PlanarメーカーPT1945Sの使用説明書/サービス説明書
ページ先へ移動 of 30
PT1945R / PT1945S / PT1945P T ouch Screen Monitor USER’S GUIDE www .planar .com.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright.
T able of Contents Usage Notice Precautions ................................................................................................................... ......... 1 Introduction About PT1945R/PT1945S/PT1945P ....................................
Usage Notice ! W arnin g - T o prevent the risk o f fi re or shock hazards, do not expose this product to rain or moisture. ! W arnin g - Please do not open or disassemble the product as this ma y cause e l ec tri c s h oc k.
Introduction About PT1945R/PT1945S/PT1945P The PT1945R/PT1945S/PT1945P is a 19" fl at panel screen with an active matrix, thin- fi lm transistor (TFT) edge-lit LED liquid crystal display (LCD). This unit is to be used as commercial and light industrial equipment only .
3 T ouch Screen for PT1945R • Analog 5-wire resistive touch screen for fi nger and stylus input • Surface: Anti-glare treatment • Interface: Dual RS-232 Serial/USB controller • Transmittance: 82%±5% • HID: Windows® 7/8 • Driver: Windows ® 7/8, VIST A, XP , 2000, ME, 98, NT 4.
Package Overview Display Power Cord VGA Signal Cable RS-232 Cable (PT1945R/PT1945S only) USB Cable ( A to B) Audio-in Cable Landing Strip User ’s Guide xxxxxxxxx / xxxxxxxxx xxxxxxxxx USER’S GUIDE www.
Installation Product Overview • Front View • PT1945R/PT1945S Bottom View (W ithout Stand) • PT1945P Bottom V iew (Without Stand) 5 RS-232 VGA AC IN USB POWER SWITCH AUDIO PT1945R/PT1945S PT1945P.
6 Start Y our Installation Please follow these instructions so that you can hookup the cables to associated connector . 1. Lay the display fl at on an even surface. 2. Move the stand into position as seen in the step 2 diagram. 3. Remove the cable cover as seen in the step 3 diagram.
Connecting the Display (Figure 8.1) T o setup this display , please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (8.
(Figure 8.1) PT1945R/PT1945S PT1945P 8.
Kensington Security Slot The monitor can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included.
VESA Mount Y our Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which de fi nes a physical mounting interface for fl at panel monitors, and corresponding with the standards of fl at panel monitor mounting devices, such as wall and table arms.
Remove the Deskstand 11 Remove 4 screws and then remove hinge..
User Controls Side Panel Controls OSD Key Menu off status Menu on status Menu appear Menu disappear/ return to main item Brightness Main item select up/ Adjust up Mute Main item select down/ Adjust do.
How to Use the OSD Menus Icon Key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu. 2. Choose the adjustment items by pressing the “Enter ” button.
14 On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically . Left/Right Moving screen image horizontal position to left or right.
Appendix T roubleshooting If you are experiencing trouble with the display , refer to the following. If the problem persists, please contact your local dealer or our service center .
16 W arning Signal If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card. Below are the three kinds of W arning Signal. Please check the cable connections or contact your local dealer or Planar for more information.
Product Dimensions PT1945R/PT1945S 17 431.8 mm 390.9 mm 358.0 mm 249.6 mm 219.0 mm 212.0 mm 67.0 mm ► Side View ► T op View ► Front View.
PT1945P 18 ► Side View ► T op View ► Front View.
Compatibility Modes Mode Resolution H-Frequency (KHz) V -Frequency (Hz) IBM VGA 720 x 400 31.47 70 IBM VGA 640 x 480 31.47 60 VESA VGA 640 x 480 37.86 72 VESA VGA 640 x 480 37.50 75 VESA SVGA 800 x 600 35.16 56 VESA SVGA 800 x 600 37.88 60 VESA SVGA 800 x 600 48.
T ouch Screen Driver Installation The PT1945R/PT1945S is available with both RS232 and USB connections. The touch driver is located at www .planar .com/support for these operating systems: W indows ® 7/8, VIST A, XP , 2000, ME, 98, NT 4.0, CE, XP Embedded, Linux 2.
PT1945P Optional Calibration T ool Install: Calibrating the touch screen in Windows 7/8: 1. T ap the Start button, Control Panel and then Hardware and Sound. 2. Under T ablet PC Settings, tap Calibrate the screen for pen or touch input. 3. On the Display tab, under Display options, tap Calibrate and then Y es to allow the program to make changes.
22.
PT1945R/PT1945S Install Instructions: If you are using a PC running Windows® 7/8, VIST A, XP , 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the display .
When changing the T ouch Interface (RS-232 or USB), please follow instructions below . 1. Uninstall the touch driver . 2. Re-start the computer . 3. Remove the original T ouch Interface (RS-232 or USB). 4. Connect the computer to the T ouch Interface (RS-232 or USB) that you would like to use.
PT1945P Driver Install Instructions: If you are using a PC running, Windows® 7/8, VIST A, XP , 2000, follow the instructions below: 1. Power on the PC. 2. Make sure that the USB cable is connected to the computer . 3. Visit www .planar .com/support. 4.
T echnical Support Cables and Accessories To fi nd cables and accessories for your Planar monitor , touch screen or other Planar products visit our online store at www .
Planar Systems, Inc. Customer Service 24x7 Online T echnical Support: http://www .planar .com/ support 1 195 NW Compton Drive Beaverton, OR 97006-1992 T el: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day , 7 days a week © 2013 Planar Systems, Inc.
デバイスPlanar PT1945Sの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Planar PT1945Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanar PT1945Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planar PT1945Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planar PT1945Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planar PT1945Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanar PT1945Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planar PT1945Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanar PT1945Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。