RangerメーカーRCI-5054DXの使用説明書/サービス説明書
ページ先へ移動 of 11
RCI-5054 DX AM/FM/SSB/CW 6 Meter Amateur Mobile Transceiver DIM NB/ANL MEM PRG SCAN SPLIT SWR R.BEEP MAN ENT LOCK SHF RCI−5054 DX CLR GAIN RF LSB FM USB AM OFF CW PA RF MIC PWR VOL SQ Owner's Manual - 1 - Table of Contents Chapter 1 Specifications .
- 2 - Chapter 1 Specifications GENERAL Model RCI-5054DX Frequency Range : 50.000 ~ 54.000 MHz Tuning Steps 100 Hz, 1 KHz, 10 KHz, 100 KHz, 1 MHz Emission USB, LSB, CW, AM, FM Frequency Control Phase-Lock-Loop Synthesizer Frequency Tolerance 0.005% Frequency Stability 0.
- 4 - Chapter 3 Installation The RCI-5054DX is easy to install. All necessary parts (less the antenna and coax cable) have been included to facilitate installation. Transceiver Mounting Choose a suitable location for th e transceiver that will allow easy access to the front panel as well as proper air circulation to the back of the unit.
- 6 - SWR DIM SCAN MEM LOCK ENT AM FM RCI−5054 DX MAN R.BEEP NB/ANL SPLI T PRG SHF CLR GAIN RF USB LSB CW OFF RF MIC PWR VOL PA SQ 9 24 15 10 11 16 17 12 18 13 14 19 20 21 21 6 7 8 35 24 23 22 1 Chapter 4 Operation Front Panel 1. FREQUENCY SELECTOR : Used to set the desired transmit and receive frequency.
- 8 - special circumstances. We discourage use of this feature in normal operation, as it can be annoying to other operators. 11. SPLIT BUTTON (SPLIT) : Enables the offsetting of the transmitter frequency by up to +/- 2 Mhz (programmable) for FM repeater operation.
- 10 - 2 3 4 5 1 Operation (Continued) Rear Panel 1. ANTENNA : This jack accepts a 50 oh ms coaxial cable with a PL-259 style plug. 2. C W K E Y : The CW key is used for Morse Code operation. To operate connect a CW key to th is jack, and place the mode switch in the CW position.
- 12 - Operation (Continued) Frequency Selection Frequency selection in the RCI-5054DX can be accomplished using any one of the following three methods: 1. The first method of frequency selection uses the SHF (Shift) key and the ▲ (UP)/ ▼ (DOWN) keys located on the front panel .
- 14 - Chapter 5 Programming Receive Scanning The receive scanning feature helps locate active frequencies within a preprogrammed band segment anywhere on the 6 Meter band (refer to SCANNING, page 16). To begin scanning, slowly turn the Squelch control clockwise until the receiver noise disappears.
- 16 - . Chapter 6 Frequency Scanning Frequency scanning can be achieved by either of two methods: the first method involves scanning of all frequencies between a pre-set upper and lower scan frequency. The second method permits the scanning of frequencies previously programmed in the memory locations 0 thru 9.
- 18 - Chapter 7 Offset (Split) Frequency Operation The split frequency function offsets the transmitter frequency either above or below the receiver frequency by a user-programmable amount. This is necessary for op erating on FM repeaters. In the following example, the programmi ng of a 1 MHz offset will be described.
- 20 - LIMITED WARRANTY Ranger Communications, I nc. ( Ranger ) warrants to the original purchaser ONLY this product against defects in material or workman ship as follows: 1 ) Ranger warrants the pro.
デバイスRanger RCI-5054DXの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ranger RCI-5054DXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRanger RCI-5054DXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ranger RCI-5054DXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ranger RCI-5054DXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ranger RCI-5054DXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRanger RCI-5054DXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ranger RCI-5054DXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRanger RCI-5054DXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。