Remote TechnologiesメーカーT3の使用説明書/サービス説明書
ページ先へ移動 of 34
IR-PRO Professional Infrared Code Capture System T3 U n iversal System C ontr oller T3 Operation Guide v1.0.
i FEDERAL COMMUNICATIONS COMMISSION NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
T3 Universal System Controller ii BATTERY DISPOSAL For environmental reasons, your T3 universal system controller uses “environmentally sound” Lithium-ion rechargeable batteries. These batteries do not contain any poisonous heavy metals that can damage the environment.
iii Servicing. Do not attempt any service beyond that described in the operating guide. Refer all other service needs to qualified service personnel. Damage Requiring Service. The unit should be serviced by qualified service personnel when: • The power supply cord or the plug has been damaged.
T3 Universal System Controller iv Remote Technologies Incorporated is not liable for any damages caused by its products or for its failure of its products to perform, including any lost profits, lost savings, incidental damages, or consequential damages.
v Content s Federal Communications Commission Notice ---------------------- i Battery Disposal ----------------------------------------------------------- ii Safety Suggestions -----------------------.
T3 Universal System Controller vi Battery ------------------------------------------------------------------- 17 Sound -------------------------------------------------------------------- 18 Calibrate Touchscreen ------------------------------------------------ 19 Programming The T3 ---------------------------------------------------- 20 Chapter 4.
1 Chapter 1. Welcome Thank you for purchasing the T3 universal system controller. The T3 combines the power and flexibility of a graphic LCD touchscreen with an ergonomic design that permits effortless one- handed operation. This design overcomes the need for a compromise between form and function.
T3 Universal System Controller 2 UNPACKING AND INSPECTION After unpacking your new T3 universal system controller, save all of the packing materials in case you ever have to ship the unit. Thoroughly inspect the T3 and packing materials for signs of damage.
3 Chapter 2. Introduction FEATURES The T3 provides superior quality and reliability as well as these specific features: A replacement for all of the remote controls in a home theater. The T3 can reproduce all of the commands of almost any other infrared remote control.
T3 Universal System Controller 4 Both infrared (IR) and radio frequency (RF) output options. You can even use both options on the same unit. A built in motion sensor can automatically turn the unit on when it is picked up. A USB port for communication with the TheaterTouch Designer programming software.
Introduction 5 Do not disassemble the unit. Service of the T3 should be performed by authorized personnel only. CLEANING Occasional cleaning may be required, depending on use. It is recommended that you create a “Clean” button somewhere on the Home page of the T3 .
T3 Universal System Controller 6 often. Since the T3 can safely be charged after each use, a docking station is included for convenience. If left out of the docking station, the T3 will remain in sleep mode for 1 – 2 months before shutting down. At that point the battery must be recharged.
Introduction 7 GETTING STARTED Start by inserting the battery connector into the mating plug on the T3 . Make sure the connector is oriented properly before attempting to insert it. Next, turn the unit on by sliding the power switch into the “ON” position (toward the battery).
T3 Universal System Controller 8 REMOTE REFERENCE Front Touchscreen Display Home Page Button Keypad Buttons Light Sensor Page Scroll Buttons.
Introduction 9 Back Docking Station Contacts Lithium-ion Battery Pack Power Switch USB Programming Port Audio Speaker IR Transmission Window.
T3 Universal System Controller 10 DOCKING STATION REFERENCE Back Front Charge Contacts Charge LED Power Jack Wire Guide Wall Mount Holes 1-3/8 in. ( 35mm ).
11 Chapter 3. Operation THE TOUCHSCREEN DISPLAY The T3 touchscreen display is organized into a series of pages. Normally each page contains objects (buttons, text, graphics, etc.) that are related in some way. For instance, they may all display information necessary for controlling a particular DVD player.
T3 Universal System Controller 12 THE CONTROL PANEL PA GE The Control Panel page can be displayed by first setting the T3 power switch to the off position, and then pressing and holding the Home button while sliding the power switch to the on position.
Operation 13 BACKLIGHT LEVEL This button displays a window that allows you to adjust the backlight brightness and enable/disable the Ambient Light Sensor. If the light sensor is disabled, there is only one backlight level to adjust. Press the left arrow or right arrow buttons to adjust.
T3 Universal System Controller 14 If the light sensor is enabled, there are two backlight levels to adjust. Press the left arrow or right arrow buttons to adjust.
Operation 15 TIME OUT This button displays a window that allows you to adjust the amount of time the unit stays awake after the last button press. The time is variable from 1 second to 120 seconds (the default is 10 seconds). Press the arrows to the left or right of the Time Out setting to adjust the time.
T3 Universal System Controller 16 TILT SWITCH This button displays a window that allows you to adjust the settings for the built-in tilt sensor. The tilt switch is a motion detector that turns the remote on when activated. On means the tilt switch is active and will wake-up the T3 when it is moved.
Operation 17 BATTERY This button displays a window that allows you to adjust the relative amount of time that the low battery icon appears on the display. This setting will determine how much time you have between the appearance of the low battery warning and the battery becoming completely depleted.
T3 Universal System Controller 18 SOUND This button displays a window that allows you to adjust the volume of the audible speaker. The speaker sound provides feedback that a button was pressed. Press the arrows to the left or right to adjust the volume.
Operation 19 CALIBRATE TOUCHSCREEN This button runs a routine that allows you to calibrate the touchscreen. Since it normally should not be necessary to calibrate the touchscreen, this routine is included as a precaution only. Warning : Do not attempt to calibrate the touchscreen with your fingertip.
T3 Universal System Controller 20 PROGRAMMING THE T3 The T3 is programmed using RTI’s TheaterTouch Designer software. RTI dealers can download the software free of charge from: www.rticorp.com/dealers A PC running Windows ® 98SE or higher w ith a USB port is required.
21 Chapter 4. Troubleshooting If you are having problems with your T3 , please read these troubleshooting tips before contacting technical support. If you continue to have problems, see Chapter 5 for more information on contacting RTI technical support.
T3 Universal System Controller 22 IR CODE PROBLEMS If you are using an IR repeater system, make sure it is working correctly with the original OEM remote.
23 Chapter 5. Service and Support UPDATES AND NEW PRODUCTS For news about the latest updates, new product information and accessories, please visit our web site at: www.rticorp.com CONTACTING REMOTE TECHNOLOGIES INCORPORA TED For general info, you can contact RTI at: Remote Technologies Incorporated Tel.
T3 Universal System Controller 24 If you are having a problem with hardware, please note the equipment in your system, a description of the problem, and any troubleshooting you have already tried.
25 Specifications Power 3.6 VDC, 1300 mAH Li-Ion Battery Pack Power Management Automatic On/Off (tilt switch) Infrared Control Range 30 Feet (9.1m) @ 60 Degrees Infrared Frequency Range 15kHz – 460kHz Radio Frequency Control Range Up to 100 Feet (30.
T3 Universal System Controller 26 Battery Charge Time 3-4 Hours Total System Memory 32MBytes Flash (non- volatile) Device Capability Total number of devices limited only by memory Macro Capability Up .
IR-PRO Professional Infrared Code Capture System Remote Technologies Incorporated 7651 Anagram Drive Eden Prairie, MN 55344 Tel: 952-253-3100 Fax: 952-253-3131 www.
デバイスRemote Technologies T3の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Remote Technologies T3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRemote Technologies T3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Remote Technologies T3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Remote Technologies T3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Remote Technologies T3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRemote Technologies T3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Remote Technologies T3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRemote Technologies T3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
