Planet TechnologyメーカーFSD-1601SCの使用説明書/サービス説明書
ページ先へ移動 of 23
.
Trademarks Copyrigh t PLAN ET T echnolog y Corp. 2004 PLANET i s a regi stered tr adema rk of PL ANET T echnol ogy Corp . All ot her tr adema rks be long t o their respe ctive owners. Conte nts in this docu- ment are subject to revis ion with out prior notice.
1 T able of Contents Chap ter 1 G ener al Intr oduc tion 1 1.1 Chec klist 1 1.2 Intr oduct ion 1 1.3 Fe atur es 2 Chap ter 2 H ardw are Des crip tion 3 2.1 Fron t P anel 3 2.1. 1 FS D-800 /FSD-801 3 2.1. 2 FS D-160 0/FSD-16 01 4 2.2 Re ar P anel 5 2.3 Hard ware Ins tall atio n 7 Chap ter 3 C onfi gur atio n an d A ppli cati on 8 3.
1 Chapter 1 General Introduction 1.1 Checklist Check the contents of your package for following parts: • The F ast Eth erne t S witch • User’ s Manu al • Po wer Cord If any of these pieces are.
2 3 1.3 Features • 8/16 -port 10/100b ase- TX Au to-N egoti ation Et hern et S witches • One optio nal 100B ase- FX f iber port for ext endi ng u p to 2km • Comp lies with the IEEE8 02.
2 3 Chapter 2 Hard ware Description This section describes the hardware features of the Switch. For easier management and control of the Switch, familiarize y ourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators.
4 5 FDX/ COL Amber Lit: Full duplex operation Unlit: Half duplex operation Blink: indicates data collisions on the respective Ethernet segment of this port. Whenever a collision is detected, the respective COL indicator will briefly blink. This is normal when the network is busy .
4 5 LED indicators Printing Color Description Power (PWR) Green This indicator lights green when the Switch is receiving power; otherwise, it is off . LNK/ ACT Green This indicator green when the port.
6 7 DIP Switch (Smart function for FSD-1600/1601) DIP Function Description 1 TP / FX Selection ON: Enable FX OFF: Enable TP 2 Fiber Full/Half duplex Switch ON: Enable Fiber Full Duplex OFF: Enable Fib.
6 7 NOTE: 1. F or fibe r-o ptic connec tion , pleas e check the oppo site end is us- ing the same tr ansm it m ode befo re ma ke the conn ectio n. 2. Po rt#16 of the switch is shared with 100Bas e-FX port. Make sure eit her F iber-op tic or t wiste d pa ir p ort is b eing conn ecte d.
8 9 Chapter 3 Configuration and Application This chapter shows you how the Switch works, and how to install the Switch and also to congure the smart functions provided in the 16-port model. 3.1 The Switch Operation Address T able The Switch is implemented with an address table.
8 9 domain, reducing the overall load on the network. The Switch performs “Store-and-forward” therefore, no error packets occur . More reliably , it reduces the re-transmission rate. No pack et loss will occur . Auto-Negotiation The STP ports on the Switch have built -in "Auto-Negotiation.
10 1 1 3.2.2 Port-based VLAN Related DIP: 3, 4 Default meaning: No VLAN setting. VLAN can be used to separate ports into different groups in the same switch.
10 1 1 DIP 10: T urns on for VLAN tag priority QoS. NOTE: The connected end-nodes (PCs, Routers) should also support VLAN priority or T oS priority . Normally , these functions could turn off by default. Check the user ’s guide of your networked device for this capability .
12 13 Figure 3-1 10/100Mbps File server to Switch Connection 3.3.2 Connect to 100Base-FX Switch/Device (Model: FSD-801/1601) Plug the pair the ber-cable to the Switch’ s ber-optic port, secure the ber-optic connector . Connect to other end to the ber-optic port of the device like repeater hub, switch or workstations.
12 13 3.3.3 Set up the workgroup and uplink to the backbone (Model: FSD- 1600/1601) Figure 3-3 Connection with VLAN enable T urn on the DIP 4, the FSD-1600 soon separate the fourteen ports (P ort 1 to.
14 15 Chapter 4 T roubleshooting This chapter contains information to help you solve problems. If the Switch is not functioning properly , make sure the Switch was set up according to instructions in this manual.
14 15 Appendix A Specifications General (Ethernet) Standards: IEEE 802.3 10Base- T EthernetIEEE 802.3u 100 Base- TX and 100Base-FX F ast EthernetIEEE 802.
16 17 EMI FCC Class A, CE Mark Class A Performance T ransmission Method Store-and-forward Filtering Address T able 1/8K entries Packet Filtering/ Forwarding R ate 14,880pps per port (for 10Mbps) 148,8.
16 17 Appendix B RJ-45 Pin Specification When connecting your FSD-series 10/100Mbps Ethernet Switch to another switch, a bridge or a hub, a modied crossover cable is not necessary . Each port of the Switch is auto-MDI detection. That means you can direct connect the Switch to any Ethernet devices with a Category 5, UTP straight wire.
18 This pag e is int entionall y left b lank.
18.
Part No.: 2010-000004-003.
デバイスPlanet Technology FSD-1601SCの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Planet Technology FSD-1601SCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanet Technology FSD-1601SCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planet Technology FSD-1601SCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planet Technology FSD-1601SCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planet Technology FSD-1601SCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanet Technology FSD-1601SCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planet Technology FSD-1601SCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanet Technology FSD-1601SCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
