PioneerメーカーPDP-504CMXの使用説明書/サービス説明書
ページ先へ移動 of 18
PDP-504CMX Plasma Display Panel RS-232C Commands C OMMAND P ROTOCOL M ANUAL Manual Version 1.00 November 3, 2004 Pioneer Corporation Pioneer Electronics (USA) Inc.
This manual is copyrighted with all rights reserve d. No part of this document may be repri nted, produced, translated or utilized in any form or by any means now known or her eafter invented includi .
1 RS-232C Adjustment Mode 5.5 RS-232C Adjustment Mode This display has a RS-232C terminal. It is possible to use a PC to make various adjustments and settings. 5.5.1 About the RS-232C Adjustment Mode 1) Adjustments in the RS-232C adjustment mode: • The adjustments are written to the same memory area as for the integrator mode (refer to section 5.
2 RS-232C Adjustment Mode 5.5.2 Interface 1) Connector D-sub 9 pins (male) 2) Pin layout 3) Baud Rate 9600 bps (standard) (switch-able to 1200, 2400, 4800, 19200, 38400 bps) Note The baud rate of this display should be set to match the baud rate of the PC.
3 RS-232C Adjustment Mode 5.5.3 ID Assignment After connecting to the PC, an ID is assigned. The ID is assigned from the PC. Commands: <IDC> (ID CLEAR) ........ Clears the assigned ID <IDS> (ID SET) ............. Assigns an ID IDS is only effective when an ID is not assigned.
4 5.5.4 Combination Connection When performing control and adjustment, it is convenient to connect several sets to one PC. By performing a combination connection and assigning IDs to the sets, it is possible to control and adjust several sets at the same time or separately.
5 Under the connection conditions shown below, operation using a combination cable is assured up to 16 sets. Conditions: 1 Length of RS-232C cable connecting PC to PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S: .
6 RS-232C Adjustment Mode 5.5.5 List of RS-232C Commands How to read this Table • RS-232C adjustment validity : Indicates whether or not the RS-232C adjustment mode can be used. • Normal validity : Indicates whether or not the normal-operation mode can be used.
7 RS-232C Adjustment Mode CTR CTI: ### Displays the current CTI setting. ¶ CTRS00 CTI: OFF Sets CTI to OFF. ‡ CTRS01 CTI: ON Sets CTI to ON. ‡ [D] DIN Turns OFF the OSD display. ‡‡ DIY OSD: ON Turns ON the OSD display. ‡‡ DNR DNR: ###### Displays the current DNR setting.
8 RS-232C Adjustment Mode GRA GRADATION: ####### Displays the current GRADATION setting ¶ GRAS01 GRADATION: GAMMA 2.0 Sets GRADATION to ‘ GAMMA 2.0 ’ . ‡ GRAS02 GRADATION: GAMMA 1.8 Sets GRADATION to ‘ GAMMA 1.8 ’ . ‡ GRAS03 GRADATION: GAMMA 2.
9 RS-232C Adjustment Mode MIR MIRROR MODE: ### Displays the current MIRROR MODE setting. ¶ MIRS00 MIRROR MODE: OFF Turns the MIRROR MODE OFF (normal display). ‡ MIRS01 MIRROR MODE: X Sets the MIRROR MODE to left-right reversal. ‡ MIRS02 MIRROR MODE: Y Sets the MIRROR MODE to up-down reversal.
10 RS-232C Adjustment Mode SSI ######### Displays the current sub screen input function. ¶¶ SSIS01 INPUT1(SUB) Switches the sub screen to INPUT1. ‡‡ SSIS02 INPUT2(SUB) Switches the sub screen to INPUT2. ‡‡ SSIS03 INPUT3(SUB) Switches the sub screen to INPUT3.
11 RS-232C Adjustment Mode 5.5.6 GET Commands What are GET commands? • They are commands for outputting TXD such as adjustment data from the internal microcomputer of the plasma display to a PC. • Adjustment data and the like is output in ASCII code.
12 RS-232C Adjustment Mode 2) <GPI> (GET PICTURE DATA: Gets integrator/PICTURE data.) Order Data contents Size Remarks 1 CONTRAST 3 Byte # 2 BRIGHTNESS 3 Byte # 3 C. DETAIL R (RED) 3 Byte # 4 C. DETAIL Y (YELLOW) 3 Byte # 5 C. DETAIL G (GREEN) 3 Byte # 6 C.
13 RS-232C Adjustment Mode 5) <GSS> (GET STATUS SETUP: Gets menu and integrator SETUP data.) Order Data contents Size Output Remarks 1 GRADATION 1 Byte 1: GAMMA 2.0 2: GAMMA 1.8 # 3: GAMMA 2.2 4: DRE MID 5: DRE HIGH 6: DRE LOW 7: HIGH CNT. 2 BRT.
14 RS-232C Adjustment Mode 6) <GSO> (GET STATUS OPTION: Gets menu and integrator OPTION data.) Order Data contents Size Output Remarks 1 ENERGY SAVE 1 Byte 1: STANDARD 2: MODE 1 3: MODE 2 4: MOD.
RS-232C Adjustment Mode Check Sum This is data to which 2-Byte ASCII code is added to a data group returned by a GET command. PC side STX ID GET command ETX 02 (hex) 2 Byte 3 By te 03 (hex) Set side STX GET command Data Check Sum ETX 02 (hex) 3 Byte *Byte 2 Byte 03 (hex) A det ailed example will be given below .
PDP-504CMX RS-232C Command Protocol Manual Pioneer Electronics (USA) Inc. Industrial Solutions Business Group 2265 East 220 th Street Long Beach, California 90810 United States of America (310) 952-2000 http://www.
デバイスPioneer PDP-504CMXの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pioneer PDP-504CMXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPioneer PDP-504CMXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pioneer PDP-504CMXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pioneer PDP-504CMXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pioneer PDP-504CMXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPioneer PDP-504CMXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pioneer PDP-504CMXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPioneer PDP-504CMXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。