Polycomメーカー1725-36071-001の使用説明書/サービス説明書
ページ先へ移動 of 22
January 2008 Edition 1725-36071-001 Version C VIEW Certified Configuration Guide Siemens HiPath Wireless System with 2610, 2620 APs.
Configuration Guide PN: 1725-36071-001_C.d oc 2 Trademark Information Polycom® and t he logo design s SpectraLink® LinkPlus Link NetLink SVP Are trademarks and registe red trademarks of Polycom, Inc. in the Un ited States of Am erica and various c ountries.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 3 Introduction SpectraLink's Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is designed to ensure interoperability and high performance between SpectraLink 8000 Wireless Telephones and WLAN infrastructure products.
Configuration Guide PN: 1725-36071-001_C.d oc 4 Network Topology The following topology was tested during VIEW Certification. It is important to note that these do not necessarily represent all "certified" configurations. The access points were powered through a mid-span POE adaptor.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 5 Installing Software & Configuration 1. If software upgrades are requ ired, contact Si emens Customer Support for the latest version of software and instructions.
Configuration Guide PN: 1725-36071-001_C.d oc 6 Initial Setup 1. The following instructions are for configuring a wireless controller and a number of access points with no prior configuration.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 7 Controller Setup The setup steps described below refer to the network topology diagram shown in this document. Make sure all the access points are disconnected from the system if configuring the system for the first time.
Configuration Guide PN: 1725-36071-001_C.d oc 8.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 9 Assigning routing protocols to a wireless controller 1. In the Wireless Controller screen, click Routing Protocols in the navigation pane. 2. Enter 0.0.0.0 for the Des tination Address and 0.
Configuration Guide PN: 1725-36071-001_C.d oc 10 AP registration 1. Click the Wireless APs button. 2. Click AP registration in the navigation pane. 3. Enter all information for your AP s (see screen shot below). Make sure the setting for Security Mode is selected to Allow all Wireless APs to Connect.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 11 AP maintenance 1. In the Wireless APs screen, click AP Maintenance in the navigation pane. 2. Select the proper image file in the AP Images box and click the Set as default button.
Configuration Guide PN: 1725-36071-001_C.d oc 12 Setting up SSID, Security and QOS 1. Click the VNS Configuration button. 2. Click the Topology tab. 3. Assign a subnet for clients for a specific SSID . 4. Under DHCP Settings : a. Enter the appropriate address for the Gateway b.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 13.
Configuration Guide PN: 1725-36071-001_C.d oc 14 Filtering 1. In the VNS Configuration screen, click the Filtering tab. 2. Select Default from the Filter ID drop-down list. a. Select all three options - In, Out and Allow. b. Leave the IP:Port as *.*.*.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 15 Multicast configuration 1. In the VNS Configuration screen, click the Multicast tab. 2. Select the Enable Multicast Support check box. 3. From the Defined groups drop-down list, select or enter Spectralink SVP (224.
Configuration Guide PN: 1725-36071-001_C.d oc 16 Security 1. In the VNS Configuration screen, click the Privacy tab. 2. For WPA2 AES-CCKM, click the WPA-PSK option, clear the WPA v.1 check box, then select the WPA v.2 check box. 3. For WPA TKIP, click the WPA-PSK option, clear the WPA v.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 1 7 Quality of service 1. In the VNS Configuration screen, click the Policy tab. 2. From the Quality of Service drop-down list, select Voice VN S w/o WMM ; this is required for SpectraLink phones.
Configuration Guide PN: 1725-36071-001_C.d oc 18 Connecting access points to the controller 1. Click the Reports button. 2. Make sure the controller is configured to accept new APs (this is selected by default). 3. Physically connect the access points to the syste m one at a time.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 19 Wireless APs address assignment 1. After all the APs have been connected and discovered by the controller, click Wireless APs tab. 2. Click the Static Configuration tab. 3.
Configuration Guide PN: 1725-36071-001_C.d oc 20 For each AP, follow the steps in the following sections: AP properties 1. In the Wireless APs screen, click the AP Properties tab. Select an AP to configure. Here you can assign a meaningful name to each AP.
Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.d oc 21 4. For Enable Radios , select the 802.11b check box. 5. Under Radio Settings : a. Select the appropriate Channel and Tx Power Level. (Note: DRM values will override this setting, if enabled).
Configuration Guide PN: 1725-36071-001_C.d oc 22 Enable the radio 1. Click the VNS Configuration button. 2. Click the Topology tab. 3. Enable each AP’s b/g radio for each SSID. 4. Set No. of Retries f or Voice VO to adaptive (multi-rate) and No. of Retries for Turbo Voice TVO to 2 .
デバイスPolycom 1725-36071-001の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Polycom 1725-36071-001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPolycom 1725-36071-001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Polycom 1725-36071-001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Polycom 1725-36071-001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Polycom 1725-36071-001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPolycom 1725-36071-001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Polycom 1725-36071-001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPolycom 1725-36071-001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
