Audiovoxメーカー1181293の使用説明書/サービス説明書
ページ先へ移動 of 12
INSTALLATION INSTRUCTIONS FOR 50 - 0210F - 002 SERIES 1181291 50 - 0210F - 003 SERIES 1181292 50 - 0210F - 004 SERIES 1181293 SUBURBAN OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business.
2 MATERIALS PROVIDED FOR INSTALLATION: ITEM Description QTY 1 SCREW, # 8 X 3/4" HWH ,TEK,Z1 4 2 SCREW, # 8 X 2 1/2" PFH ,ZII 3 3 SCREW, # 8 X 1 1/4" PWH ,BZ 4 4 CONSOLE 1 5 MOUNTING BRA.
3 I. PREPARATION OF VEHICLE INTERIOR 1. Remove the O.E.M. compartment console currently mounted to inner roof of v ehicle. Remove (1) one # 8 X 1 3/4" screw from recess in front of console near rear view mirror. Pull front of O.E.M. console down to access wiring.
4 3. Discard trim ring. See Figure 3. Using a razor knife, carefully trim the (10) ten plastic pins flush with the shoulder. See Figure 4. FIGURE 3 FIGURE 4.
5 4. Remove OEM dome light and rear air conditioning control head. Disconnect wiring and set control head aside in a safe place. Remove the OEM ground screw near the center dome light assembly if applicable. See Figure 5. 5. Cut the headliner material between dome light opening and the front openings for OEM pod retainer arms.
6 6. Install the rear mounting bracket (item 5 pg 2 ) in the O.E.M. dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area.
7 8. If vehicle is equipped with an electronic compass, unsnap the wire harness clip and relocate toward center of vehicle. See Fig ure 9. 9. Remove and retain the two ( 2 ) door scuff plates on driver’s side.
8 10. Remove and retain the handle which mounts to top of the “B” pillar. 11. Unsnap the cover from upper and lower mo unting bracket for seat belt. Remove and retain TORX head bolt and bracket. Carefully pull panel away from side of vehicle. Unsnap upper door trim from headliner and lay aside.
9 14. Route all accessory wiring, video and audio cables, and any other added component requirements to their respective places in the vehicle. Refer to component installation instructions for wiring diagrams.
10 II. PREPARATION OF CONSOLE FOR INSTALLATION 1. Position the O.E.M. console in the front recess area of the new console (item 4 pg 2 ). Carefully fit the two together, aligning the rear compartment hinge arms through the slots in the recess pocket area.
11 IV. INSTALLATION OF OVERHEAD CONSOLE. Caution: Do not overtighten screws. Use extra support for the console until secured to the vehicle. Failure to do so may cause damage to console or installed components. 1. Cons truct a jumper harness that will connect the vehicle’s dome light wires to the lights in the console and video system.
12 7. Release video screen from locked position. Lower video screen to viewing position for a ccess to mounting locations in top of video system housing. 8. Raise video system into approximate position and connect all wiring to components. Route video cable through hole in mounting bracket.
デバイスAudiovox 1181293の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Audiovox 1181293をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox 1181293の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox 1181293の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox 1181293で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox 1181293を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox 1181293の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox 1181293に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox 1181293デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。