PioneerメーカーDVD-204の使用説明書/サービス説明書
ページ先へ移動 of 20
Instruction Manual Models DVD-204 and DVD-212 Control Units for Pioneer DVD Players New with V ersion 2.03 On-Screen Programming See Addendum at back of this manual Issued Febrary 2002 Revised May 2003 Museum T echnology Source, Inc. 323 Andover S treet Wilmington Massachusetts 01887 phone 800.
SETUP SHEET DVD-204 AND DVD-212 CONTROL UNITS FOR USE WITH PIONEER DVD PLAYERS Introduction: The DVD-204 and DVD-212 are controllers for use with the Pioneer DVD-7200 and DVD-7400 Industrial DVD Players. The DVD-204 and DVD-212 are identical except for the number of selection pushbuttons: 4 vs 12.
Connection to the external pushbuttons is made via standard telephone RJ-1 1 modular connectors. T wo of the 4 wires (Green and Red) are used to start the selection, while the other two wires (Y ellow and Black) provide 12 volts DC to illu- minate the pushbutton lamp.
MENU PAGE 1 /2 WEEKLY TIMER OFF POWER ON START T01:C01 TITLE PLAY MODE SINGLE REPEAT MODE OFF BAUD RATE 9600bps TRAY LOCK OFF STILL MODE FIELD D.R. COMP OFF MENU PAGE 2 / 2 MARK FRAME SQUELCH OFF SQUE.
Configuring the computer used for programming: Double click on the Hypertrm.exe icon. The program will open with a New Connection dialog box, with the instruction to enter a name and select an icon. Enter a name of your choosing, such as DVD-204, or the name of the product you are about to program.
Museum Technology Source, Inc. DVD Controller model DVD-204 Player: Pioneer DVD-V7200/7400 Firmware version 1.22 (C)2000 Museum Technology Source Inc. For further information contact: Museum Technology Source Inc. 323 Andover Street Wilmington, MA 01887 Phone: (800)729-6873 or (978)657-7132 Fax: (978) 657-7132 Email: info@museumtechnology.
Button 1 plays from frame 12 to frame 600. ———- Main Menu ———- A = select address mode (FRAME, CHAPTER, or CHAPTER start/FRAME end) B = view or edit a Button’s selection I = view or edit.
Please choose a command: T Testing buttons and lamps. Type any letter to stop. Button 1 pressed...released. Button 2 pressed...released. Button 3 pressed.
interruptible, a safe time can be set, specifying the minimum amount of time before a selection can be interrupted. Selections are now interruptible after 0 seconds. Do you want to change this (Y/N)? Yes Do you want button selections to be interruptible (Y/N)? No *** Programming: done *** Selections are now uninterruptible.
This completes the programming of the control unit. Unplug the Programming Cable from the back of the unit, and store it away for the next programming session.
Rear Panel Connections, DVD-204 and DVD-212.
ON-SCREEN PROGRAMMING Addendum to DVD-204 / DVD-212 Manual Effective with version 2.03, most programming tasks can be accomplished without having to connect the DVD-204 /DVD-212 to a computer. Using only a DVD-204 /DVD-212, a Pioneer 7200 /7400 DVD player, and a video monitor, it is possible to program the DVD-204 /DVD212.
Upon pressing button 1, the following message will appear on the screen: Press the BUTTON you would like to VIEW or EDIT : > Press a Button < In this example let's say that we wish to program button number 3; we simply press button 3 to do so.
At this point, you may use the Pioneer DVD player's con- trols as you normally would, to find the exact frame on the disc to begin your button sequence. In this example, let's say frame "5678". After the start frame is located on the DVD, press button 1 on the DVD-204 /DVD-212.
is the Exit and Run command. The player will now revert to it's normal state, ready for use. You may wish to program what the DVD does between plays.
Museum Technology Source Inc. VIDEO MONITOR VIDEO MONITOR Master Player All Players Must Be Set To 9600 Baud Multi-Player Hookup SET "SLAVE DELAY" TO 1 SECOND MARCH 98 MPC Revised December 2.
323 Andover Street Wilmington, MA, 01887 800-729-6873 / 978-657-3898 Fax: 978-657-7132 www.museumtech.com / info@museumtech.com Museum Technology Source, Inc.
For Video Disc Controllers , such as the VDC-200A and VDC-212, use the same settings except the Baud Rate is 1200. Click OK. Main screen will appear and at the bottom left message “Connected” will appear.
Addendum Setup Instructions Pioneer DVD-V5000 Player April 2005 Like the Pioneer DVD-V7400 Player mentioned in the DVD-204 and DVD-212 Instruction Manual, the Pioneer DVD-V5000 Player must also be configured prior to use. In order for the player to be able to communicate with the control unit certain settings must be made.
The player is now set such that when power is applied to it, it will automatically “wake up” on Title 1, Chapter 1. Using the same technique, make the following settings: Title Play Mode Single Ke.
デバイスPioneer DVD-204の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Pioneer DVD-204をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPioneer DVD-204の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pioneer DVD-204の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pioneer DVD-204で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pioneer DVD-204を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPioneer DVD-204の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pioneer DVD-204に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPioneer DVD-204デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
