Planet TechnologyメーカーFGSW-4840Sの使用説明書/サービス説明書
ページ先へ移動 of 39
48-10/100Mbps + 4G Ethernet Web Smart Switch FGSW-4840S User’s Manual.
2 Trademarks Copyright PLANET Technology Corp. 2004. Contents subject to revisi on w ithout prior notice. PLANET is a registered trademark of PLANET Technology Corp.
3 TABLE OF CONTENTS 1. INTRODUCTION ............................................................................................. ……………………1 1.1 P ACKAGE C ONTENTS ........................................................................
1 1. INTRODUCTION 1.1 Package Contents Check the contents of your packag e for follow ing p arts: ● Web Smart Gigabit Ethernet Switch x1 ● CD-ROM user's manual x1 ● Quick installation guide.
2 Support CSMA/CD protocol 100~240VAC, 50~60Hz universal Power input FCC, CE class A compliant 1.4 Product Specifications Model FGSW-4840S Hardware Specification 10/100Base-TX ports 48 10/100/1000Mbps ports 2 SFP-Mini-GBIC interfaces 2 Switch architecture Store-and-Forward Switch Fabric 17.
3 2. INSTALLATION This section describes the f unctionalities of FGSW -4840S’s co mponents and guides how to insta ll it on the desktop or shelf. Basic knowledge of netw orking is assumed.
4 Per 1000Base-T port LED Color Function LNK/ACT Green Lit: indicate the link through that port is successfully established. Blink: indicate that the switch is active ly sending or receiving data over that port. SPEED Green/orange Green: indicate that the port is operating at 1000Mbps.
5 Step5 : Supply pow er to the Switch. A. Connect one end of the power cable to the FGSW -4840S. B. Connect the power plug of the pow er cable to a standard w all outlet. When the FGSW-4840S receives power, the Power LED should remain solid Green. 2.2.
6 3. CONFIGURATION Unlike the unmanaged switch (Dumb sw itch), FGSW-4840S performs series smart func tions that make the Sw itch operate more effectively.
7 Figure 3-2 Web Switch Utility install process Figure 3-3 Web Switch Utility install process.
8 Figure 3-4 Web Switch Utility install process Figure 3-5 Web Switch Utility install process.
9 Figure 3-6 Web Switch Utility install process Figure 3-7 Web Switch Utility install completed 4. After install completed, choose Program Files -> PLA NET Web Switch and execute the Web Swit ch utility.
10 Figure 3-8 Web Switch Utility main screen The Web Switch Utility w as divided into four parts, Toolbar function , Discovery List, Monitor List, Device Setting, please refer to the below secti on for the details instruction. 3.1.1.1 Toolbar function The toolbar in the Web Switch Utility provide four main tabs.
11 Figure 3-9 Web Sw itch Utility’s File screen 3.1.1.1.2 View In the “View TAB” , it provides view log and clear log function, this function w ill help user to view the trap message. The detail explanation of each it em is shown as below : View Log : to display the events of the FGSW-4840S.
12 3.1.1.1.4 Help In the “Help TA B” , it provides “A bout” function, it display the versi on of the Web Switch Utility . Figure 3-12 Web Switch Utility’s Help screen 3.1.1.2 Discovery List This function allows user to list the FGSW -4840S in the entire net work.
13 The Discovery List contains nine items: MA C A ddress : display the Sw itch MAC Address. IP A ddress: display the current IP address of the Sw itch. Protocol ve rsion: display the version of the Utility protocol. Product Name: display the Sw itch model name.
14 Protocol ve rsion: display the version of the Utility protocol. Product Name: display the Sw itch model name. System Name: display the appointed Sw itch sy stem name. Location: display w here the Sw itch is located. Trap IP: display the IP address w here the Trap to be sent.
15 Figure 3-16 T rap information screen Note : In order to receive Trap information, th e FGSW-4840S must configured with T rap IP and Trap Events in Web interface. Please refer to chapter 3.1.2.9 T rap fo r detail information. A dd Item: To add a device to the Monitor List manually, enter the IP Address of t he device that w ant to monitor.
16 Firmw are Upgrad e: this function allows new firmw are upgrade of FGSW-4840S. The screen in Figure 3-19 appears. Figure 3-19 Firmware Upgrade screen Firmw are upgrade Procedure Step 1: Click “Bro.
17 Figure 3-21 Firmware Upgrade process screen Step 3: After firmware upgrade completed, the Sw itch will reboot automatically. T hen the follow ing screen in Figure 3-22 & 3-23 appears. Figure 3-22 Firmware Upgrade completed screen Figure 3-23 Firmware Upgrade successful screen After Switch pow er on completed.
