PlanarメーカーLA2250RTPWの使用説明書/サービス説明書
ページ先へ移動 of 26
LA2250RTPW Open Frame T ouch Screen Monitor USER’S GUIDE www .planar .com.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright.
T able of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About LA2250RTPW ..................................................
Usage Notice ! W arnin g - T o prevent the risk o f fi re or shock hazards, do not expose this product to rain or moisture. ! W arnin g - Please do not open or disassemble the product as this ma y cause e l ec tri c s h oc k.
Introduction About LA2250RTPW The LA2250RTPW is a 21.5" fl at panel screen with an active matrix, thin- fi lm transistor (TFT) edge-lit LED liquid crystal display (LCD). This unit is to be used as commercial and light industrial equipment only .
3 Package Overview LCD Display Power Cord VGA Signal Cable DVI-D Cable USB Cable ( A to B ) DC Power Supply Landing Strip Bracket Screws (Quantity 4) Side Brackets.
4 Installation Product Overview • Front View • Bottom View VGA USB DC IN DVI RJ T ype.
Attaching the L-Brackets Depending on your mounting scheme, you may use the L-brackets to mount your displays onto your wall or device. Find a suitable location for attaching L-brackets. A. The left and right sides B. The top and bottom Note: Y ou will need a screwdriver to attach the L-brackets.
Side Mount For Y our Monitor This monitor can be mounted to a wooden or concrete wall with 4 screws and a pair brackets on the opposite sides (see page 5) 6 230.
Customer -Supplied Panel Material Recommendations 1. Wooden wall: Ø4.5mm thru holes for M4 screws w/nuts, or no thru holes, screws for wood 4mm. 2. Sheet metal: concealed head threaded studs M4 w/nuts. 7 RECOMMENDED CUSTOMER PANEL CUT-OUT 518.4 mm M4 214.
VESA Mount for Y our Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which de fi nes a physical mounting interface for fl at panel monitors, and corresponding with the standards of fl at panel monitor mounting devices, such as wall and table arms.
Connecting the Display (Figure 10.1) T o setup this display , please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC plug to the power connector on the monitor and the other end into an electrical outlet (10.
(Figure 10.1) 10 (Optional).
User Controls Back Panel Controls OSD Key Menu off status Menu on status Menu appear Menu disappear/return to main item Brightness Main item select up/Adjust up Contrast Main item select down/Adjust d.
How to Use the OSD Menus Icon Key Name Menu Up Down Select Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the fi ve functions in the main menu. 2. Choose the adjustment items by pressing the “Select” button.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically . Left/Right Moving screen image horizontal position to left or right.
14 Appendix T roubleshooting IIf you are experiencing trouble with the display , refer to the following. If the problem persists, please contact your local dealer or our service center .
W arning Signal If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card. Below are the three kinds of warning signals you may receive. Please check the cable connections or contact your sales representative or our service center for more information.
Product Dimensions 16 517.4 mm 313.3 mm 100.0 mm 100.0 mm 100.0 mm 106.7 mm 46.0 mm Front View Side View Back View.
Compatibility Modes Mode Resolution H-Frequency(khz) V -Frequency(hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple MacII 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA VGA 800X600 35.16 56 VESA VGA 800X600 37.88 60 VESA VGA 800X600 48.
T ouch Screen Driver Installation The LA2250RTPW is available with USB connection. The touch driver is available at www. planar .com/support for these operating systems: Windows® 7/8, VIST A, XP , 2000, CE, XP Embedded, Linux kernel 2.6.x (32 bit & 64 bit), Apple® Mac OS.
LA2250RTPW Calibration Instruction: Calibrating the touch screen in Windows 7/8: 1. T ap the Start button, Control Panel and then Hardware and Sound. 2. Under T ablet PC Settings, tap Calibrate the screen for pen or touch input. 3. On the Display tab, under Display options, tap Calibrate and then Y es to allow the program to make changes.
20.
21 LA2250RTPW Install Instruction: If you are using a PC running, Windows® 7/8, VIST A, XP , 2000, follow the instructions below: 1. Power on the PC. 2. Make sure that the USB cable is connected to the computer . 3. Visit www .planar .com/support. 4.
T echnical Support Cables and Accessories To fi nd cables and accessories for your Planar monitor , touch screen or other Planar products visit our online store at www .
Planar Systems, Inc. Customer Service 24x7 Online T echnical Support: http://www .planar .com/ support 1 195 NW Compton Drive Beaverton, OR 97006-1992 T el: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day , 7 days a week © 2013 Planar Systems, Inc.
デバイスPlanar LA2250RTPWの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Planar LA2250RTPWをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanar LA2250RTPWの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planar LA2250RTPWの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planar LA2250RTPWで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planar LA2250RTPWを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanar LA2250RTPWの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planar LA2250RTPWに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanar LA2250RTPWデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。