Planetメーカー85M Powerline to Ethernet Bridge with 4-Port Switch PL-420の使用説明書/サービス説明書
ページ先へ移動 of 22
85M Powerline to Ethernet Bridge with 4-Port Switch PL-420 User Manual.
Copyright Copyright (C) 2006 PLANET Technology Corp. All rights reserved. The products and programs described in th is User’s Manual are licensed products of PLANET Technology, This User’s Manual .
CE mark Warning The is a class B device, In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Table of Content C HAPTER 1: I NTRODUCT ION ................................................................................. 5 O VERVIEW ..................................................................................... 5 F EATURES ...............
Chapter 1: Introduction Overview The Planet 85M Powerline to Ethernet Bridge with 4-Port Switch, PL-420, operates on the HomePlug Powerline Spec ification 1.
Specification Model PL-420 Standard HomePlug Powerli ne Specification 1.0.1 compliant IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX Ports Four RJ-45 ports Cabling Type Power cord Speed Up to 85Mbps Encryption 56-Bits DES encryption LED PWR, HP, LAN 1-4 Powerline Frequency Band 4.
• Standard home power line wiring • CD-ROM utility Front Panel LED definition LED Description PWR Steady on indicates when power on HP Steady on indicates when find out another HomePlug Flashing i.
Wire Diagram 8.
Chapter 2: Installation Overview The installation of 85M Powerline Ether net Switch will only take minutes. No need to set up long wires through out the house, just simply install the utility, and physically plug the power code into the device and wall outlet, then to connect RJ-45 to the computer.
Please click on ‘ Next ’ to continue the installation. On this screen you will be asked to input the User Name and Organization. It is not crucial to the device itself, so enter it as desired.
applied. For example: If the user wishes only he/she ca n use the utility with that particular account, then bubble in ‘ Only for me ’. For those without multiple accounts or wishes to allow all us ers to access the utility choose ‘ Anyone who uses this computer (all users) ’.
This section allows a user to go ‘ Back ’ or ‘ Install ’ the utility. In case if the user wishes to change the previous options then go ahead, click on ‘ Back ’ to change the settings. If not, continue and click the ‘ Install ’ button.
This screen shows that the installati on was completed successfully. Click on Finish to exit the wizard. 13.
Chapter 3: Configuration Overview The PL-420 uses 56-Bit DES encryption to block outside access. The key is set by using the Configuration Utility on the CD. By defaul t, the protection is enabled, however, it is recommended to change the default network password.
The Main tab shows the powerline units that are connected to the current computer and other power line devices on the home network, and it will also display Mac Address of each device.
The Main tab shows all the other power line units on your home network. It will represent them by MAC Address, and will also show the available bandwidth to each unit (Units farther away from another powerline device might have a lower Data Rate).
Setting Up Security on a Local Powerline device The Privacy tab will allow you to change the Netw ork Password to the unit that is currently connected to th is computer. This network password encrypts all data that is sent from this unit using 56-Bit data encryption standard (DES).
Setting Up Security on a Network Powerline device The Privacy Tab will allow users to use one primary computer to control the Network Passw ord of all units on the home network. You will have to go back to the Main Tab first then find the DEK (Device Encryption Key) Key located on the bottom of each device.
**Note** The DEK is unique for EACH Powerline device. To use this you will need to input the DEK for each unit. 19.
Appendix A: Troubleshooting Frequently Asked Questions 1. What’s the speed of the PL-420 operating over a standard home power line network? The PL-420 operates up to 85 Mbps band width over a standard home power line network. 2. What’s the Estimated Range of the PL-420? Approximately 300 meters in wall power lines (one household).
Run the HomePlug Configurat ion Utility, it will show your current speed and your signal strength. 9. One of the PL-420’s LED doesn’t light up after I plug the HomePlug directly into a wall outlet? Test that wall outlet with other electric devic es first, make sure that wall outlet is working properly.
14. How many HomePlug devices that I can install into one Local Area Network? It is recommended install up to 16 HomePlug devices in one same password powerline network.
デバイスPlanet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Planet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanet 85M Powerline to Ethernet Bridge with 4-Port Switch PL-420デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
