ProfileメーカーCD8200の使用説明書/サービス説明書
ページ先へ移動 of 20
AM/FM HIGH POWER DETACHABLE FACE CD PLAYER CD8200 INSTALLATION INSTRUCTIONS / OWNER S MANUAL ,.
1 Serial # Purchase Date I NTRODUCTION Congratulations on your purchase of a Profile state-of-the-art single disc CD player. Your selection of a Profile car audio product indicates a true appreciation of fine musical reproduction.
2 CD8200 S AFETY PRECAUTIONS Secure the CD player When installing your CD player in the vehicle, make sure it is mounted properly in the dash, using an after market installation kit if needed. When using the supplied mounting sleeve, it is a must that you also use the supplied back brace to support the back of the CD player.
3 C ARE AND MAINTENANCE PROTECTIVE CASE ( FIG.2) Press the OPEN button to detach the face plate, then take the face plate away from the head unit (Fig.1) and put it in the protective case (Fig.2) for safe keeping. FACE PLATE OPEN BUTTON ( FIG.1) Cleaning the CD player When cleaning the vehicle, be sure not to get any water in or on the CD player.
4 CD8200 DISC CARE AND PLAY: Before playing, clean the disc with a clean, lint-free cloth. Wipe the disc in the direction of the arrow. Do not use solvents such as benzine or thinners. Commercially available cleaners or anti static spray will damage the unit.
5 E LECTRICAL AND SIGNAL CONNECTIONS FOUR SPEAKER SYSTEM ! Connect Black wire to chassis ground. ! Connect the Yellow memory backup wire to a Constant +12 Volt power source wire. ! Connect the Red ignition wire to a switched +12 Volt power source wire.
6 CAUTION! Tape unused wires so they do not short against other wires or chassis ground. TWO SPEAKER SYSTEM CD8200 NOT USED NOT USED NOT USED NOT USED + + + + YELLOW ANTENNA CONNECTOR MEMORY +12V BLAC.
7 M OUNTING THE CD PLAYER DIN SLEEVE MOUNTING Insert the mounting sleeve into a standard DIN cutout in the dash kit, dashboard or Console. Bend the mounting tabs of the sleeve with a screwdriver to secure the bracket firmly in place. Insert the CD Player in the mounting sleeve until it locks.
8 CD8200 Attach the back brace to the CD player using the supplied hardware. Then attach the other end of the brace to a firm mounting surface (i.e. Dash brace, fire wall, e.t.c.) This will brace the back of the CD player to ensure solid mounting to prevent theft and provide optimal CD play.
9 R EMOVING THE CD PLAYER Remove the rectangular trim ring by applying pressure with your finger tips, then gently pull out away from the dash. PLACE FINGER TIPS HERE I SO/DIN MOUNTING If you own a Ja.
10 CD8200 LOCATION AND FUNCTION OF CONTROLS.
11 1 POWER To t u r n O N t h e unit, press any button except the and button. To t u r n O F F t h e unit, press the button for more than 2 seconds. 2 DETACH FACE PLATE Press the button to detach the face plate. This will allow you to remove the face plate.
12 In CD play mode, press and hold the 9 or 10 button to fast forward or fast reverse through the song. The CD resumes playing when the button is released. 11 PRESET STATIONS There are 6 numbered buttons to store into memory and recall stations for each band.
13 BEEP - The beep sound when you press a button on the unit can be turned on or off. Press the SEL button for more than 2 seconds to display the DSP function. Press the SEL button again momentarily to display BEEP ON/OFF. Then use 5 button to turn on/off the beep sound.
14 16 RANDOM PLAY In CD play mode, press the RDM 16 button to play all tracks of the disc in random sequence. Press it again to cancel random play. 17 LOUDNESS Press LOU button once to enhance the bass effect. Press again to cancel the loudness effect.
15 T ROUBLE SHOOTING THE SYSTEM The following chart will help in solving most problems that may occur. Should any problem persist after you have made these checks, please consult your nearest Profile retailer. Before going through this check list, refer back to the wiring and operating procedures.
SYMPTOM CAUSE SOLUTION The installation angle is greater than 30 degrees Adjust the angle of the unit to l ess than 30 degrees The disc player is installed incorrectly Check to see if the unit is fastened securely with the back brace supporting the rear of the unit.
S PECIFICATIONS GENERAL Power Supply Requirements...........................................DC 12 Volts, Negative Ground Chassis Dimensions ...................................................................7 (W) x 6 1/2 (D) x 2 (H) Tone Controls.....
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser.
PROFILE CONSUMER ELECTRONICS, INC. 15060 SHOEMAKER AVE SANTA FE SPRINGS, CA 90670 TEL: (562)404-9393 FAX: (562)404-9433 WWW.PROFILEUSA.COM WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period.
デバイスProfile CD8200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Profile CD8200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはProfile CD8200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Profile CD8200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Profile CD8200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Profile CD8200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はProfile CD8200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Profile CD8200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちProfile CD8200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
