PrecorメーカーS3.25の使用説明書/サービス説明書
ページ先へ移動 of 20
Assembly Instructions S3.25 Leg Press Option.
S3.25 Leg Press Option Assembly Instructions page 2 IMPOR T ANT SAFETY INSTRUCTIONS Impor tant Safety Instructions Impor tant Safety Instructions Before beginning any fitness program, you should obtain a complete physical examination from your physician.
S3.25 Leg Press Option Assembly Instructions page 3 T able of Contents T able of Contents Important Safety Instructions ............................................................... 2 Personal Safety Duri ng Assembly ................................
S3.25 Leg Press Option Assembly Instructions page 4 1 Before Y ou Begin Before Y ou Begin Thank you for purchasing the Leg Press Option for your Precor equipment. This option will add a new dimension to your strength-training regimen. For proper installation, please read this guide thoroughly and follow the assembly instructions.
S3.25 Leg Press Option Assembly Instructions page 5 2 Preparations Preparations CAUTION: T o set up this equipment, you will need assistance. Do not attempt assembly by yourself.
S3.25 Leg Press Option Assembly Instructions page 6 1 2 3 4 5 6 3 Assembly Instructions Assembly Instructions Assembly of the Leg Press Option takes professional installers about 1 hour to complete. If this is the first time you have assembled this type of equipment, plan on significantly more time.
S3.25 Leg Press Option Assembly Instructions page 7 1 2 3 4 5 6 1. Remove the Shroud Important: For ease of assembly , the fasteners and hardware for each step are labeled and packaged in separate bags. Note: If you are assembling the Leg Press Option along with your S3.
S3.25 Leg Press Option Assembly Instructions page 8 1 2 3 4 5 6 2 . Attach the C r oss Brace t o t h e S3.25 Note: If you are assembling the Leg Press Option along with the S3.25, you should complete Step 10 in the S3.25 Assembly and Maintenance Guide before attaching the Cross Brace.
S3.25 Leg Press Option Assembly Instructions page 9 1 2 3 4 5 6 3. Assemble the Frame A. With someone helping you, lift the Seat Frame upright. Have your assistant hold it in place while you attach the Cross Brace in the next step.
S3.25 Leg Press Option Assembly Instructions page 10 1 2 3 4 5 6 D . Assemble the Footrest by resting the Pivot Arm on the Rubber Bumper . Make sure that the red arrow on the back of the Footrest points toward the ceiling.
S3.25 Leg Press Option Assembly Instructions page 11 1 2 3 4 5 6 4. Assemble the Seat Pads A. Attach one of the Seat Pads to the Seat Bracket Support using two 1¼-inch bolts two washers Wrench tighten. B . Lift the Pop Pin and slide the Seat Pad out of the way to assemble the other Seat Pad.
S3.25 Leg Press Option Assembly Instructions page 12 1 2 3 4 5 6 Step 5. Route the Cable 5. Route the Cable As you route the Cable through the pulleys on the Leg Press Option, wrench tighten the fasteners on each pulley as you go. Make sure that the Cable slides freely along the pulley (and beneath the cable retainer).
S3.25 Leg Press Option Assembly Instructions page 13 1 2 3 4 5 6 Step 6. Assemble the Cable and Pulleys 3½" Pulley A 1 - 2" bolt 2 - washers 1 - locknut Attach this end to the Cable T ree C.
S3.25 Leg Press Option Assembly Instructions page 14 1 2 3 4 5 6 C . Reattach the end of the original Surgical T ube from the Cable T re e to its prior location and place the new Sur gic al Tube that .
S3.25 Leg Press Option Assembly Instructions page 15 1 2 3 4 5 6 7. Replace the Shroud A. Pick up the Shroud and fasteners from the location where you left them in Step 4B. B . Replace the Shroud by realigning the mounting holes and inserting six 2¾-inch bolts six washers six locknuts Wrench tighten.
S3.25 Leg Press Option Assembly Instructions page 16 1 2 3 4 5 6 4 Adjustments Adjustments B A T op Cap Weight C Chest Press Arms Weight Pin T op Cap Weight T op Weight After the Leg Press Option is assembled, you should check the Cables for proper tension.
S3.25 Leg Press Option Assembly Instructions page 17 1 2 3 4 5 6 B Rotate the Cam Washer T op Cap Weight Weight Pin A T op Cap Weight C T op Weight Weight then further adjustments are needed. Continue with steps 2 and 3. 2. Rotate the Cam W asher If the T op Cap Weight does not rest on the T op Weight, you must make further adjustments.
S3.25 Leg Press Option Assembly Instructions page 18 1 2 3 4 5 6 A B Adjust the Rubber Bumper Push the Pivot Arm up to adjust the Rubber Bumper Rubber Bumper Locknut Bracket C Weight Pin 3. Adjust the Rubber Bumper on the Leg Press Option If the T op Cap Weight still does not rest on the T op Weight, you can make one final adjustment.
Effective 01 August 2001 P/N 36287-108 Residential Equipment Limited Warranty Precor Incorporated warrants that all new Precor products are free of manufacturing defects in workmanship and materials. Parts repaired or replaced under the terms of this warranty will be warranted for the remainder of the original warranty period only .
Precor Incorporated 20031 142nd Avenue NE P .O. Box 7202 Woodinville, W A USA 98072-4002 PLACE ST AMP HERE W arranty Registration Card Please fill out the W arranty Registration and mail it to Precor .
デバイスPrecor S3.25の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Precor S3.25をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPrecor S3.25の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Precor S3.25の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Precor S3.25で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Precor S3.25を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPrecor S3.25の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Precor S3.25に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPrecor S3.25デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。