AudiovoxメーカーAMP-591Aの使用説明書/サービス説明書
ページ先へ移動 of 15
Owner's Owner's Owner's Owner's Owner's Manual Manual Manual Manual Manual Model AMP-591A 300 W att S tereo Amplifier.
INDEX Specifications .............................................................................1 Precautions ................................................................................2 Installation Instructions ...............................
HIGH PERFORMANCE STEREO AMPLIFIER This power amplifier has been designed to provide high quality performance with a minimum of maintenance. However, it's performance will only be as good as the care and quality of components with which it is installed.
PRECAUTIONS 1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive ( + ) terminal of the battery.
INSTALLATION INSTRUCTIONS INSTALLATION DIAGRAM 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode.
WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for both types. Please refer to the appropriate diagrams for the system configuration you are using.
4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge.
R L LOW INPUT HPF LPF STEREO AND MIXED-MONO INPUT WIRING DIAGRAM -6- 5-PIN CONNECTOR IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT BOTH. HIGH-LEVEL (SPEAKER) OUTPUTS CAR STEREO USE THIS INP.
- LEFT SPEAKER - + RIGHT SPEAKER + STEREO MOD E:2-8 OHMS MIXED-MONO MOD E:4-8 OHMS STEREO MOD E:2-8O H M S MIXED-MONO MOD E:4-8 OHMS STEREO AND MIXED-MONO OUTPUT WIRING DIAGRAM -7- AUT.
R L LOW INPUT HPF LPF PROT PWR BASS BOOST X-OVER GAIN -8- MONO (BRIDGED) INPUT WIRING DIAGRAM CAR STEREO LOW-LEVEL RCA OUTPUTS "Y" RCA TYPE SHIELDED CABLE (NOT SUPPLIED) TO 2nd AMPLIFIER IMPORTANT USE EITHER HIGH OR LOW-LEVEL INPUTS, NOT BOTH.
-9- MONO (BRIDGED) OUTPUT WIRING DIAGRAM USE THIS OUTPUTWIRING WITH INPUT WIRING ON PAGE8 AUTO-ANTENNA LEAD USE #16 GAUGE WIRE (SEE TEXT) CAR STEREO CONNECT THIS WIRE LAST EXISTING SCREW OR BOLT CLEAN.
R L LOW INPUT HPF LPF PROT PWR BASS BOOST X-OVER GAIN HI-INPUT BRIDGED LEFT LEFT RIGHT RIGHT 20A GND REM BATT POWER FUSE SPEAKER OUT -10- OPERATION After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used.
-11- overload condition, the source of the overload must be found an d corrected to resume operation of the amplifier. Most overload conditions are caused by mis-wiring or operation into incorrect speaker loads. Re-check all wiring and connections if this situation occurs and correct as necessary.
Crossover Selector 4 is in the "HPF" setting. Adjust it to the appropriate position for t he characteristics and crossover frequency requirements of the speaker system with which t he amplifier is being used. 7 Bass Boost Switch This switch is used to accentuate the bass frequencies by adding 10 dB of boost to the signal (at 50 Hz.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in mater.
デバイスAudiovox AMP-591Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Audiovox AMP-591Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox AMP-591Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox AMP-591Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox AMP-591Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox AMP-591Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox AMP-591Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox AMP-591Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox AMP-591Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
