Razorメーカー300001-SLの使用説明書/サービス説明書
ページ先へ移動 of 20
OW NE RS M AN UA L Read and understand this e ntire manual before riding! Electric-P ower ed Go Kart Item Number 300001-SL ®.
NOTE: This manual contains many “Warnings” and “Cautions” concerning the consequences of failing to maintain, inspect or properly use your Ground Force. Because any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death each time such a warning is mentioned.
• Always check and obey any loacl laws or regulations which may affect the locations where the Ground Force may be used on public property . The Ground Force is meant to be used only in controlled environments free of potential traffic hazards, and not on public streets or side - walks.
NOTE: Do not activate the speed control on the setting wheel unless you are in a safe, outdoor environment. Use this product only in areas free of potential traffic hazards and not on public streets or sidewalks. W ARNING: REGARDING USE OF NON-RAZOR PRODUCTS WITH YOUR RAZOR GROUND FORCE.
W ARNING: Failing to properly adjust and tighten the screws, nuts and bolts that affix the steering wheel and seat can cause you to lose control and c rash.
T ighten securely . Position the tie-rod control arm onto the steering axle as shown in Figure 3a and install the washers and fixing bolt. Using a 10 mm wrench, tighten securely .
❏ 2 D. Optional attaching the seat with seat belt assembly . Locate the four (4) long seat attachment screw and seat-belt assembly in the parts bag. Position the seat over the frame and align it with the holes in the frame. Position the seat-belt anchors with the lap/shoulder assem- bly on the left side and the receiver latch on right side.
Figure 6a Figure 6b W ARNING: Practice in an open area free from obstacles until you are famil- iar with the brake function. A void skidding to a stop as this can cause you to lose control as well as cause damage in the rear tires. ❏ 2 F . Charging the battery prior to use.
❏ 2 G. Circuit breaker . The circuit breaker (next to charger input port in Figure 7a) will automatically shut off the power to the motor in the event an overload condition is placed on the motor . An excessive overload, such as too heavy a driver or too steep a hill, could cause the motor to overheat.
❏ 4 A. ADJUSTING THE BEL T . The circuit breaker (next to charger input port in Figure 7a) will automatically shut off the power to the motor in the event an overload condition is placed on the motor . An excessive overload, such as too heavy a driver or to NOTE: T urn power switch off before maintenance procedures.
❏ 4 B. WHEEL REMOV AL PROCEDURE. Occasionally the wheels need to be replaced when worn out. The front and rear wheels are iden- tical and can be interchanged. The only difference is how the wheels at- tach. The rear wheels are keyed to the rear axle, while the front wheels have bearings (608ZZ = standard skateboard bearings).
4B-3.) T o replace a rear wheel, make sure the keys are properly seated in the axle and aligned with the key ways in the wheel (Figure 11). T ighten the self-locking nut securely . NOTE: The razor logo on the tread must face out. ❏ 4 C. REPLACING THE BEL T .
Figure 12a Figure 12b 4C-4.) Remove the brake guard and, using the small Allen key , loosen setscrew to release the brake drum. This may or may not require the loosening of the brake cable to gain access to the fixing screw . Loosen the drive pulley in the same manner .
5. SAFETY THE FOLLOWING RECOMMENDA TIONS ARE EXPECTED FROM: ASTM F1928-98, “ST ANDARD SAFETY GUIDE FOR CONSUMER RECREA TIONAL Y USE OF FUN-CARTS” Go kart shall not be operated with any modifications to the kart or it’ s components.
6. ADDITIONAL RAZOR SAFETY WARN INGS W ARNING: Maintain a hold on the steering wheel at all times. W ARNING : Never use near steps or swimming pools. W ARNING : T raffic can be fatal.
7. ILLUSTRA TED P ARTS BREAKDOWN See Figure 14 (Specifications and parts list subject to change without notice) ITEM# DESCRIPTION QUANTITY 1 Wheel 2 Pindle, right 3 Bearing, 608ZZ 8x22 4 T ie-rod 5 B.
ILLUSTRA TED P AR TS BREAKDOWN Figure 14.
8. RAZOR LIMITED WARRANTY & REGISTRA TION The manufacturer warranties this product to be free of manufactur - ing defects for a period of 90 days from date of purchase.
SB 1918 (CALIFORNIA) DECLARA TION: YOUR INSURANCE POLICIES MA Y NOT PROVIDE COVERAGE FOR ACCIDENTS INVOL VING THE USE OF THIS SCOOTER/ELECTRIC VEHICLE.
IMPORT ANT! If your Razor has a problem call Razor USA toll free (866) 467-2967 QUESTIONS: Please read the owner’ s manual thoroughly . If you still have questions, check our website for updates and contact information.
デバイスRazor 300001-SLの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Razor 300001-SLをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRazor 300001-SLの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Razor 300001-SLの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Razor 300001-SLで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Razor 300001-SLを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRazor 300001-SLの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Razor 300001-SLに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRazor 300001-SLデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
