RBH Soundメーカー1001RBの使用説明書/サービス説明書
ページ先へ移動 of 16
1001RB Series Owner s Manual 1001RB 1001RB/1 15 1001RB/210.
2 1001RB Series Table Of Contents Gallien-Krueger 2 24 0 Pa ra g on D r . San Jose, CA, 95131 phone: 408-441-7970 fax: 408-441-8085 w w w . g a llien-krueger .com Em ail: sales@gallien.com Introduction..................................................
3 1001RB Series Congratulations Y our purchase of a new Gallien-Krueger 1001RB Series product is surely the result of much careful consideration on your part. For our part, we at Gallien-Krueger are pleased that you chose us, and are determined that you will be a satisfied customer .
4 1001RB Series Always Listening I have never seen the point in doing things the way others have done them. I also have not been very interested in following the latest fad. I am a Stanford educated engineer who worked his way through school as a musician.
5 1001RB Series Quick S tart The 1001RB Series is designed to be simple to operate. All controls have a well defined purpose and are well behaved. These directions will take you through the basics and give you a good start for setting up your sound.
6 1001RB Series Sound Tips The1001RB Series has several unique features which, if used properly , will obtain that sound you have been searching for . The Equalizer: The Equalizer is used to fine tune your sound. When adjusting it, do it just a little at a time.
7 1001RB Series Bi-Amp and Normal Operation The 1001RB ’ s unique design makes setup for Bi-Amp or normal configuations simple. The operational mode is configured by how you connect your speaker cabinets. In addition, you have the option of driving one cabinet in Bi- Amp and one in Normal operation.
8 1001RB Series Safety Information . . . . Safety Information V erify Line, V oltage and Amperage Before Use: Y our new 1001RB Series Bass Amp has been factory configured for use with: · 120 V olt/60Hz 20 Amp circuit for USA & Canada. · 230 V olt/50Hz 10 Amp circuit for Europe & Australia.
9 1001RB Series Installation and Maintenance Installation: · T o insure proper operation and to avoid potential safety hazards, place the unit on a firm, level surface. When installing the unit in a rack, be sure the mounting hardware can support the amplifier ’ s weight.
10 1001RB Series Front Panel Controls 1-Balanced Direct Out: An electronically balanced output, that you can run to your P .A. system. 2-Pre/Post EQ Button: Selects the direct out signal from before or after the EQ. 3-Direct Level Out Controls the level at the direct out jack.
11 1001RB Series Rear Panel Controls 1- AC Receptacle: The power cord is detachable and plugs in here. 2- 540W Amp Only: 540W power amp output for Full-Range operation only . They deliver 540 watts into 4 Ohms. Lower impedances should not be used. Each jack has a minimum of 8 Ohms each.
12 1001RB Series 1001RB Series Combos The 1001RB Series combos deliver the1001RB ’ s unique features and distinct sound by using a variety of internal speaker configurations, GK ’ s RBH cabinet technology and a unique Lock N ’ Roll transport system.
13 1001RB Series T ech T alk Characteristics of the 1001RB: The1001RB Series is a flexible, state-of-the-art Bass Amplifier , designed to deliver maximum performance, and be simple to operate.
14 1001RB Series T ech T alk Electronic Crossover: Bi-Amp systems allow the crossover to be electronic and therefore, have much higher quality than passive cross- overs. A crossover separates the sound into two parts (high and low frequency). The highs are sent to the horn or high frequency cabinet and the lows are sent to the woofer .
15 1001RB Series Tech Talk Cool Running = Reliability: The 1001RB Series uses a “ dual rail power supply ” that generates about half the heat of conventional amplifiers. Low output signals run off a low voltage supply , and high level signals run off a high voltage supply .
16 1001RB Series 1001RB Series Owner s Manual Part #160-0030-A Printed in the U.S.A. Block Diagram 1001RB Series Specifications: Output Power: 540W Amplifier 540W @ 8 Ohms 540W @ 4 Ohms 50W Amplifier 50W @ 8 Ohms 50W @ 4 Ohms Input Section: Maximum Input Level 0.
デバイスRBH Sound 1001RBの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
RBH Sound 1001RBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRBH Sound 1001RBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。RBH Sound 1001RBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。RBH Sound 1001RBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
RBH Sound 1001RBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRBH Sound 1001RBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、RBH Sound 1001RBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRBH Sound 1001RBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
