Radio Shackメーカー21-1703 Aの使用説明書/サービス説明書
ページ先へ移動 of 16
Thank you for purchasing your Mini Mobile CB Radio fr om RadioShack . Please read this user’ s guide before installing, setting up and using your new product.
2 C ontents Product F eatures ......................................................................... 3 Setup .......................................................................................... 4 Attaching the Microphone Holder .. ...........
3 Product F eatures Other F eatures Full Legal Power – gives you the greatest available range. Automatic Noise Limiter – reduces impulse-type noises while r eceiving. External Speaker Jack – provides a connection for an external speaker . Phase-Locked Loop (PLL) Frequency Synthesizer – pr ovides highly accurate and stable tuning.
4 Setup Setup Attaching the Microphone Holder Y ou can attach the microphone holder to either side of the transceiver or to another location in your vehicle. T o attach the holder to either side of the transceiver , secure the holder to the side using the supplied 3mm self-tapping screws, and spring washers.
5 Setup Mounting the T r ansceiver Cautions: • If you use this CB in a vehicle, mount it securely to avoid damage to the CB or vehicle, or injury to anyone in the vehicle during sudden starts or stops. • Do not mount the CB wher e it could damage or interfere with the operation of any passive restraint safety device (an airbag or seat belt).
6 Setup Connecting an Antenna There ar e many differ ent types of CB radio antennas for mobile CBs. Each type has its own benefits, so choose the one that best meets your needs. Note: If you are using this CB as a base station, see “Using the T r ansceiver ” on p.
7 Setup Connecting the Microphone 1. Press the tab on the side of the supplied micr ophone’ s plug and insert the plug into the MIC jack on the front of the transceiver . Be sure the tab is aligned with the jack’ s notch. 2. Slide the microphone onto the micr ophone holder .
8 Setup Using V ehicle Batter y Power T o connect the transceiver to the vehicle battery power: 1. Connect the red wir e (with the inline fuse holder) on the back of the transceiver to a point in your vehicle’ s fuse block that has power only when the ignition is in the ACC (accessory) or ON position.
9 Oper ation Oper ation Receiving T r ansmissions and Adjusting SQUELCH 1. Rotate SQUELCH fully counterclockwise. 2. Rotate VOLUME clockwise until it clicks to turn on the transceiver . The turn on the transceiver . The channel display lights and the channel appears, and the RX indicator lights.
10 Oper ation Oper ational Hints Common Uses for CB Radios • W arn of traffic tie-ups ahead. • Help truck drivers and delivery personnel learn r oad and traffic conditions and get assistance in locating destinations. • Pr ovide fast help in the event of emergency or br eakdown.
11 Oper ation This table lists codes adopted by the Associated Public Safety Communications Officers (APCO) Code Meaning 10-1 Y our signal is bad. 10-2 Y our signal is good. 10-3 Stop transmitting. 10-4 Message was received and understood. 10-5 Relay information to ___.
12 Additional Infor mation T roubleshooting If your CB is not working as it should, follow these suggestions to see if you can eliminate the problem. If you cannot, take the CB to your local RadioShack stor e for assistance. Symptom Check/T ry CB has trouble r eceiving.
13 Additional Infor mation • Make all CB power and antenna wir es as short as possible. • Route the power wir es away from the antenna wir es. • Be sur e that the chassis ground connection is secur e. • Replace old ignition wir es with new , high-voltage, noise suppression wires.
14 Additional Infor mation Specifications Receiver Frequency coverage ............... all 40 CB channels (class D) 26.965 - 27.405 MHz Sensitivity for 10 dB S/N ................................................................................ 0.6 μV Tight squelch limit .
15 Additional Infor mation RF Emissions W ARNING! The Federal Communications Commission has adopted a safety standard for human exposur e to radio frequency electr omagnetic energy emitted by FCC regulated transmitters. It is up to the user to pr operly operate this radio transmitter to ensure safe operation.
21-1703 A P/N: AO0309AAA1 06A08 Printed in China ©2008. RadioShack Corporation. All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation. Protect the envir onment by recycling used electronics. Go to www .ecyclingcentral.
デバイスRadio Shack 21-1703 Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Radio Shack 21-1703 Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRadio Shack 21-1703 Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Radio Shack 21-1703 Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Radio Shack 21-1703 Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Radio Shack 21-1703 Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRadio Shack 21-1703 Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Radio Shack 21-1703 Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRadio Shack 21-1703 Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。