PosiflexメーカーLS-1000Uの使用説明書/サービス説明書
ページ先へ移動 of 22
FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications.
FUNDAMENTAL INFORMA TION MODEL NAME : LS - 1000 CONTENT ( Besides this guide) : Fig . 1 Box content besides this g uide INSTALLATION GUIDES 1. Install the USB or RS232 interface cable onto the scanner by inserting the 8 pin RJ45 type modular plug ( Fig.
Description Function Scan Window Reads barcodes Object Detector Trigger and wake up scanner automatically when present ed with barcode in its range Beeper Hole Fo r beep tone indication USING THE SCANNER SCANNER INTRODUCTION Features The scanner unit is a compact and space - saving hands - free omni - directional laser scanner .
Wake up scanner When the scanner enters the sleep mode, pressing this switch can wake the scanner up. The sleep mode feature can be programmed using the menu labels from the Programming Guide. NO TE: The default time - out value is set to 10 minutes after laser sl e p t , 30 minutes after motor slep t .
SCANNER SETUP (PROGRAMMING) In most of the cases no setup is required. The defaul t setup of the scanner makes the scanner able to detect automatically the most commonly applied bar code types as tabulated above and send the data to the host system as if they are read from an USB or RS232 keyboard .
Cover unwanted codes with your hand and present the desired codes, one by one, to the scanner, the scanner beeps once as it accepts each code. When done, again present the < Enter/Exit programming mode > barcode. The scanner beeps twice, once long and once short, and the LED returns to blue.
SCANNER OPERATION Operating the Scanner The scanner read s barcodes in omni - directional scan mode as regular practice. It can also operate in single - line mode for a better aiming on a specific barcode that is printed on a surface with more than one barcode printed closely.
Sleep Mode After the scanner has been inactive for a period of time, the laser automatically turns off; then the motor will turn off and the scanner will enter the “ Sleep Mode ” , the blue status LED keeps blink ing as indication. To wake up the scanner, simply present an object close to the scan window, or press the function button.
Beeper Indications A beeper gives audible feedback on scanner operation. Beeps Indication One bee p A barcode has been successfully decoded. Four beeps in series This indicates the scanner passed the power on self - test and is operating properly. Two beeps: low - high The scanner has entered programming mode.
Page 10 make sure that the scanner is installed as instructed in this manual and that all cables are properly connected. If the problem remains, contact your dealer. Problem Diagnostic Tips The scanner window is dirty. Clean the scanner window as described in the Maintenance section.
The software running on the POS system does not support the data format of the barcode label. Enter/Exit Programming Mode Note: Scan t h is code to enter and exit programming mode. A slightly enlarged image of this code is also printed on the last page of this section for ease of application .
RESET Note: The reading of the “RESET” label turns all the parameters back to default values but leaving the interface mode unchanged. It is suggested to scan also the “ Return to USB default ” or “ Return to RS232 default ” label after this for LS - 1000 scanners.
Message Terminator - Enter Message Terminator - H.tab Message terminator - None International Keyboard (ALT method) Page 13.
Return to customer default Note: The reading of the label will recover all parameter back to customer default . Codabar Enable Save as customer default Codabar Disable Page 14.
Full ASCII COD E 39 Disable Code 39 Enable Code 39 Disable Full ASCII CODE39 Enable Page 15.
UPC/EAN/JAN Disable UPC/EAN/JAN Enable ITF 2 OF 5 Disable ITF 2 of 5 Enable Page 16.
UPC/EAN ADD ON OFF ADD ON 5 only ADD ON 2 only ADD ON 2 or 5 Page 17.
EAN/UPC +Add on (none mandatory) Force UPC - A to EAN - 13 format enable EAN/UPC + Add on (mandatory) Force UPC - A to EAN - 13 format disable Page 18.
EAN - 13 Convert to ISBN/ISSN Enable EAN - 13 Convert to ISBN/ISSN Disable EAN - 128 Enable EAN - 128 Disable Page 19.
Code 128 Enable Code 128 Disable Code 93 Enable Code 93 Disable Page 20.
Chinese Post Code Enable Chinese Pos t Code Disable Code 32 (Italian Pharmacy Code) Enable Code 32 (Italian Pharmacy Code) Disable Page 21.
MSI enable MSI Disable Enter/Exit Programming Mode Page 22.
デバイスPosiflex LS-1000Uの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Posiflex LS-1000Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPosiflex LS-1000Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Posiflex LS-1000Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Posiflex LS-1000Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Posiflex LS-1000Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPosiflex LS-1000Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Posiflex LS-1000Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPosiflex LS-1000Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。