Pride MobilityメーカーJet10Ultraの使用説明書/サービス説明書
ページ先へ移動 of 44
Pride Exeter , P A 1-800-800-8586 St. Catherines, ON 1-888-570-1113.
2 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 SAFETY GUIDELINES Copyright © 2004 Pride Mobility Products Corp. INFMANU2731 The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important information.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 3 I. INTRODUCTION ................................................................................................................................. 4 II. SAFETY ..........................................
4 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 I. INTRODUCTION SAFETY WELCOME to Pride Mobility Products Corporation (Pride). The power chair you have purchased combines state-of- the-art components with safety , comfort, and styling in mind.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 5 I. INTRODUCTION PRIDE OWNERS CLUB As an owner of a Pride product, you are invited to register your product's warranty and enroll in the Pride Owners Club. Y ou may do so by filling out and returning your enclosed product registration card or by visiting Pride's web site at www .
6 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 II. SAFETY Cor r osiv e chemicals contained in batter y . Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive conditions. This product has been tested and passed at an immunity level of 20 V/m.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 7 II. SAFETY Do not remove anti-tip wheels. Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while operating. Av oid exposure to rain, snow , ice, salt, or standing water whenev er possible.
8 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 II. SAFETY SAFETY MAND A TOR Y! Do not operate your new power chair for the first time without completely reading and understanding this owners manual. Y our power chair is a state-of-the-art life-enhancement device designed to increase mobility .
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 9 II. SAFETY NOTE: If you discover a problem, contact your authorized Pride Provider for assistance. Weight Limitations Y our power chair is rated for a maximum weight capacity . Please refer to the specifications table for this limit.
1 0 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 II. SAFETY Figure 1. Maximum Safe Slope (Ascending and Descending) WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the incline. Drive your power chair straight up the incline.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 1 1 II. SAFETY Outdoor Driving Surfaces Y our power chair is designed to provide optimum stability under normal driving conditionsdry , level surfaces composed of concrete, blacktop, or asphalt. However , Pride recognizes that there will be times when you will encounter other surface types.
1 2 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 II. SAFETY Public Streets and Roadways WARNING! Y ou should not operate y our power chair on public streets and roadways. Be aware that it may be dif ficult for tr affic to see you when you ar e seated on your power c hair .
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 1 3 II. SAFETY T o eliminate the possibility of injury , Pride recommends that you or a trained attendant perform the following tasks before attempting a transfer: n T urn the power of f. See VIII. Operation.
1 4 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 II. SAFETY Reaching and Bending Never reach, lean, or bend while driving your power chair . If it is absolutely necessary to reach, lean, or bend while seated on your power chair , it is important to maintain a stable center of gravity and keep the power chair from tipping.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 1 5 III. EMI/RFI Electromagnetic and Radio Frequency Interference (EMI/RFI) Laboratory tests have shown that electromagnetic and radio frequency waves can have an adverse affect on the perfor- mance of electrically-powered mobility vehicles.
1 6 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 IV . THE JET 10 UL TRA THE JET 10 UL TRA The Jet 10 Ultra has two main assemblies: the seat and the power base. See figures 4 and 5. T ypically , the seat assembly includes the armrests, seatback, and seat base.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 1 7 IV . THE JET 10 UL TRA JET 10 UL TRA S PECIFICA TIONS Suspension: Active Trac Drive Wheels: 10 in., solid, (10 in., pneumatic are optional) Caster Wheels: 8 in., solid, rear-mounted Anti-tip Wheels: 5 in.
1 8 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 IV . THE JET 10 UL TRA REAR TRAPEZE BAR FRONT TRAPEZE BAR Figure 5. The Jet 10 Ultra Power Base FREEWHEEL LEVER MOTOR/BRAKE ASSEMBLY ARTICULATING .
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 1 9 IV . THE JET 10 UL TRA ELECTRICAL COMPONENTS The electrical components are located on the power base. The ammeter and the onboard AC power cord receptacle are located on the right side of the power base.
2 0 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 MANU AL FREEWHEEL LEVERS The Jet 10 Ultra has a manual freewheel lever on each motor . Manual freewheel levers enable you to disengage the drive motors from the gearboxes and maneuver the chair manually .
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 2 1 SEAT LATCH SAFETY Figure 10. Seat Latch V . ASSEMBL Y SEA T INST ALLA TION It may be necessary to install the seat either prior to initial operation or after transporting your power chair . Most seats ar e attached to the power base with the Universal Mounting System (UMS).
