Promise TechnologyメーカーC6101SSWP000000-2の使用説明書/サービス説明書
ページ先へ移動 of 18
Copyright Copyright by Promise Technology, Inc. (“Promise”), 1999. No part of this manual may be reproduced or transmitted in any form without the expressed, written permission of Promise. Trademarks All trademarks are the property of their respective holders.
SuperSwap Manual ii Table of Contents Introduction ............................................................................... 1 Specifications ____________________________________ 1 Interface ......................................................
SuperSwap Manual 1 Introduction Thank you for purchasing Promise Technology’s SuperSwap. The SuperSwap drive housing installs easily into any 5. 25” component bay in your PC. SuperSwap’s drive carrier and housing extend the data storage capabilities of your system by allowing you to easily swap most 3.
SuperSwap Manual 2 • 5% to 95% (non - condensing) Warranty • Two years limited parts and labor.
SuperSwap Manual 3 Key Features The following a re key features of the Promise SuperSwap: Drive Types • Supports standard IDE drives (Ultra ATA, DMA, and EIDE) • Supports Ultra ATA/100 and Ultra ATA/66.
SuperSwap Manual 4 Getting Started This section is designed to help prepare SuperSwap for installation into your personal computer. Please read through this chapter carefully before attempting to install SuperSwap.
SuperSwap Manual 5 Installing Drive Housing Assembly Installing SuperSwap into your PC is a simple process. There are two basic components involved: installing the housi ng assembly in your system; and installing a hard drive in the drive carrier.
SuperSwap Manual 6 Figure 2 - 1: SuperSwap Housing Assembly Figure 2 - 2: SuperSwap Housing Assembly Rearview NOTE: If using the SuperSwap solely as a SLAVE device, make certain to connect the end of the IDE Cable (not to the middle) to the SuperSwap Chassis.
SuperSwap Manual 7 Removing/Installing Drives The Promise SuperSwap is designed to w ork with several Promise ATA RAID controllers that can support RAID 1 (SuperTrak100/66, FastTrak100/66), RAID 3 (SuperTrak100/66), or RAID 5 (SuperTrak100/66).
SuperSwap Manual 8 with two matching sets of numbered stickers. Place one sticker on the front of the drive housing assembly and the matching number ed sticker on the front of the drive carrier.
SuperSwap Manual 9 Usually dark or black, LED lights green when disk is accessed..
SuperSwap Manual 10 Troubleshooting Event: The drive status LED is red. Cause: This shows a failed drive. A failed drive may be marked as such because of power failure or m edia access problem (such as a bad sector which fails retry).
SuperSwap Manual 11 Fix: Make sure that there is indeed a drive installed correctly in a drive carrier with the power and data cables properly attached. Cause: The drive is not jumpered correctly. Fix: Consult your drive manufacturer’s manual or the drive casing itself and jumper the drive for “single” drive operation.
Appendix A A - 1 Limited Warranty Promise Technology, Inc. (“Promise”) warrants that for two (2) years from the time of the delivery of the product to the original end user: a) the product will conform to Promise’s specifi cations; b) the product will be free from defects in material and workmanship under normal use and service.
Appendix A A - 2 Promise does not warrant that any product is free from errors or that it will interface without problems with your computer system. It is your responsibility to back up or otherwise save important data before installing any product and continue to back up your important data regularly.
Appendix B B - 1 Returning Product For Repair If you suspect a product is not working properly, or if you have any questions about your product, con tact our Technical Support Staff through one of our.
Appendix B B - 2 When repairing returned product(s), Promise may replace defective parts with new or reconditioned parts, or replace the entire unit with a new or reconditioned unit.
Appendix B B - 3 P/N: C6101SSWP000000 - 2.
デバイスPromise Technology C6101SSWP000000-2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Promise Technology C6101SSWP000000-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPromise Technology C6101SSWP000000-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Promise Technology C6101SSWP000000-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Promise Technology C6101SSWP000000-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Promise Technology C6101SSWP000000-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPromise Technology C6101SSWP000000-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Promise Technology C6101SSWP000000-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPromise Technology C6101SSWP000000-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。