PlanarメーカーPX2210MWの使用説明書/サービス説明書
ページ先へ移動 of 25
PX2210MW.
1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com Customer Service Planar provides the following technical support services: Internet Support For support available 24/7 visit Planar's Online Technical Support at www.planar.com/support.
1.
2 The information contained in this document is subject to change without notice. This document contains proprietary informa tion that is protected by copyright.
3.
4 TABLE OF CONTENTS For Your Safety For Your Safety -----------------------------------------------------------5 General Notes Special notes on LCD monitors ----------------------------------------- 7.
5 FOR YOUR SAFETY Before operating the monitor, pleas e read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (F.
6 z Do not use the monitor near water, e.g. near a bathtub, w ashbow l, kitchen sink, laundry tub, sw imming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance.
7 GENERAL NOTES The following symptoms are normal w ith LCD monitor and do not indicate a problem. • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears.
8 BEFORE YOU OPERATE THE MONITOR • 2 2 ” ( 55.87 cm) TFT Color LCD Monitor • Crisp & Clear Display for Window s • Recommended Resolution: 16 8 0 X 1 05 0 @ 60Hz • Ergonomic Design wi th .
9 INSTALLATION INSTRUCTIONS Pow er Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allow s operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.
1 0 INSTALLATION INSTRUCTIONS (cont.) Connecting The Cables Figure 2 Connecting Cables 1. AC Power Cord 4 . 15-pin D-SUB Cable 3. DVI Cable Turn off your computer befor e performing the procedure below . 1. Connect the female end of the AC pow er cord to the AC-in port on the back of the monitor.
1 1 INSTALLATION INSTRUCTIONS (cont.) Tilt Adjustment For optimal viewing it is recommended to l ook at the full face of the monitor, then adjust the monitor's angl e to your ow n preference. Hold the stand so you do not toppl e the monitor w hen you change the monitor's angle.
1 2 OPERATING INSTRUCTIONS EXTERNAL CONTROLS Figure 4 - External Controls 1. -/ Volume Control 5. 2. +/ Volume Control Power Button 3. SELECT 4. 1<->2/RESET • Pow er Button: Press this button to turn the monitor ON or OFF. • SELECT : Activates OSD menu or confirms function.
1 3 OPERATING INSTRUCTIONS (cont.) • 1<->2/RESET : 1. When OSD menu is in active stat us, this button w ill act as EXIT-KEY (EXIT OSD menu) or go back to the previous menu.
1 4 OPERATING INSTRUCTIONS (cont.) How To Adjust A Setting 1. Press the SELECT -button to activate the OSD window (Figure 5). 2. Press + or - to navigate through the functions. Once the desired function is highlighted, press t he SELECT -button to activate it.
1 5 OPERATING INSTRUCTIONS (cont.) The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Contrast Contrast from Digital-register.
1 6 OPERATING INSTRUCTIONS (cont.) Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description H. Position Adjust the horizontal position of the OSD. V. Position Adjust the verticalposition of the OSD. OSD Setup OSD Timeout Adjust the OSD timeout.
1 7 TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Pow er Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if .
1 8 TECHNICAL SUPPORT (FAQ) (cont.) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal.
19 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 5 5.87 cm(2 2 ") Pixel pitch 0.2 82 mm( H )x 0.2 82 mm( V ) R,G,B Analog Interface Video Digital interface H-Frequency 3 1 KHz – 80 K Hz V-Frequency 5 6 -75Hz Display Colors 16.
2 0 APPENDIX (cont.) Switch • 1<->2/RESET • Volume • Volume • SELECT • Power Button External Controls: Functions • Contrast • Brightness • Focus • Clock • H.
2 1 APPENDIX (cont.) Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY(KHZ) VERTICAL FREQUENCY(HZ) DOS 720x400 31.469 70 DOS 640x350 31.469 70 IBM XGA 1024x768 57.515 72 VGA 640x480 35.000 67 SVGA 832x624 49.725 75 MAC XGA 1024x768 48.780 60 640x480 31.
2 2 APPENDIX (cont.) Connector Pin Assignment 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Video-Red 9. +5V 2. Video-Green 10. Detect Cable 3. Video-Blue 11. NC 4. NC 12. DDC-Serial data 5. Ground 13. H-sync 6.
Q41G 2201 935 1 A 1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
デバイスPlanar PX2210MWの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Planar PX2210MWをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanar PX2210MWの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planar PX2210MWの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planar PX2210MWで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planar PX2210MWを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanar PX2210MWの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planar PX2210MWに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanar PX2210MWデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。