AT&TメーカーE5815の使用説明書/サービス説明書
ページ先へ移動 of 36
User Manual (P ar t 2) 5.8 GHz Cor dless T elephone/Answ ering System E5815 with Caller ID & Call W aiting 91-000091-020-000.E5815.RO.qxd 2/13/1950 7:21 PM Page 1.
Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. STOP! See page 7 for easy instructions. You must install and charge battery before using the telephone.
1 T ab le of contents Getting Started Quick reference guide ........................2 Parts checklist .......................................4 Before you begin ..................................5 Telephone base installation................6 Battery installation & charging .
2 Getting Started Off/Clear During a call, press to hang up. While using menus, press to cancel an operation, back up to the previous menu, or exit the menu display. Quick r eference guide Mute/Delete Press to mute microphone (see page 11). While reviewing call log, press and hold to clear Caller ID log (see page 19).
Answering System Controls (see pages 20-28) ON/OFF ..................Press to turn answering system on or off. DELETE ..................Press to delete message. Hold to delete all old messages. TIME SET ................Press to review or set the answering system clock.
4 Getting Started P ar ts checklist Remember to save your sales receipt and original packaging in case you ever need to ship your telephone for warranty service.
5 Getting Started Befor e y ou begin About Caller Identification Caller ID with Call Waiting features in this telephone let you see who’s calling before you answer the phone, even when you’re on another call. These features require services provided by your local telephone company.
NOTE: Use only the power cord supplied with this product. If you need a replacement, call 1-800-222–3111. Be sure to use an electrical outlet not controlled by a wall switch. 6 Getting Started T elephone base installation Install the telephone base as shown below.
7 Getting Started Batter y installation & charging After installation, place the handset in the base and allow to charge for 12 hours before use. You can keep battery charged by returning the handset to the base after each use. When battery is fully depleted, a recharge takes about 10 hours.
8 Getting Started W all mounting The speakerphone base can be installed on any standard wall-phone outlet as shown below. Choose a location away from electronic equipment, such as personal comput- ers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture.
9 Getting Started Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset.
10 Telephone Operation Basic operation Making and answering calls To answer an incoming call, press PHONE (or SPEAKER, or any dial pad key). To make a call, press PHONE or SPEAKER , then dial a number. Press OFF or place the handset in the base to hang up.
11 Telephone Operation Options while on calls Volume control Press VOLUME buttons on the side of the handset to adjust listening volume. Each button press raises or lowers volume by one level. When you change the volume level, the new setting becomes the default.
Handset settings At the feature menu you can change settings to customize how the telephone works. Press MENU , then use the ^V buttons to scroll to the feature you want to change. As you scroll through the menu, the top menu item is always highlighted with a > character.
13 Telephone Operation Handset settings Handset name At this menu you can customize the name that appears on the handset screen when the phone is idle. Press DELETE to erase letters, then replace them with a name of your preference, up to 16 characters long (see page 15 to enter letters).
14 Phonebook Memory capacity The phonebook directory can store up to 50 entries. Each entry can contain a number up to 32 digits, and a name up to 16 letters long.
15 Phonebook New phonebook entries To create a new phonebook entry Press MENU twice to select DIRECTORY . Press V to highlight STORE . Press SELECT , then enter the telephone number when prompted. Use the dial pad to enter up to 32 digits, then press SELECT.
16 Phonebook Phonebook sear ch Press DIR to display the first listing in the phonebook. You can then use the up/down arrows to browse through the phonebook, or search to find a specific entry. Press OFF at any time to exit the directory. To browse through the directory To browse, press ^ or V to scroll through all entries one by one.
17 Phonebook T o dial, chang e or delete entries To dial a number When any phonebook entry is displayed, press PHONE (or SPEAKER ) to dial the displayed number. To delete an entry When any phonebook entry is displayed, press DELETE to delete the displayed entry from the phonebook.
18 Caller ID Logs How Caller ID works If you subscribe to Caller ID service provided by your local phone company, information about each caller will be displayed after the first ring. Information about the last 50 incoming calls is stored in your call log.
19 Caller ID Logs T o r evie w y our call log To review your call log Press CID to review your call log. The most recent call is displayed first. Use the arrow buttons to scroll through the list as shown at left. To return a call Press PHONE (or SPEAKER ) to call the number as displayed.
20 Answering System Operation Message capacity The answering system can record up to 99 messages, depending on the length of each message. Individual messages can be up to 4 minutes long, but total maximum recording time is 15 minutes. Messages will remain available for replay until you delete them.
21 Answering System Operation Da y and time announcements To set day and time Before playing each message, the answering system announces the day and time the message was received. Before using the answering system, you should follow the steps at left to set the day and time, so messages are dated correctly.
22 Answering System Operation Outgoing announcements Outgoing announcements are the messages callers hear when calls are answered by the answering system. The phone is pre-programmed with an announcement that answers calls with “Hello. Please leave a message after the tone.
23 Answering System Operation Announce Only mode In Announce Only mode, callers hear an announcement but cannot leave messages. This option is useful, for example, to notify callers that you will be away for an extended period and request that they call back after a certain date.
24 Answering System Operation Changing featur e options Menu features can be changed to customize how the answering system operates. Press MENU repeatedly to hear each feature. Press CHANGE when you hear the feature you want to modify. Feature options (Default settings underlined).
25 Answering System Operation Messag e pla yback Press PLAY/STOP to hear messages. The system announces the number of messages, then begins playback. If you have new messages waiting, you will hear only the new messages (oldest first). If there are no new messages, the system will play back all messages (oldest first).
26 Answering System Operation Recording and pla ying memos Memos are messages you record yourself. They are saved, played back and deleted exactly like incoming messages. You can record a memo as a reminder to yourself, or leave a message for someone else if others in your household use the answering system.
27 Answering System Operation Messag e windo w displa ys The message window usually displays the total number of memos and incoming messages. See the list below for explanations of other displays in this window.
28 Answering System Operation 1 Remote access A 2-digit security code is required to access your answering system from any touch-tone phone. This code is “19” by default; see page 24 to change it. Dial your telephone number from any touch-tone phone.
29 Appendix Scr een icons, indicator lights & tones Handset screen icons & alert tones Speakerphone in use. Ringer off. Battery charging (animated display). Low battery (flashing); place handset in base to recharge. MUTE SPEAKER Microphone is muted.
30 Appendix In case of difficulty If you have difficulty with your phone, please try the suggestions below. For Customer Service, visit our web site at www.telephones.att.com , or call 1-800-222–3111. Telephone does not work at all • Make sure battery is installed and charged correctly (see page 7).
31 Appendix Incomplete messages • If a caller leaves a very long message, part of it may be lost when the system disconnects the call after 4 minutes. • If the caller pauses for more than 7 seconds, the system stops recording and disconnects the call.
T echnical specifications RF Frequency Band (Handset to Base) 2401.056 MHz - 2482.272MHz Output Power handset 20 dBm, base 30dBm Sensitivity -96 dBm Modulation GFSK RF Frequency Band (Base to Handset) 5744.
33 Appendix A AC adapter, 6 Alert tones, 29 Answering calls, 10 Answering system, 20-28 B Battery charging, 7 Battery installation, 7 Belt clip, 9 C Caller ID, 18 add entries to phone directory, 19 de.
Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 2 AT&T 01/05. 91-000091-020-000 www .telephones.
デバイスAT&T E5815の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
AT&T E5815をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAT&T E5815の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AT&T E5815の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AT&T E5815で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AT&T E5815を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAT&T E5815の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AT&T E5815に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAT&T E5815デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