18 3.1.2 Configure the FGSW-4840S The FGSW-4840S Web Smart Gigabit Ethernet Switch provide Web interface for Swit ch smart function c onfiguration. The FGSW-4840S can be configured through the Web Browser. A network admin istrator can manage and monitor the FGSW-4840S from the local LAN.
19 Figure 3-25 Web Main screen 3.1.2.3 Port This function allows displaying eac h port’s status. The Link Status in the screen display s t he current connection speed and duplex mode; else this function will show “Down” when the port is disconnected.
20 Figure 3-27 Per Port Setting screen The options and descriptions of Port Settings shown as below : Speed: this function provides six modes—100M Full, 100M Half, 10M Full, 10M Half, Auto and Disable. Note : When set each port to run at 100M Full, 100M Ha lf, 10M Full, and 10M Half-speed modes.
21 Figure 3-28 VLAN Setting screen To add a VLAN group, please press “Add Group” button, the new VLAN configuration screen will pop out, you can fill in the description in order to describe this VLAN Group, check on the port to be a member to this VLAN Group.
22 Figure 3-30 Edit existence VLAN Setting screen Figure 3-31 Edit existence VLAN Setting screen After edit completed. Press “A pply” button to execute the setting.
23 Figure 3-32 Edit existence VLAN Setting screen Delete the existence VLAN group. Press “Delete Group” button then the follow ing screen appears. Figure 3-33 Delete existence VLAN group screen Press “A pply” button to execute the setting. The following screen in Figure 3-34 appears.
24 Figure 3-34 Delete existence VLAN group screen Note : The FGSW-4840S supports 26 port-based VLAN groups. Due to the hardware restriction. The por t-based VLAN function cannot across between port 1-24 and port 25-52.
25 Selection 4(port 33, 34, 35, 36, 37, 38, 39, 40) Group 6: Selection 1(Disable) Selection 2(port 41, 42) Selection 3(port 41, 42, 43, 44) Selection 4(port 41, 42, 43, 44, 45, 46, 47, 48) Group 7: Selection 1(Disable) Selection 2(port 49, 50) After setup completed.
26 3.1.2.6 St atus Click on the “Status” to present the Switch status on th is screen, it display the Sw itch St atus, Port Status, VLAN Status, Trunk Status. Press “Refresh” to renew the posted informa tion. The Status screen in Figure 3-36 appears.
27 Figure 3-38 Per port Statistics screen 3.1.2.8 System The System Setting includes the System name, Location name, Login Timeout, IP Address, Subnet Mask and Gateway . Through the Web Switch Utility, you can easily recognize the device by using t he System Name and the Location Name.
28 3.1.2.9 Trap The Trap function enables the Switch to monitor the T rap thr ough the Web Switch Utility, set the Trap IP Address of the manager workstation w here the trap to be sent. After setup completed. Press “Apply ” button to execute the setting.
29 3.1.2.10 Passw ord Setting This function provides administrator to secure FGSW-4840S. After setup completed. Press “Apply” button to execute the setting. The screen in Figure 3-41 appears. Figure 3-41 Password Setting screen Note : Up to 20 characters is allowed for the p assword.
30 Press the “Backup” button to save the current c onfiguration in manager workstat ion. The following screens in Figure 3-43& 3-44 & 3-45 appear.
31 Figure 3-45 Backup Setting screen To restore a current configurati on file to the FGSW-4840S, please specify the backup file and press “Restore” button to continue, after restore completed, the FGSW-4840S will reboot for the prev ious configuration.
32 Figure 3-48 Reset Setting screen 3.1.2.13 Logout Press this function; the web interface w ill go back to login screen. The screen in Figure 3-49 appears.
33 4. SWITCH OPERATION 4.1 Address Table The Switch is implemented w ith an address t able. This address table com posed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc.
34 5.TROUBLESHOOTING This chapter contains information to hel p you solve problems. If the Switch is not functioning properly, make sure the Ethernet Switch w as set up according to instructions in this manual. The Link LED is not lit Solution: Check the cable connection and its quality.
35 APPENDIX A A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_DC.
36 Figure A -1: Straight-Through and Crossov er Cable Please make sure your connected cables are w ith same pin assignment and color as abov e picture before deploy ing the cables into your netw ork.
デバイスPlanet Technology FGSW-4840Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Planet Technology FGSW-4840Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanet Technology FGSW-4840Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planet Technology FGSW-4840Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planet Technology FGSW-4840Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planet Technology FGSW-4840Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanet Technology FGSW-4840Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planet Technology FGSW-4840Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanet Technology FGSW-4840Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
