Planet TechnologyメーカーFSD-504PEの使用説明書/サービス説明書
ページ先へ移動 of 20
5-Port 10/100Mbps Fast Ethernet Switch with 802.3af splitter built-in FSD-504PE User ’ s Manual.
Trademarks Copyright © PLANET Technology Corp. 2005. Contents subject to revision without prior notice. PLANET is a registered trademar k of PLANET Technology Corp.
Table of Contents T able of Contents ............................................................................................................................. 3 ABOUT THIS GUIDE .....................................................................
ABOUT THIS GUIDE Thank you for purchasing t he FSD-504PE, 5-Port 10/100Mbp s Fast Ethernet Switch with 802.3af splitter built-in. This device integrates 100M bps Fa st Ethernet and 10Mbp s Ethernet network capabilities in a highly flexible de skto p p ackage and also offers d ual power system , DC power and IEEE802.
Chapter 1 INTRODUCTION This chapter describes the features of the Swit ch a nd some background information about Fast Ethernet switching technol ogy . Fast Ethernet Technology The growing import an ce of LANs and the incre asi ng complexity of desktop com puting applications are fueling the need for high perfo rman ce networks.
collision domains, ma king it possible to exp and your Fast Ethernet netwo rk beyond the 205-meter network diameter limit for 100Ba se-TX network s. Switches suppo rting both traditional 10Mbps Ethernet and 100Mbp s Fast Ethernet are also ideal for bridging between the existing 10Mbp s networks and the new 100 Mbps networks.
10Mbps or 100Mbps workgroups. With the highest bandwidth 200Mbps (100Mbps full-duplex mode), any port can provide workst ations with a congestion-free data pipe for simultaneous access to the server. The Switch is expandable by cascading two or mo re switches together.
.
Chapter 2 UNPACKING AND SETUP This chapter provides un p acking and setup information for the Switch. Unpacking Open the shipping cartons of the Switch and care fully unpacks it s contents.
Chapter 3 IDENTIFYING EXTERNAL COMPONENTS This section identifies all the major external co mponent s of the Switch. Both the front and rear panels are shown follo wed by a description of each panel’s feature. Panel The figures below show the p a nels of the swit ch.
DC Power Jack: Power is supplied through an extern al AC po wer ad a pter. Check t he techni cal specification section for informatio n abo ut the AC power input voltage. Since the switch does not incl ude a power swit ch, plug ging its power adapter into a power outlet will immediately power it on.
Chapter 4 CONNECTING THE SWITCH This chapter describe s how to connect t he Switch to your Fast Ethernet netwo rk. PC to Switch A PC can be connected to the Switch via a two-pair Categ ory 3, 4, 5 UTP/ STP straight cable. The PC (equipped with a RJ-45 10/100Mb ps phone jack) sho uld be connected to any of the 5 numbered port.
Powered from POE hub / switch Port#1 of the Switch support IEEE802.3af power ov er Ethernet, you can direct connect the Switch to the 802.3af in-line power devices li ke 802.3af POE hub, Ethernet Switch es that with 802.3af POE Ethernet port. A Category 5 UTP cable with 4-pair wire is re quired from POE hub to your FSD-504PE.
will require four-pair Cat 5/ 5e UTP/STP cable. When using straight or crossover cabl e, this is done from the any (MDI/MDIX) port of the Switch (Switch A) to any of the 10Mbp s or 100Mbp s (MDI-X ) port of the other switch (switch B) or other devices.
Chapter 5 TECHNICAL SPECIFICATIONS Model FSD-504PE Standards IEEE802.3 10B ase-T Ethernet IEEE802.3u 100Base-TX Fast Ethernet IEEE802.3af Power over Ethernet Protocol CSMA/CD Data Transfer Rate Ethern.
APPENDIX A RJ-45 PIN SPECIFICATION When connecting your FS D-series 10/100Mbp s Et hernet Switch to another swi tch, a bridge or a hub, a straight or cro ssover cable is necessary . Each port of the Switch support s auto-MDI/MDI-X detection. That means you can di rectly connect t he S witch to any Ethernet devices without makin g a crossover cable.
There are 8 wires on a st andard UTP/STP cable and each wire is color-coded. The following shows the pin allocation an d colo r of stra ight cable and crossover cable connection: Figure A-1: S traight.
APPENDIX B SWITCH OPERATION Address Table The Switch is implemented with an address table. This address table compo sed of many entries. Each entry is used to store the address info rmation of some node in network, including MAC address, port no, etc.
Due to the learning function of the Ethernet switch, the source addre ss and corresp onding port number of each incomi ng and outgoing p acket are st ored in a routing table. This informatio n is subsequently used to filter p ackets who se dest ination addres s is on the same segment as the source address.
Appendix C Troubleshooting 1. Power LED does not turns on? Ans: The Switch supports two power so urces, 12VDC and 802.3af, please check which kind of power system deployed. a) Powered from POE: please check with netwo rk administrator if the POE injector device is complied with 802.
デバイスPlanet Technology FSD-504PEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Planet Technology FSD-504PEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanet Technology FSD-504PEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planet Technology FSD-504PEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planet Technology FSD-504PEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planet Technology FSD-504PEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanet Technology FSD-504PEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planet Technology FSD-504PEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanet Technology FSD-504PEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
