AudiovoxメーカーACC-52の使用説明書/サービス説明書
ページ先へ移動 of 20
MODEL ACC-52 REMOTE-CONTROL 10-DISC CD CHANGER O WNER'S MANU AL AND INST ALLA TION GUIDE OPEN.
INTRODUCTION Congratulations on your purchase of this remote mount 10 Disc CD Changer. It allows you to easily upgrade your existing car stereo system to the quality of Compact Disc entertainment. The entire system plays through your FM Stereo car radio and stereo speaker system - there’s nothing else to add or replace.
CD Magazine (P/N ACC-52MAZ) 1 pc. Index label sheet 1 pc. Owner's Manual and Installation Guide 1 pc. Self-tapping screw (M5 x 12) 4 pcs. Seals (A) 1 pc. 5 Meter Din Cable 1 pc. Hexagonal bolt with washer (M5 x 10) 7 pcs. INST ALLA TION P ARTS OTHER ACCESSORIES MAIN UNIT P ACKING LIST Changer Bracket (L) 1 pc.
Note If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation not to cause a short circuit.
5 MOUNT ON FLOOR OF TRUNK (HORIZONTAL OR 45 DEGREES) MOUNT ON SIDEWALL OF CARGO AREA MOUNT ON BULKHEAD BEHIND SEAT OF PICKUP TRUCKS MOUNT ON BACKWALL OF HATCH AREA MOUNT ON SIDE OF TRUNK SIDEWALL TRUNK MOUNTING (SEDANS) This is usually the easiest location to use as there is ample space available.
PROCEDURE FOR HORIZONT AL INST ALLA TION INST ALLA TION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen.
Hexagonal bolt with washer base (M5 x 10) Bracket (R) Bracket (L) 4 2 Attach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10). Mount the unit in place, using four self-tapping screws (M5 x 12).
4 2 Attach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10). Mount the unit in place, using four self-tapping screws (M5 x 12). Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion.
9 NOTE: When routing wires and cables from the rear of the car to the dash- board, it is best to conceal the wires under carpeting. If you do not know how to do this, your local auto me- chanic or car stereo installer should be consulted.
10 WIRING THE FM MODULE The FM module should be positioned near your existing car stereo and the 15 foot data cable should be connected to it. Make the following connections to the FM module: 15 FOOT .
CAR ANTENNA INPUT Locate your existing car radio antenna cable. This is normally a black cable about as thick as a pencil and will be plugged into a socket on the rear of your car radio. Unplug this antenna lead and plug it into the mating female socket on the FM module.
12 MOUNTING THE REMOTE CONTROL On the back of the remote control you will find an adhesive backed “Velcro” pad. Select the desired mounting area on your car dashboard that will allow ease of use and full visibility of the LCD display. Peel off the protective paper on the adhesive pad.
CONTROLS LCD Display Play/Pause ( / II) Power Off Switch (OFF) Disc Select ( + - ) Track Select ( ) Track Search ( ) Track/Disc Shuffle (SHFL) Track/Disc Repeat (RPT) Track/Disc Scan (SCN) Reset Button PREP ARING FOR OPERA TION 1. Load CD magazine bm and insert into changer as described on page 16.
USE OF CONTROLS pressing the Shuffle again, or by activating the Scan 9 or Repeat 8 functions. When the Shuffle button is pressed and held longer than 2 seconds, the SHFL and DISC indications will appear on the LCD panel and the discs in the magazine will be played in a random shuffled order, as well as the tracks on each disc.
This CD Changer is designed to be operated only on 12 volt DC negative ground systems. The unit can not be used on 24 volt or positive ground systems. TEMPERATURE The unit may not operate correctly in extremely hot or cold temperatures.
LOADING DISCS INTO THE MAGAZINE This CD Changer uses a specially-designed magazine to hold up to 10 compact discs. To load discs into the magazine, grip the tab on the magazine tray into which you will be loading a disc and pull it out gently as shown in Figure 1.
CD CHANGER OPERA TING INSTR UCTIONS This CD Changer is designed to operate through a compatible Audiovox car stereo which incorporates the controls and display functions or through the FM section of any car stereo. P l e a s e c h ec k w i th y o u r Audiovox stereo specialist for recommendations of the models that will work with this changer.
TROUBLESHOOTING An error made in operation or during installation of this product may be mistaken for a system malfunction. Please perform the checks described below before contacting your dealer or service facility. No power Magazine cannot be installed CD is not played Noise, skipping, or intermittent sound during playback.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in mater.
© 2001 Audiovox Electronics Corp., Hauppauge, NY 11788 Printed in China 128-6002.
デバイスAudiovox ACC-52の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Audiovox ACC-52をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox ACC-52の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox ACC-52の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox ACC-52で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox ACC-52を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox ACC-52の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox ACC-52に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox ACC-52デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。