PlanarメーカーPT2245PWの使用説明書/サービス説明書
ページ先へ移動 of 25
PT2245PW T ouch Screen Monitor USER’S GUIDE www .planar .com.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright.
T able of Contents Usage Notice Precautions ................................................................................................................. 1 Introduction About PT2245PW Series ........................................................
Usage Notice ! W arning - T o prevent the risk of re or shock hazards, do not expose this product to rain or moisture. ! W arning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user ’s manual to maximize the life of your unit.
Introduction About PT2245PW Series The PT2245PW Series is a 21.5" at panel screen with an active matrix, thin-lm transistor (TFT) edge-lit LED LCD.
3 Package Overview Cable Cover Screw LCD Display Power Cord VGA Signal Cable USB Cable ( A to B) DVI-D Cable DC Power Supply Landing Strip User ’s Guide xxxxxxxxx / xxxxxxxxx xxxxxxxxx USER’S GUIDE www.
Installation Product Overview • Front V iew • Bottom V iew (Without Stand) 4 VGA USB DC IN DVI RJ -Type.
VESA Mount for Y our Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which denes a physical mounting interface for at panel monitors, and corresponding with the standards of at panel monitor mounting devices, such as wall and table arms.
Start Y our Installation Please follow these instructions so that you can hook up the cables to associated connectors. 1. Lay the display at on an even surface. 2. Move the stand into position as seen in the step 1 diagram. 3. Remove the cable cover as seen in the step 2 diagram.
7 Connecting the Display (Figure 8.1) T o setup this display , please refer to the following gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC plug to the power connector on the monitor and the other end into an electrical outlet (8.
8 (Figure 8.1) (Optional).
9 User Controls Side Panel Controls OSD Key Menu off status Menu on status Menu appear Menu disappear / return to main item Brightness Main item select up / Adjust up Contrast Main item select down / .
10 How to Use the OSD Menus Icon Key Name Menu Up Down Select Power 1. Press the “Menu” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the ve functions in the main menu. 2. Choose the adjustment items by pressing the “Select” button.
11 On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically . Left/Right Moving screen image horizontal position to left or right.
12 Appendix T roubleshooting If you are experiencing trouble with the display , refer to the following. If the problem persists, please contact your local dealer or our service center .
W arning Signal If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card. Below are the three kinds of W arning Signal. Please check the cable connections or contact your local dealer or our service center for more information.
Product Dimensions ► Side View ► Front View ► Top View 517.4 mm 313.3 mm 351.7 mm 249.6 mm 219.0 mm 212.0 mm 46.0 mm 14.
Rotate 15 ► Side View ► Front View ► Top View 313.3 mm 517.4 mm 553.7 mm 212.0 mm 46.0 mm 219.0 mm 249.6 mm.
Compatibility Modes Mode Resolution H-Frequency(khz) V -Frequency(hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple MacII 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA SVGA 800X600 35.16 56 VESA SVGA 800X600 37.88 60 VESA SVGA 800X600 48.
T ouch Screen Driver Installation The is available with USB connection. The touch driver is available at www .planar .com/sup- port for these operating systems: Windows® 7/8, VIST A, XP , 2000, CE, XP Embedded, Linux kernel 2.6.x (32 bit & 64 bit) , Apple® Mac OS.
18 PT2245PW Calibration Instruction: Calibrating the touch screen in Windows 7/8: 1. T ap the Start button, Control Panel and then Hardware and Sound. 2. Under T ablet PC Settings, tap Calibrate the screen for pen or touch input. 3. On the Display tab, under Display options, tap Calibrate and then Y es to allow the program to make changes.
19.
PT2245PW Install Instruction: If you are using a PC running, Windows® 7/8, VIST A, XP , 2000, follow the instructions below: 1. Power on the PC. 2. Make sure that the USB cable is connected to the computer . 3. Visit www .planar .com/support. 4. Follow the step-by-step instructions as shown on the pop-up windows.
T echnical Support Cables and Accessories T o nd cables and accessories for your Planar monitor , touch screen or other Planar products visit our online store at www .
Planar Systems, Inc. Customer Service 24x7 Online T echnical Support: http://www .planar .com/ support 1 195 NW Compton Drive Beaverton, OR 97006-1992 T el: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day , 7 days a week © 2013 Planar Systems, Inc.
デバイスPlanar PT2245PWの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Planar PT2245PWをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanar PT2245PWの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planar PT2245PWの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planar PT2245PWで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planar PT2245PWを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanar PT2245PWの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planar PT2245PWに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanar PT2245PWデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。