if the machine is started accidentally! Removing the bobbin case ● Raise the take-up lever to its top position. ● Open the cover of the hook compartment, raise latch 1 and remove bobbin case 2 .
9 - 4 Set ting up 109-095 109-061 9 .04 Changing the bobbin (on machines with drop-in hook) Fig. 9 - 06 Switch off the machine! Danger of injury if the machine is started accidentally! ● Raise the take-up lever to its top position. ● Open the cover of the hook compartment, raise latch 1 and remove empty bobbin 2 .
9 - 5 S et ting up 9 .05 Threading the needle thread / adjusting the needle thread tension Switch off the machine! Danger of injury if the machine is started accidentally! ● Thread the needle thread as shown in Fig. 9 - 08 . ● Regulate the needle-thread tension by turning milled screw 1 or 2 .
9 - 6 Set ting up 9 .06 Adjusting the stitch length ● Set the desired stitch length with adjustment wheel 1 . Fig. 9 - 09 9 .07 Entering start and end backtacks (only on machines with Quick motor) ● Switch on the machine. ● If necessary switch off the "darning seam" or "counted seam" function.
9 - 7 S et ting up ● By pressing the corresponding +/- key , set the number of stitches which can be sewn with one bobbin. The selected value is multiplied by 200 and this gives the number of stitches. Example display text 20 x 200 = 4000 stitches. ● Store the input by concluding the parameter input.
10 - 1 Care and maintenance 10 Care and maintenance 10 .01 Maintenance intervals Clean the entire machine .............................................................................. once a week Clean the hook compartment .................... once a day, or more often if in continuous use Oil the machine .
10 - 2 Care and maintenance 109-080 10 .03 Cleaning the hook compartment Fig. 10 - 01 Switch off the machine! Danger of injury if the machine is started accidentally! ● Open the hook compartment covers. ● Remove the bobbins or bobbin cases. ● Clean the hook and hook compartment.
10 - 3 Care and maintenance 10 .04 Oiling the machine Fig. 10 - 03 Switch off the machine! Danger of injury if the machine is started accidentally! ● When required fill in oil through hole 1 to the top marking of gauge glass 2 . ● In addition apply a few drops of oil once a week to the spots marked, see arrows in Fig.
10 - 4 Care and maintenance 109-092 10 .05 Oiling the hook race Switch off the machine! Danger of injury if the machine is started accidentally! ● Before commissioning the machine and after long downtimes also apply a few drops of oil to the hook race, see arrow in Fig.
10 - 5 Care and maintenance 10 .07 Oil disposal ● When required, unscrew oil collector 1 and dispose of the oil in accordance with the valid local environmental regulations. The oil must not get into the sewer system! Danger of damage to the environment! Fig.
11 - 1 W earing par ts System DPx5 JSS-70804040 (2x) JSS-6090440 (2x) JSD-6090540 JSS-61 1 0640 (2x) JB5-1 040502 JSS-70807 44 11 Wearing parts This is a list of the most important wearing parts. A detailed parts list for the complete machine is included with the accessories.
11 - 2 W earing par ts J50 1BJ1 0 1 J50 1GF1 08 J20 1 -2970 (1 1 22 A, B) J21 1 -0940 (1 1 22-90 0 A, B , C) J202-2970 (1 1 22 C) J203-0 1 80 (1 1 22-G A, B , C) J20 1 -1 180 (1 1 22) J203-0060 (1 1 2.
PF AFF Industriesysteme und Masc hinen AG Hans-Geiger -Str . 1 2 - IG Nord D-67 661 Kaiserslautern Phone: +49 - 631 20 0-0 Fax: +49 - 631 1 7202 E-mail: info@pf aff-industrial.
デバイスPfaff 1122-Gの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pfaff 1122-Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPfaff 1122-Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pfaff 1122-Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pfaff 1122-Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pfaff 1122-Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPfaff 1122-Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pfaff 1122-Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPfaff 1122-Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。