2 2 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 VI. COMFORT ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 2 3 Figure 12. Seat Mounting Holes VI. COMFORT ADJUSTMENTS 1 3 . Reinstall the seat. 14. Reconnect the controller to the power pod. 1 5 . Reinstall the rear shroud. Seat Position Y ou can move the seat forward or rearward by changing the extrusion mounting position.
2 4 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 T o change the armrest width: 1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 14. 2. Loosen the knobs. 3. Slide the armrests in or out to the desired width.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 2 5 VI. COMFORT ADJUSTMENTS 3. T urn the setscrew clockwise to lower the front of the foot platform. Controller Position Y ou can position the controller for either left-hand or right-hand use.
2 6 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 VI. COMFORT ADJUSTMENTS T o r otate the ELRs: 1. Push in release lever A. See figure 20. 2. Rotate the ELRs. T o adjust the ELR angle: 1. Push down release lever B. See figure 20. 2. Move the leg rest to the desired angle.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 2 7 VII. BA TTERIES AND CHARGING BA TTERIES AND CHARGING The Jet 10 Ultra uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level.
2 8 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 VII. BA TTERIES AND CHARGING Battery Break-in T o break in new batteries for maximum ef ficiency: 1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance level.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 2 9 VII. BA TTERIES AND CHARGING How can I get maximum range or distance per charge? Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves.
3 0 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 How can I ensure maximum battery life? A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair s batteries fully charged whenever possible.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 3 1 VIII. OPERA TION VSI CONTROLLER The electronic controller is what you use to operate your power chair .
3 2 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 Figure 23. VSI Controller Keypad VIII. OPERA TION Keypad The keypad is located in front of the joystick. It contains keys necessary to operate your power chair . See figure 23. On/Off Key The on/off key turns the VSI on and off.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 3 3 VIII. OPERA TION Horn Key The horn key activates the horn. Locking/Unlocking the VSI The VSI has a feature that enables you to lock your power chair to prevent unauthorized use. T o lock the VSI: 1. W ith the VSI powered on, press and hold the on/off k ey .
3 4 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 VIII. OPERA TION Battery Connector This connects the VSI to the power chair s batteries. Thermal Rollback The VSI controller is equipped with a thermal rollback circuit. The circuit monitors the temperature of the controller , which roughly translates to motor temperature.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 3 5 IX. CARE AND MAINTENANCE CARE AND MAINTENANCE Y our Jet 10 Ultra is a sophisticated power chair . Like any motorized vehicle, it requires routine maintenance checks. Y ou can perform some of these checks, but others require assistance from your authorized Pride Provider .
3 6 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 IX. CARE AND MAINTENANCE n The body shroud has been sprayed with a clear sealant coating. Y ou can apply a light coat of car wax to help it retain its high-gloss appearance. n Check all electrical connections.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 3 7 IX. CARE AND MAINTENANCE Storage Y our power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the power chair . See VII. Batteries and Charging.
3 8 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 IX. CARE AND MAINTENANCE Battery Replacement A battery wiring diagram is printed on a decal located on the battery tray . See VII. Batteries and Charging for correct battery specifications. WARNING! Pr ev ent injur y .
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 3 9 Figure 27. Battery Wiring Diagram IX. CARE AND MAINTENANCE 13 . Remove the back battery . 14 . Place a new back battery on the battery tray . Make sure that the terminals are facing forward. 15 . Fasten the reusable strap around the back battery .
4 0 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 X. WARRANTY FIVE-YEAR LIMITED WARRANTY For five (5) years from the date of purchase, Pride will repair or replace at our option to the original pu.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 4 1 X. WARRANTY SERVICE CHECKS AND WARRANTY SERVICE W arranty service must be performed by an authorized Pride Provider .
4 2 w w w .pridemobility .com Jet 10 Ultra/RevA/Apr04 NO TES.
Jet 10 Ultra/RevA/Apr04 www .pridemobility .com 4 3 NO TES.
Model # ____________ Serial # ____________ Fit and Finish Inclusion of all Parts Thank you for making the Jet 10 Ultra your choice in power chairs. We have thoroughly inspected your Jet 10 Ultra. The following checkmarks indicate that it has been tested, driven, and inspected.
デバイスPride Mobility Jet10Ultraの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pride Mobility Jet10Ultraをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPride Mobility Jet10Ultraの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pride Mobility Jet10Ultraの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pride Mobility Jet10Ultraで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pride Mobility Jet10Ultraを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPride Mobility Jet10Ultraの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pride Mobility Jet10Ultraに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPride Mobility Jet10Ultraデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。