Pharos Science & Applicatiメーカーons iGPS-BT IIの使用説明書/サービス説明書
ページ先へ移動 of 16
iGPS-BT II User Manual.
FCC Notices This device complies with Part 15(b and c) of the FCC Rules. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, includin g interference that may cause undesired operation.
I. iGPS-500 Receiver and Bluetooth Dock iGPS-BT II Dock iGPS-500 Receiver DC Jack for charging On/Off Swit ch Battery charging indicator (Orange/Green LED) Bluetooth Status Indicator (Internal Blue LED) DC Jack - Plug either the Car charger or 5V AC adapter for your PDA into the DC Jack to charge the battery.
II. iGPS-BT II Setup (see walkthrough guides at the end of this section) 1. The iGPS-BT II will need to be charged for two to three hours before initial use. 2. Turn on the iGPS-BT II. The status indicator will blink as it searches for a Bluetooth connection.
Walkthrough Guides 1. iGPS-BT II Setup for Pocket PCs wit h built-in Bluetooth Technology running the Windows Mobile Pocket PC OS (the following screen shots show the device as “ Pharos iGPS-BT ”, it may be shown as “ Pharos BT GPS II ” on your Pocket PC.
5. Provided that your iGPS-BT II is turned on and fully charged, it will be discovered. Tap on the “ Pharos iGPS-BT ” icon to select it 6. Enter the Passkey: 12345678 , and select “ OK” in the upper right-hand corner 7. Select “ GPS RFcom ” so that it becomes highlighted, and tap on “ Next ” 8.
9. Tap and hold on the “ Pharos iGPS- BT: GPS RFcom ” icon, select “ Connect ” from the Menu that appears 10. Once the GPS has a connection, the icon will change to Green. You will also notice that the Blue light on the GPS itself is now a solid, steady Blue.
13. Now that the COM Port is setup, you can Enable the GPS by tapping on the RED Smiley face 14. Select “ YES ” to Enable the GPS Bluetooth setup for Windows Mobile 5.
2. iGPS-BT II Setup for Pocket PCs with built-in Bluetooth Technology running the Windows Mobile 5.0 OS (the following screen shots show the device as “ Pharos iGPS-BT ”, it might be shown as “ Pharos BT GPS II ” on your Pocket PC.) 2. Click the small Bluetooth icon the bottom right-hand side of the screen.
6. Enter the passkey: 12345678 7. Put a check mark in the box next to “serial port” and tap Finish 8. Next select the “COM Ports” tab at the bottom of the screen. Then select “New Outgoing Port” 9. Select the “Pharos iGPS-BT” and tap, Next.
10. Select Com 7, and make sure that there is a check in the “Secure Conne ction” b ox and tap Finish. 11. Close down the Bluetooth Settings screen and start the Pharos Ostia navigation program.
….. ….. 14. The Smiley Face should go from Red to Yellow when searching for satellites and finally to Green when a GPS lock for navigation has been established . For Bluetooth setup on other devices, please visit: www.pharosgps.com for walkthrough guides under the Support section.
Battery Precautions (w: WARNING!) 1. w Reverse charging is not acceptable. 2. Charge before use. The cells /batteries are delivered in an uncharged state. 3. w Do not charge/discharge with mo re than our specified current (400mA). 4. w Do not short circuit the cell/ battery, permanent damage to the cell/battery may result.
IV. iGPS-BT II GPS Receiver Specifications Performance Chipset SiRF StarIII GSC3f Antenna Integrated patch antenna Frequency L1, 1575.42 MHz Sensitivity -159 dBm Channels 12 Channel a ll-in-view tracking Acquisition time Cold Start: 35 sec (open sky) Hot Start: 1 sec (open sky) Reacquisition 0.
V. Precautions • Position fixing may not be available w hen this receiver is used near high- voltage wire, electronics equipment that generates electrical noise, or mobile phones in operation at 1.5 GHz. The noise from PDA or PC may deteriorate the GPS receiver performance.
VIII. Troubleshooting For any troubleshooting assistance, please check the Frequently Asked Questions section at www.pharosgps.com. IX. Warranty The iGPS-BT II Receiver is warranted by Pharos to the o.
デバイスPharos Science & Applications iGPS-BT IIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Pharos Science & Applications iGPS-BT IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPharos Science & Applications iGPS-BT IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pharos Science & Applications iGPS-BT IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pharos Science & Applications iGPS-BT IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pharos Science & Applications iGPS-BT IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPharos Science & Applications iGPS-BT IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pharos Science & Applications iGPS-BT IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPharos Science & Applications iGPS-BT IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
