PlanarメーカーPT120の使用説明書/サービス説明書
ページ先へ移動 of 20
PLANAR LCD MONITOR PT120/PL120 MANUAL www.planar.com.
Preface P REFACE About this manual This manual is designed to assist you in setting up and using the LCD monitor. Inform ation in this document has been carefully checked for accuracy; how ever, no guarantee is given to the correctness of the contents.
User’s Manual • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Preface Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the LCD Monitor screen, first, make sure the Monitor is in the power off mode. Unplug the Monitor from its power source before cleaning it.
User’s Manual T ABLE OF C ONTENTS PREFACE ........................................................................................................................................................................ I TABLE OF CO NTENTS .................
Chapter 1 C HAPTER 1 The LCD Monitor Your New LCD Monitor! Your LCD Monitor has been designed to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640 x 480 VGA to 1024 x 768 XGA.
User’s Manual Identifying Components The LCD Monitor has been designed to provide easy access to all controls and peripheral ports. The follow- ing figures will help you identify the LCD Monitor’s controls and ports.
Chapter 1 The LCD Monitor — Rear View Figure 1-2: LCD Monitor’s Rear Ports LCD Monitor’s VGA Connector This 1.5 meter cable has two 15-pin D-Sub VGA connectors used to connect the monitor to your PC’s VGA card. AC Power Jack Connect the AC adapter cable to this jack.
User’s Manual Adjusting the Viewing Angle Your LCD Monitor is designed to allow you to adjust it to a comfortable viewing angle. The LCD Moni- tor’s angle setting range is from -5 ° to 25 ° .
Chapter 1 Figure 1-5: Connecting Power to the LCD Monitor Connecting Video Turn off your PC and the LCD Monitor before connecting your LCD Monitor to the com- puter. Connect the VGA signal cable to the D-sub VGA connector located at the rear of the monitor.
User’s Manual Connecting the Stereo Speakers (optional) Please refer to the following instructions for connecting the LCD Monitor’s stereo speakers. Connect the 1.5M sound cable to the Line out of your PC’s audio card. Connect the other end of the 1.
Chapter 1 Connect the 9-pin RS232 connector end of the PS/2 to RS232 cable provided with the op- tional touch screen package to the 9-pin RS232 serial port at the back of your PC. Please refer to Figure 1-8. Power Management System The LCD Monitor complies with the VESA DPMS (version 1.
C HAPTER 2 The Display Controls The LCD Monitor’s Display Controls This chapter covers the LCD Monitor’s On Screen Display (OSD). Using the OSD, you can adjust the con- trast, brightness, display position, display clarity, and color temperature. You can also adjust the stereo speaker volume and set OSD parameters.
Chapter 2 (Basic Setting) (CONTRAST) To adjust the contrast level of the display. (BRIGHTNESS) To adjust the brightness level of the display. (VOLUME) To adjust the speaker audio volume. (Exclude 12.1 Inch) (POSITION) (AUTO-ADJUST) To automatically adjust the picture quality and alignmen t.
User’s Manual Note: 1. No Signal coming When the monitor is ON and there is no Video signal re- ceived, the following message will be displayed. 2. Signal out of monitor’s supported ra nge (Please.
A PPENDIX A Technical Information TFT LCD Monitor Specifications Model MT121/MT121T LCD Panel 12.1”SVGA Co nt ro l Functions Po we r So ft wa r e P ow er s wi tc h wi th L ED in di c at or (Press to turn off, over 1 sec.
A PPENDIX B Supported Timing Timing for Model PT1212N (SVGA Resolution) Item Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) 1 NEC PC98 640x400 25.20 70.15 31.50 2 NEC PC98 640x400 21.05 56.42 24.
A PPENDIX C Troubleshooting Troubleshooting Procedures This LCD Monitor was pre-adjusted in the factory with standard VGA timing. Due to output timing differ- ences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected.
User’s Manual 14 If the PC doesn’t function with the CRT monitor neither, check BIOS to see if there is a dual scan setting under the display mode item. Set the BIOS display m ode to Dual Scan or CRT and try again. If there is still no display, then there may be a problem with your system .
3ODQDU6 VWHP V,QF Customer Service E-mail: desktopmonitors@planar .com T el: 1-866-PLANAR-1 (1-866-752-6271) Hours: M-F , 7am - 6pm Pacific T ime © 2002 Planar Systems, Inc. 0 5 /02 Planar is a registered trademark of Planar Systems, Inc.
デバイスPlanar PT120の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Planar PT120をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanar PT120の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planar PT120の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planar PT120で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planar PT120を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanar PT120の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planar PT120に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanar PT120デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。