Pitco FrialatorメーカーL80-029の使用説明書/サービス説明書
ページ先へ移動 of 24
L80-029 Rev 5 10/07 IMPORTANT FOR FUTURE REF ERENCE Please complete this information and retain these instructions for the life of the equipmen t: Model #: ___________ ___________ ____ Serial #: _____.
L80-029 Rev 5 10/07 WARNING Drain the tank and ensure that appliance has cooled to room temperature before performing this upgrade. DO NOT work on a hot appliance or an appliance containing hot cooking medium; serious personal injury may occur.
1 L80-029 Rev 5 10/0 7 Theory of Operation : A natural gas burning applian ce requires roughly 10 cubic feet of air to properly combust a singl e cubic foot of gas. Minute airborne particles ent rained during this process pass t hrough the combustion sy stem and are incinerated.
L80-029 Rev 5 10/07 2 Follow this procedure for Inst allation of Self Cleaning burners and SCBS arm: a. Disconnect the control harne ss from the main gas valve and tuck it out the way to avoid damaging the harness during this procedure.
3 L80-029 Rev 5 10/07 e. Using a 1 1/16” wrench and a 7/8” wrench, loosen the brass fitting on the top of t he gas valve and disconnect the gas valve from the manifold inlet. This will allow you to drop the ga s valve down and keep it out of the way during burner replacement.
L80-029 Rev 5 10/07 4 i. Captu re the remaining burners on the SCBS Arm in the same manner as in step h, an d secure them into the appliance, taking care not t o strip the pre-threaded holes.
5 L80-029 Re v 5 10/07 NOTE: CE approved models will h ave a pressure test fitting in this location. For CE app roved models, remove this pressure test fitting using a 7/16” (12 mm) wrench.
L80-029 Rev 5 10/07 6 e. Thread the compression nut on the corrugated tubing end of the SCBS Valve Assembly onto the orifice assembly that you inserted int o the runner tube in step c and tighten with a 1/2” ( 13 mm) wrench. f. Install the orifice retainer brac ket onto the pilot bracket and SCBS Orifice assembly .
7 L80-029 Rev 5 10/ 07 b. Disconnect the wiring harne ss from the relay board mounted behind the front panel and remove the relay board and insulation pape r. Be sure to retain the screws. The existing relay boa rd may or may not have a jumper plug as shown.
L80-029 Rev 5 10/07 8 e. If the appliance you are upg rading does NOT have a Solid State Control, proceed to step f in this section. If the appliance that you are up grading has a Solid State Control,.
9 L80-029 Rev 5 10/ 07 i. Conne ct the SCBS Harness to the SCBS Valve as shown. The red and violet wires m ust be connected to the vertically oriented tabs on the valve and the green (ground) wire must be connected to the bottom, horizontally oriented tab o n the valve.
L80-029 Rev 5 10/07 10 Follow this procedure to che ck proper operation of the Pi tco Self-Cleaning Burner System: WARNING Ensure that tank is filled to t he level line with oil before turning the appliance on.
11 L80-029 Rev 5 10/0 7 appliance is in operation, or ca n be detected visually by watching t he burner flame through the air collars. The sound of the burners will be inc onsistent and the flame may ap pear to ‘peel’ off of the burner fa ce. A certain amount of flame roll o ut during ignition is normal.
L80-029 Re v 5 10/07 12 PROBLEM A . Main breaker in OFF p osition. A . Turn on Circuit Breaker to appliance. B. Gas supply turned OFF. B. Turn on gas supply to appliance. C. A ppliance unplugged. C. Plug appliance pow er cord into wall ou tlet. D. Blown con trol fuse.
13 L80-029 Rev 5 10/ 07.
L80-029 Rev 5 10/07 14.
15 L80-029 Rev 5 10/ 07.
L80-029 Rev 5 10/07 16.
17 L80-029 Rev 5 10/07.
L80-029 Rev 5 10/07 18.
19 L80-029 Rev 5 10/07.
L80-029 Rev 5 10/07 20.
21 L80-029 Rev 5 10/07 Before and After: Visual Aid The below images show a typical m odel SG14 burner assembly before and after the installation of the SCBS upgrade.
MAILING ADDRESS – P. O. BOX 501, CONCORD, NH 033 02-0501 SHIPPING ADDRESS – 10 FE RRY ST., CONCORD, NH 03 301 In th e eve nt of prob lem s wit h or qu est ion s abo ut you r orde r, plea se conta .
デバイスPitco Frialator L80-029の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pitco Frialator L80-029をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPitco Frialator L80-029の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pitco Frialator L80-029の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pitco Frialator L80-029で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pitco Frialator L80-029を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPitco Frialator L80-029の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pitco Frialator L80-029に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPitco Frialator L80-029デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。