PYLE AudioメーカーPP-5200の使用説明書/サービス説明書
ページ先へ移動 of 28
Rev.: A0 Aura Series (PP - 5000 / PP - 5200) Thermal Printer User's Guide IMPORTANT!!!! Please read carefull y before using this printer Before opening the Top Hood, make sure there is no paper jam or cutter jam trouble. (Read page 3 - 4 , 3 - 5 and Warranty Limit in the user’s Manual.
P/N: 19740900010 Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
i Table Of Contents GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 1 -- 1 CONGRATULATION . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 PRODUCT BRIEFING . . . . . . . . . . . . . . . . . . . . . 1 -- 1 UNPACKING . . . . . . . . . . . . .
ii Printing problems . . . . . . . . . . . . . . . . . . . . . 3 -- 2 Paper jam problems . . . . . . . . . . . . . . . . . . . 3 -- 4 Auto cutter problems . . . . . . . . . . . . . . . . . . 3 -- 4 Advanced analysis tool . . . . . . . . . . . . . . . .
1 - 1 I. GETTING STARTED A. CONGRATULATION You have made a very wise decision by purchasing the easy loading ; low noise ; high resolution ; light weight ; high reliability thermal printer Aura (PP - 5000 & PP - 5200) series of Posiflex products.
1 - 2 Aura series also supports user’s company’s LOGO downloading for superior performance. It even supports some enhancement capability for reminder fun ction to persons around. It can be used to drive a separately purchased kitchen bell for such reminder function in noisy environment.
1 - 3 ordered). b Power supply cable (when no power adaptor ordered) This printer power supply cable is used to supply power to the printer from the Posiflex POS system.
1 - 4 F. INDICATORS • Power LED: green • Error LED: red • Paper Out LED: red Parallel Connector Serial Connector Power Connector Peripheral Connector Rear View Screws Window Plate Screw Setup Wi.
2 - 1 II. QUICK START - UP A. LOADING PAPER 1. Desk top application 1. Press down the hood release button to release the top hood. 2. Raise the released hood wide open manually. 3. Drop the thermal paper roll inside the printer in the orientation as shown in the picture.
2 - 2 2. When to rep lace paper Whenever the printer gives paper out signal or a red line appears on the thermal paper, it is the proper timing for replacing the paper.
2 - 3 keep parallel interface in fast operation, please adjust in setup window the switch positions both 1, and 2 to ON leaving the rest unchanged as factory default setting . 3. Peripheral connection The peripheral co ntroller is a 6 pin RJ11 jack between the power connector and the parallel connector.
2 - 4 5. Power on When all the above cable connections are made correctly, you may connect your power adaptor to the wall outlet. Make sure that the ty pe of power cord and the voltage requirement of the power adaptor meet the local power conditions. Now the printer is ready for power on.
2 - 5 The header is printed in text mode and the rest part of this slip is printed in page mode. If FEED button is pressed at this moment, a font table will be printed in text mode again. To exit the test printing, please turn the printer off and on again.
2 - 6 either paper near end sense or paper feed action. It is also noticed that some market available paper roll has extremely light bobbin, easi ly causing the paper roll to go off position when paper feeding with low remaining paper.
3 - 1 III. MAINTENANCE GUIDES A. MAINTENANCE GUIDE LINES • Always turn off and disconnect power before opening the hood or cover. • The areas around the print head and motor become very hot during and just after printing.
3 - 2 Before putting back the paper roll for printing, alcohol solvent must be dried completely. D. TROUBLE SHOOTING This section gives solutions to some printer problems you may have.
3 - 3 If there is no paper jam and the print head is not overh eated, turn off the printer and wait for half a minute then turn it back on. If the problem still remains, contact a qualified service person.
3 - 4 setup and changing the switch positions 1 and 2 in the printer setup window to ON may he lp. 3. Paper Jam Problems Paper is jammed inside the printer – Turn off the printer and open the top hood by releasing the hood lock. Remove the jammed paper and reinstall the paper roll.
3 - 5 cutter blade along the track and reset it to home position. Please test push the top hood release button from time to time to see if the hood opens as result of cutter position reset. Close the cutter cover back when done. For PP - 5200 please refer to pictures below and lift up a transparent protective cover over the adjustment wheel.
3 - 6 Please use manual cutter as temporary alternative measure once the auto cutter malfunctioned. 5. Advanced Analysis Tool This printer supports Hexadecimal Dump for experienced user to view exact ly what data is received by the printer. This can be useful in finding software problems.
4 - 1 IV. SPECIFICATIONS A. PRINTER ITEM SPECIFICATION Printing method Thermal sensitive line dot method Effective printing width 54 mm Ther mal head configuration 432 dots / line PP - 5000 120 mm /sec.
4 - 2 C. POWER ADAPTOR ITEM REQUIREMENT INPUT VOLTAGE 100 V AC ~ 250 V AC INPUT FREQUENCY 50 ~ 60 HZ INPUT CURRENT 1.5 A MAX. @ 115 V AC OUTPUT VOLTAGE + 24 V DC OUTPUT POWER 60 W STATIC LOAD 0 A ~ 2.
5 - 1 V. TECHNICAL INFORM A TION A. INTERFACES 1. Peripheral interface The connector for peripheral control is a 6P6C RJ11 jack with the following pin assignment. The best recommended cash drawers to this connector are Posiflex CR3100, CR3200, CR4000 and CR4100.
5 - 2 2. Serial interface The serial interface cable is a RJ45 plug to DB9F cable of length 1.8 meters (about 6 feet). To use the serial interface with a distance longer than the cable length can be achieved through use of LAN cable and a RJ45 jack to DB9F converter.
5 - 3 points t o the connector area of the printer. The OFF direction points to the power switch. The functions of each position may evolve with the revisions of the firmware. The information below applies to the latest version to the date of print of this manual.
5 - 4 Fo r switch position 5, if the switch is set to ON, the busy signal is sent to host only when input buffer is full. When it is set to OFF, busy signal is sent to host whenever an off line status occurs. Therefore, signals including the paper near end detect w ill generate busy signal to the host.
6 - 1 VI. USEFUL TIPS • Please note that only those qualified technicians may adjust s everal jumpers for some technical settings . P lease visit our web site http://www.posiflex.com or http://www.posiflex.com.tw for detail s of th e technical information such as driver installation, DIP switch settings and command sets etc.
6 - 2 • Do not use a power outlet of a circuit shared with any equi pment that uses a lot of power or causes great electrical noises, such as a copier, electric motors or a coffee m aker. • Do not use thermal paper containing Sodium (Na+), Potassium (K+) and Chlorine (Cl - ) ions that can harm the print head thermal elements.
デバイスPYLE Audio PP-5200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
PYLE Audio PP-5200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPYLE Audio PP-5200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。PYLE Audio PP-5200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。PYLE Audio PP-5200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
PYLE Audio PP-5200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPYLE Audio PP-5200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、PYLE Audio PP-5200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPYLE Audio PP-5200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
