Quatechメーカー4-Port USB 2.0 Device Server over IP USBN-500の使用説明書/サービス説明書
ページ先へ移動 of 18
Quatech Model USBN-500 Network USB2.0 Device Server Over IP 4-Port USB2.0 Device USER MANUAL.
USB Device Server Windows Client User Manual TABLE OF CONTENTS 1. Introduction______________________________________________________________3 2. Windows utility____________________________________________________________3 2.1. Virtual USB-IP Driver Software_________________________________________4 2.
2. Windows utility USBIP Admin utility Setup is an Install Shield ba sed application, which can be used for installing, uninstalling and upgrading this USB device server Client S/W. Pl ease run the self-explanatory Install shield application to install this USB device se rver Admin Utility.
USBIP Admin tool The application has four panels, wh ich are docked in the application. 1) Main window: This displays all the Device server and the USB Devices connected on them 2) Function Panel: This panel enables to switc h between the Device Mapping and Server Manager Application.
and the Operating System autom atically searches for the driver until the Virtual USB over IP driver is installed. Make sure that you click on “Continue anyway” if a Windows dialog pops up about the Digital Signature as shown below.
2.3. Server Manager Server manager enables the Administrator to c onfigure the USB device server on the network. The Server Manger also has an option to s earch for the USB servers on the Network. Right Click on Server Manager Main window and Click on “Search server” as shown below.
It pops up the ‘Searching for Servers’ dialog and li st all the USB device se rvers on the Network as shown below The USB Device Server search is password protected and should be unlocked in order to configure the selected device.
On selecting ‘Un-Lock’ the password dialog pops up as shown below. Key in the password in the ‘Password’ dialog. The default password for the USB IP Server is “usbip” If the Authentication is successful a ‘Unlock OK’ dialog appears. Now the Device server can be configured for various settings as given below.
The Basic Settings page allows you to specify a server name .Check the modify box and enter server name as shown below. IP Settings Page: The IP Settings page allows you to modify the US B device server IP Address as shown below. The Default IP Address is 192.
After Selecting IP Configuration key in the IP Ad dress of the USB device server in the IP Address field followed by proper Subnet Mask & Gate Way as shown below. After entering IP address, Subnet Mask & Gate Way then click on “save” button.
Check the Modify box to Enable or Disable password option to the USB device server. b) Upgrade Firmware This USB device server Firmware can be upgraded remotely using the Firmware upgrade option. Select the server on the Server manager. Right Click on the server and Select Upgrade Firm ware option to upgrade the firmware.
As soon as the transfer is completed, the USB de vice server automatically restarts to apply the upgraded firmware settings. c) Restore factory defaults Right click on the USB device server under Serv er Manager Window and select the Restore Factory Defaults function to obtain Default settings as shown below.
the Printer Auto Reconnect button on the Menu bar to open the Printer Auto-Connect Window. Select the Printer which was connected a nd Click on “Save” and close the Window.
browser, which will displays the default hom e page of the Server. Def ault IP address is 192.168.3.22, for USB Server application & the USB devi ce server will have this IP address when USB Server Firmware is loaded on to it. http://192.168.3.22 On password prompt please give ‘ admin ’ as user name and ‘ usbip ’ as password.
For the wired interface you can configure the Stat ic IP, Subnet Mask, and Gateway m anually or set the box to automatically obtain an IP address by setting to the Dyna mic (DHCP) mode. 3.4. Status Page The status page displays the current status of the USB devices attached.
a ) T h r e a d S t a t u s : T h r e a d S e s s i o n H o s t A c t i o n b ) S e r v i c e S t a t u s : S e r v i c e S t a t u s C o n t r o l c ) D e v i c e S t a t u s : Vendor Id Product Id C.
An upgrade.tar.bz2 file is required to upgrade the firmware. Click on “upgrade” to upgrade the firmware.
A file successfully uploaded message is displaye d and the webpage also indicates that the USB device server is restarting to a pply the upgraded firmware settings.
デバイスQuatech 4-Port USB 2.0 Device Server over IP USBN-500の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Quatech 4-Port USB 2.0 Device Server over IP USBN-500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはQuatech 4-Port USB 2.0 Device Server over IP USBN-500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Quatech 4-Port USB 2.0 Device Server over IP USBN-500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Quatech 4-Port USB 2.0 Device Server over IP USBN-500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Quatech 4-Port USB 2.0 Device Server over IP USBN-500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はQuatech 4-Port USB 2.0 Device Server over IP USBN-500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Quatech 4-Port USB 2.0 Device Server over IP USBN-500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちQuatech 4-Port USB 2.0 Device Server over IP USBN-500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
