ATEN TechnologyメーカーCL-1200の使用説明書/サービス説明書
ページ先へ移動 of 34
User Manual CL-1200 cl1200_v2.book Pag e i Friday, March 10, 2006 1 :43 PM.
CL-1200 User Manual ii FCC Information This is an FCC Class A product. In a domestic environment this product may cause radio interference in which cas e the user may be required to tak e adequate measures. This equipment has been test ed and found to comply with the limit s for a Class A digital device, pursuant to Part 15 of the FCC Rules.
CL-1200 User Manual iii User Notice All information, docum entation, and specifications contained in this manual are subject to change without prior no tification by the manufacturer.
CL-1200 User Manual iv Safety Instructions General Read all of these instructions. Save them for future reference. Follow all warn ings and instru ctions marked on the device. Do not place the device on any unstable su rface (cart, stand, table, etc.
CL-1200 User Manual v Position system cables and power cable s carefully; Be sure that nothing rests on any cables. When connecting or d isconnecting power to hot-pluggab le power supplies, observe the foll owing guidelines: Install the powe r su pp l y before connecting the power cable to the power supply .
CL-1200 User Manual vi Rack Mounting Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor , and that the full weight of the rack rests on the floor . Install front and side stabilizers on a singl e rack or front stabilizers for joined mu ltiple r acks before working on the rack.
CL-1200 User Manual vii Package Contents Basic Package The basic CL-1200 package consists of: 1 CL-1200 KVM Console with Standard Rack Mounting Kit 1 Custom KVM Cabl e Se ts 1P o w e r C o.
CL-1200 User Manual viii This Page Intentionally Left Blank cl1200_v2.book Pag e viii Friday, March 10, 2 006 1:43 PM.
CL-1200 User Manual ix Content s FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii User Notice .
CL-1200 User Manual x Appendix Optional Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Troubleshooting . . . .
CL-1200 User Manual xi About this Manual This User Manual is provided to help you get the most from your c/c system. It covers all aspects of installation, configurati on and op erati on. An overview of the information fou nd in th e manual is provided below.
CL-1200 User Manual xii Conventions This manual uses the following conven tio ns: Getting Help If you need to contact ATEN techni cal support with a problem , visit or website at www.aten.com . Monospaced Indicates text that you should key in. [ ] Indicates keys you should press.
1 Chapter 1. Introduction Overview The CL-1200 is a KVM console module f eaturing an integrated 15" or 17" LCD panel, full keyboard, and touchpad in a 1U, rack-mou ntable, Slideaway™ housing. It was developed in response to th e enorm ous pop ularity of the Slideaway™ console found on the CL-1208 and CL-1216 KVM swit ches.
CL-1200 User Manual 2 Features Integrated KVM console with 15"or 17" LCD monitor - in a Slideaway ™ housing Slideaway ™ housing is less than 1U - with top and bottom clearance fo.
1. Introduction 3 Hardware Requirement s Computers The CL-1200 supports most Master V iew KVM switches that have PS/2 console port connectors. If yo u are unsure whether your switch is supported or not, check with yo ur d ealer or call Aten Customer Service.
CL-1200 User Manual 4 Component s Front V iew No. Component Descript ion 1 Handle Pull to slide the KVM module ou t; push to slide the module in. 2 Slide Release In order to slide the cons ole out, you must first release it by moving this tab sideways.
1. Introduction 5 Rear View No. Component Description 1 Power Socket This is a standard 3 pron g AC power socket. The power cord from your AC source plugs in here.
CL-1200 User Manual 6 This Page Intentionally Left Blank cl1200_v2.book Pag e 6 Friday, March 10, 2006 1 :43 PM.
7 Chapter 2. Inst allation Before you Begin S t andard Rack Mounting A standard rack mounting kit is pro vided with y our CL-1200. The kit enables the switch to be mounted in rack with a depth of 42 - 72 cm. Note: It takes two people to mount the switch : one to hold it in place; the other to screw it in.
CL-1200 User Manual 8 To rack mount the switch, do the following : 1. While one person positions the switch in the rack and hold s it in place, the second person - using the screws provided with the rack mounting kit - loosely screws the front brackets to the rack.
2. Installation 9 Connecting Up Refer to the example installation diagram on the next page as you perform the following steps: 1. Plug the 15 pin connector end of the KVM cable provid ed with this unit into the CL-1200's KVM port.
CL-1200 User Manual 10 Note: The example diagram shows the CL-1200 connecting to an ACS-121 6A KVM switch, but th e CL-1200 can connect to m ost A TEN KVM switches that have PS/2 port cons ole connectors. If you are connectin g to a different model, the console po rt connectors may be in a different location.
11 Chapter 3. Operation Opening the Console The CL-1200's console is located under the top cove r. To access the console, slide the console module out and raise the cover. Note: As a safety precaution, to keep th e console from accidentally s liding out, the console is locked into the In po si tio n.
CL-1200 User Manual 12 Closing the Console To slide the console module back in , close the cover and do the following: 1. Pull the safety catches on the unit's side rails toward you and push the module in unti l it stops. 2. Release the catches; pull the module sli ghtly toward you; then push it all the way in.
3. Operation 13 Operating Precautions Right! Rest your hands and arms lightly on the keyboard module as you work. Wro ng ! DO NOT lean your body weight on the keyboard module. DO NOT place heavy objects on the keyboard module. The maximum load bearing capacity of the keybo ard m odu le is 30kg.
CL-1200 User Manual 14 LCD OSD Configuration The LCD Buttons The LCD OSD allows you to set up and configure the LCD display. Four buttons are used to perform the co nfigura tion, as described in the t.
3. Operation 15 The Adjustment Settings An explanation of the LCD OSD adjustment settings is given in the table below: Setting Explanation Brightness Adjusts the background bl ack level of the screen image. Contrast Adjusts the foreground white level of the screen image.
CL-1200 User Manual 16 Console Selection Console selection on the CL-1200 is acco mplished with hotkey combinations, as described in the following table: Note: 1. Press the keys in sequence - o ne key at a time. First [Ctrl], then [Alt], then [Shift], etc.
17 Appendix Optional Rack Mounting For convenience and flexibili ty, three optional rack mounting kits are available: A long bracket standard rack mount ing kit fo r 68.0 - 100.0 cm racks; A short bracket Easy-Ins tallatio n rack mount kit for 42 .
CL-1200 User Manual 18 2. Attac h th e lef t and right easy-installation moun ting rails to the inside of the rack. The flange that supports the switch will be to the inside.
Appendix 19 3. Slide the switch onto the support flanges. Use the screws supplied with this package to loosely attach the front of the switch to the front of the rack (only tighten the screws part way).
CL-1200 User Manual 20 5. Slide the switch open and closed a coup le of times to be sure that it is properly aligned and operating smoo thly . (See p. 1 1 for opening and closing procedures.
Appendix 21 Specifications Function Specificati on Connectors KVM Ports 1 x SPHD-15 F External Console 1 x 6 pin mini-DIN F (keyboard) 1 x 6 pin mini-DIN F (mouse) 1 x HDB-15 F (monitor) Power 3 prong.
CL-1200 User Manual 22 T roubleshooting Problem Solution There are ghost images on the external monitor . The distance between the external console and th e CL- 1200 is too great. The maximum cable distance should not exceed 20m and, in some cases, may need to be shorter .
デバイスATEN Technology CL-1200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ATEN Technology CL-1200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはATEN Technology CL-1200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ATEN Technology CL-1200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ATEN Technology CL-1200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ATEN Technology CL-1200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はATEN Technology CL-1200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ATEN Technology CL-1200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちATEN Technology CL-1200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
